TX-21/14GV1 Service Manual Service Support
Specifications
Parts List
Safety
Block Diagrams
Service Information
Schematic Diagrams
Exploded View
PCB Views
Service and repair of this product is supported by Panasonic's LUCI interface. This interface provides a link between the TV and a standard PC to allow a number of diagnostic and control functions to be performed. For more details contact your local Panasonic company.
BACK
EXIT
ORDER No. SM-99066
Colour Television Video Combination TX-21GV1 TX-14GV1 Z-421V Chassis SPECIFICATIONS FOR TV (All figures in brackets { } refer to TX-14GV1) Power Source: 220-240V a.c., 50Hz Power Consumption: 69W{54W} Stand-by Power Consumption: 3W Aerial Impedance: 75Ω unbalanced, Coaxial Type Receiving System: PAL I, PAL-525/60 M.NTSC NTSC (AV only) Receiving Channels: UHF E21-E69 Intermediate Frequency: Video 38,9MHz Audio 32,9MHz Colour 34,47MHz Video/Audio Terminals: AV IN (Rear) Video (21 pin) 1V p-p 75Ω Audio (21 pin) 500mV rms 10kΩ RGB (21 pin) AV OUT (Rear) Video (21 pin) 1V p-p 75Ω Audio (21 pin) 500mV rms 1kΩ AV Front Audio (RCAx1) 500mV rms 10kΩ Video (RCAx1) 1V p-p 75Ω
High Voltage: Picture Tube: Audio Output Mono (Music Power) Headphones: Accessories supplied :
28kV ± 1,5kV {25kV ± 1,5kV} A51EAL155X17 (51cm) {A34EAC01X (34cm)} 2 x 1,5W 8Ω Impedance {2W 16Ω Impedance} 300Ω Impedance 3,5mm Remote Control 2 x R6 (UM3) Batteries Indoor Antenna {14" only}
Dimensions: Height: 532mm {396,5mm} Width: 514mm {386mm} Depth: 485,2mm {367,5mm} Net weight: 24kg {13kg} Specifications are subject to change without notice. Weights and dimensions shown are approximate. NOTE: This Service Manual should be used in conjunction with the Z-421V Technical guide.
SPECIFICATIONS FOR VCR GENERAL
temperature format
AUDIO
VIDEO
5°C ~ 35°C (operating) -20°C ~ 60°C (storage temperature) standard
tape width
12.65mm
tape speed max. recording time with full-size cassette recording system
SP: 23.39mm/sec LP: 11.70mm/sec SP: 240min. with E-240 video cassette LP: 480min. with E-240 video cassette longitudinal track
input
-3.8dBm(500mVrms), more than 47kΩ, unbalanced.
output frequency range
-3.8dBm(500mVrms),less than 1kΩ, unbalanced 100Hz to 8KHz
signal to noise ratio
40dB(more than)
signal system
PAL/SECAM colour and CCIR mono chrome signals, 625lines/50fields. Rotary 4-head helical scan with a slant double azimuth combination video head. 1Vp-p, 75Ω, unbalanced
recording system input output signal to noise ratio
1Vp-p, 75Ω, unbalanced 45dB with NETTETE IMAGE control at center position.
horizontal resolution
240 lines with NETTETE IMAGE control at center position
Panasonic CS ( U.K. ) Ltd. WILLOUGHBY ROAD, BRACKNELL, BERKS., RG12 8FT.
CONTENTS SAFETY PRECAUTIONS..........................................................................................................................................................2 SERVICE HINTS & DISASSEMBLY .........................................................................................................................................3 ADJUSTMENT PROCEDURE...................................................................................................................................................6 ALIGNMENT SETTINGS...........................................................................................................................................................7 DESCRIPTION OF THE VCR MECHANISM ............................................................................................................................8 BLOCK DIAGRAMS ................................................................................................................................................................34 PARTS LOCATION (TV) .........................................................................................................................................................37 REPLACEMENT PARTS LIST (TV) ........................................................................................................................................38 PARTS LOCATION (VCR) ......................................................................................................................................................47 REPLACEMENT PARTS LIST (VCR) .....................................................................................................................................48
SAFETY PRECAUTIONS GENERAL GUIDE LINES 1. 2.
3.
4. 5.
6.
It is advisable to insert an isolation transformer in the a.c. supply before servicing a hot chassis. When servicing, observe the original lead dress in the high voltage circuits. If a short circuit is found, replace all parts that have been overheated or damaged by the short circuit. After servicing, see that all the protective devices such as insulation barriers, insulation papers, shields and isolation R-C combinations are correctly installed. When the receiver is not being used for a long period of time, unplug the power cord from the a.c. outlet. Potentials as high as 29,5kV { 26,5kV } are present when this receiver is in operation. Operation of the receiver without the rear cover involves the danger of a shock hazard from the receiver power supply. Servicing should not be attempted by anyone who is not familiar with the precautions necessary when working on high voltage equipment. Always discharge the anode of the tube. After servicing make the following leakage current checks to prevent the customer from being exposed to shock hazard.
5. 6.
Reverse the a.c. plug at the outlet and repeat each of the above measurements. The potential at any point should not exceed 1,4Vrms. In case a measurement is outside the limits specified, there is a possibility of a shock hazard, and the receiver should be repaired and rechecked before it is returned to the customer.
HOT CHECK CIRCUIT a.c. VOLTMETER
2kΩ 10 Watts
WATER PIPE (EARTH)
TO INSTRUMENT’S EXPOSED METALLIC PARTS
Fig. 1.
LEAKAGE CURRENT COLD CHECK 1. 2. 3.
Unplug the a.c. cord and connect a jumper between the two prongs of the plug. Turn on the receiver’s power switch. Measure the resistance value with an ohmmeter, between the jumpered a.c. plug and each exposed metallic cabinet part on the receiver, such as screw heads, aerials, connectors, control shafts etc. When the exposed metallic part has a return path to the chassis, the reading should be between 4M ohm and 20M ohm. When the exposed metal does not have a return path to the chassis, the reading must be infinite.
X-RADIATION WARNING 1. 2.
NOTE: It is important to use an accurate periodically calibrated high voltage meter. 1. Set the brightness to minimum. 2. Measure the high voltage. The meter should indicate. 28kV ± 1,5kV { 25kV ± 1,5kV }. If the meter indication is out of tolerance, immediate service and correction is required to prevent the possibility of premature component failure. 3. To prevent any X-Radiation possibility, it is essential to use the specified tube.
LEAKAGE CURRENT HOT CHECK 1. 2.
3. 4.
The potential sources of X-Radiation in TV sets are the high voltage section and the picture tube. When using a picture tube test jig for service, ensure that the jig is capable of handling 29,5kV { 26,5kV } without causing X-Radiation.
Plug the a.c. cord directly into the a.c. outlet. Do not use an isolation transformer for this check. Connect a 2kΩ 10W resistor in series with an exposed metallic part on the receiver and an earth, such as a water pipe. Use an a.c. voltmeter with high impedance to measure the potential across the resistor. Check each exposed metallic part and check the voltage at each point.
2
SERVICE HINTS How to remove the rear cover 1) Remove the screws as shown in Fig.2/Fig.3. TX-21GV1 TX-14GV1
Screw
Screw
Screw
Screw
Fig.3. Fig.2.
DISASSEMBLY 1) Remove the 2 cable ties shown in Fig.4. 2) Remove the 7 connectors shown in Fig.5.
Fig.2.
CRT Board Focus Cable Ties Screen Power Board
Main Board Fig.4.
Connectors Fig.5.
3
DISASSEMBLY (Cont.) 3) 4) 5) 6)
Remove the 6 screws, three each side, from the top cover, as shown in Fig.6. Remove the speaker connector as shown in Fig.6. Remove earth strap shown in Fig.7. Lift top cover and remove main pcb.
Speaker Connector
Earth strap
Screws Fig.6.
Top Cover Fig.7.
7) Remove the 5 screws as shown in Fig.8. 8) Remove the head connector seal cover shown in Fig.8. 9) Remove the 4 connectors shown in Fig.9. Head Connector Seal Cover
Screws Fig.8.
Connectors
Fig.9. Connectors
4
DISASSEMBLY (Cont.) 10) 11)
Remove the 5 screws shown in Fig.10. Release the 5 chassis frame clips (shown in Fig.11.) and remove the main P.C.B. from the chassis frame.
Screws
Screws
Fig.10.
Clips
Clips
Fig.11.
5
ADJUSTMENT PROCEDURE Item / Preparation
Adjustments
Sub Tuner AFT 1) Set a signal generator with -RF FREQUENCY = 38,9MHz -RF OUTPUT LEVEL = 80±5dBuV. 2) Connect a signal generator RF output to TP2 (TUNER IF OUTPUT). Ensure there is no signal input to the TUNER. 3) Connect the DC voltage meter to TP3.
Adjust L201 (AFT COIL) for 2,2V ± 0,1V.
Main Tuner AGC 1) Set a pattern generator with RF level 60 ± 2dBuV, 210,25MHz. 2) Connect an oscilloscope to P101 (Tuner AGC Input).
Adjust using "AGC UP/DOWN" key until the voltage drops to 1,0Vdc ± 0.2Vdc below its maximum voltage.
Sub Tuner AGC 1) Set a pattern generator with RF level 60 ± 2dBuV, 210,25MHz. 2) Connect an oscilloscope to P101 (Tuner AGC Input).
Press the "SUB AGC" key in Service mode and monitor the SUB TUNER picture whilst adjusting R202 (SUB AGC VR) to 1,0Vdc ±0.2Vdc below its maximum voltage.
Screen 1) Apply a Colour Bar Pattern signal. 2) Connect an oscilloscope to P906 (CRT Cathode RGB). 3) Press the SCREEN key.
Adjust the screen volume on the FBT so that the highest black level voltage is 130V ± 5Vdc {150V ± 5Vdc}.
Focus 1) Apply a RETMA Pattern signal.
Adjust FOCUS VOLUME on the FBT for optimum setting.
White Balance 1) Apply a Colour Bar Pattern signal.
Adjust the RGB UP/DOWN key to obtain optimum WHITE BALANCE.
X-Position Adjustment, P2 and P3
Adjust, with the corn screw, until both TRK MAX and TRK MIN have the same size of envelope. Adjust P2, P3 so that both the beginning and the end of the envelope waveform are flat.
1) Play DP-2 Test tape (Colour bar, Audio 6KHz). 2) Enter Service Mode using Service Remote and deactivate Auto-Tracking by pressing ATK-OFF key. 3) Set oscilloscope to CHOP mode and connect CH1 to VIDEO HEAD SW (PYO4 pin 6). Connect CH2 to the PB ENVE (PYO4 pin 4) and trigger CH1. Azimuth Adjustment 1) Connect an oscilloscope to the AUDIO OUTPUT terminal (P601).
After test tape playback, adjust the output level, using the outer screw of the A/C head to obtain maximum waveform. (6KHz -3,8dBm +1dBm / -3dBm.) Fix the azimuth screw with locking paint.
6
ALIGNMENT SETTINGS: (The figures below are nominal and used for representative purposes only.) 1) Place the TV in Programme position 70, set the Sharpness to minimum position, press the down button (- / v) on the customer controls at the front of the TV and at the same time press the VCR INDEX button on the remote control, this will place the TV into the Service Mode. 2) Press the RED / GREEN buttons to step up / down through the functions. 3) Press the YELLOW / BLUE buttons to alter the function values. 4) To exit the Service Mode, press the "EXIT" button. Alignment Function Blue correction
Green correction
Settings / Special features B
Optimum setting (for white balance).
23 G
Optimum setting (for white balance).
23 Red correction
R
Optimum setting (for white balance).
24 Set Pattern generator with RF level 60+/- 2dBuV, 210.25MHz. Connect oscilloscope to P101 (Tuner AGC input). Adjust AGC using Yellow /Blue buttons until the voltage drops to 1,0Vdc ±0.2Vdc below its maximum voltage.
AGC AGC
41
Press this button to access SUB TUNER AGC adjustment. Press once: picture is displayed in colour. Press twice: picture is displayed in black and white.
SUB AGC 1 Sub AGC
Horizontal Centre
Vertical Size
H-CENTER
Optimum setting.
32 V-SIZE
Optimum setting.
51 Vertical Centre
V-CENTER
Optimum setting.
30 Vertical Slope
V.SLOPE
Optimum setting.
32 S-Correction
S-CORR
Optimum setting.
20 OSD language
OSD Language
OSD Position Set
English Français Italiano Español Nederlands Deutsch
Adjust to change order of language selection
OSD POSITION SET
7
Optimum setting.
DESCRIPTION OF THE VCR MECHANISM Characteristic of the K-Deck mechanism _
K-Mecha Deck follows the VHS standard and uses three motors (DRUM MOTOR, CAPSTAN MOTOR and L/C MOTOR). The L/C MOTOR is used to drive FRONT LOADING.
_
The deck recognises each mode by using a 4-BIT MODE signal. This 4-BIT MODE signal is generated by the CAM SWITCH, which is driven by the L/C MOTOR.
_
There are 7 MODES which are utilised (EJECT / INITIAL / REV / IDLE / PLAY, STOP, SLOW / BRAKE / FF & REW).
_
The reduction of the mode shifting time, i.e. picture playing time, is enabled by using the FULL LOADING SYSTEM that has the DRUM wrapped by the tape.
_
The Main PCB is separated from the Deck. When assembling, it is connected by the B-B TYPE CONNECTOR.
_
The CAPSTAN MOTOR and DRUM MOTOR are directly connected to the MAIN PCB DECK
ASSEMBLY DIAGRAM OF DECK ASSEMBLY TOP VIEW
18
17
19
16
1
15
2
14 3 13
4
12
5
6
20
8
7
9
10 11
Fig.12. 1) 2) 3) 4) 5) 6) 7) 8)
EARTH BRACKET ASSEMBLY FE HEAD S SLANT POLE ASSEMBLY TENSION BAND ASSEMBLY REEL TABLE MAIN BASE ASSEMBLY S SUB BRAKE ASSEMBLY S MAIN BRAKE ASSEMBLY
9) 10) 11) 12) 13) 14) 15) 16)
IDLER PLATE TOTAL ASSEMBLY T MAIN BRAKE ASSEMBLY T-BRAKE ASSEMBLY RELAY LEVER CAPSTAN MOTOR PINCH LEVER TOTAL ASSEMBLY L/C BRACKET TOTAL ASSEMBLY CAM GEAR
8
17) 18) 19) 20)
A/C HEAD TOTAL ASSEMBLY T SLANT POLE ASSEMBLY DRUM TOTAL ASSEMBLY RECORD SAFETY LEVER
ASSEMBLY DIAGRAM AND MAJOR PARTS CHECK BOTTOM VIEW 10
2 9
1
7
8 4
3
6 5 Fig.13.
1) 2) 3) 4)
CAPSTAN MOTOR F/L RACK CONNECT PLATE REEL BELT
5) 6) 7) 8)
REEL GEAR TOTAL ASSEMBLY 9) DRUM TOTAL ASSEMBLY RECORD SAFETY LEVER 10) LOADING RACK ASSEMBLY L LOADING ASSEMBLY R LOADING ASSEMBLY
9
DISASSEMBLY AND REPLACEMENT FRONT LOADING ASSEMBLY REMOVAL NOTE: The FRONT LOADING ASSEMBLY can be removed only in the eject position. 1) Remove the two screws (A0400)as displayed in fig.14 below.
A0400
Front loading assembly separation Fig.14.
10
DISASSEMBLY OF THE VCR 1) Remove the screw holding the F/L BRACKET R and move the F/L BRACKET R in the direction of the arrow to separate it from the TOP PLATE and CASSETTE HOLDER ASSEMBLY. 2) Remove the CASSETTE HOLDER ASSEMBLY.
Disassembly of the front loading assembly Fig.15.
3) Remove the screw holding the PRISM LINK R and remove the PRISM LINK R from the F/L BRACKET R.
Disassembly of the front loading bracket (right) Fig.16.
11
DISASSEMBLY OF THE VCR (Cont.) 4) Remove the screw holding the PRISM LINK L. 5) Release the hook B by pushing it in the direction of the arrow and remove the DOOR OPENER.
Disassembly of the top plate Fig.17. 6) Remove the LOADING LEVER ASSEMBLY by pressing the connected section of the LOADING LEVER ASSEMBLY in the direction of the arrows. 7) Remove the SAFETY SPRING between the SAFETY LEVER and the CASSETTE HOLDER PLATE. 8) Remove the RELEASE SPRING between the RELEASE LEVER and the SAFETY LEVER R.
Disassembly of the cassette holder assembly Fig.18.
12
DISASSEMBLY OF THE VCR (Cont.) NOTE Reassemble the FRONT LOADING MECHANISM in the reverse order. Confirm that the two bosses on the left side of the CASSETTE HOLDER are inserted into the groove on the left s ide of the top plate. Insert the two bosses on the right side of the cassette holder into the groove of the FRONT LOADING BRACKET R.(Fig.19).
INSERT POINTS TOP PLATE
Assembly of the front loading assembly Fig.19.
DRUM ASSEMBLY / EARTH BRACKET ASSEMBLY REMOVAL 1) Remove three screws (1) fixing the DRUM TOTAL ASSEMBLY. 2) Remove the EARTH BRACKET ASSEMBLY (2). 3) Carefully lift the DRUM TOTAL ASSEMBLY (3) from the DECK MECHANISM, taking care not to damage or touch the VIDEO HEAD.
NOTE 1) After assembling the DRUM TOTAL ASSEMBLY, confirm that the tape runs smoothly. (Refer to ADJUSTMENT OF THE TAPE TRANSPORTING SYSTEM). 2) When assembling the EARTH BRACKET ASSEMBLY, a 3x12 screw should be used and all other parts should use 3x10 screws, as indicated.
Drum total assembly & earth bracket assembly removal Fig.20.
13
REEL BELT, LOADING RACK ASSEMBLY, S/T SLANT POLE ASSEMBLY REMOVAL 1) Turnover the DECK MECHANISM and remove the REEL BELT (1). 2) Remove one POLY WASHER (2). 3) Remove the LOADING RACK ASSEMBLY (3). 4) Remove R and L LOADING ASSEMBLIES (4&5). 5) Remove the S and T SLANT POLES (6&7) by pulling them in the direction of the arrows.(Fig.21)
CAUTION Take care not to get the GUIDE ROLLERS of the S/T SLANT POLES stained with grease. When reassembling, please refer to Fig.22.
Reel belt, loading rack assembly, right & left loading assemblies & supply and takeup slant pole assembly removal Fig.21.
LOADING GEAR (R) LOADING GEAR (L)
TRIANGLE MARK ON LOADING GEAR (L)
LOADING RACK HOLE OF LOADING RACK
CIRCULAR MARK ON LOADING GEAR (R) NOTCH IN LOADING GEAR (R)
Assembly of the Right & Left Loading Assembly & Loading Rack Assembly Fig.22.
14
A/C HEAD ASSEMBLY REMOVAL 1) Remove the hex nut (1) from the A/C HEAD POST (4) of the MAINBASE.(Fig.23) 2) Remove the A/C HEAD ASSEMBLY (2) from the MAINBASE. 3) Remove the A/C HEAD SPRING (3) from the A/C HEAD ASSEMBLY.
NOTE After reassembling, adjust the TAPE TRANSPORTING SYSTEM, referring to ADJUSTMENT OF THE TAPE TRANSPORTING SYSTEM. After adjusting the TAPE TRANSPORTING SYSTEM spread the A/C HEAD, A/C NUT, AZIMUTH SCREW and TILT SCREW with LOCKING PAINT.
L/C BRACKET ASSEMBLY REMOVAL 1) Remove the screw (1) from the L/C BRACKET ASSEMBLY (2).(Fig.24) 2) Remove the L/C BRACKET ASSEMBLY from the MAINBASE (3).
PINCH LEVER TOTAL ASSEMBLY REMOVAL 1) Remove the POLY WASHER (3) from the PINCH LEVER POST of the MAINBASE. 2) Unhook the PINCH LEVER SPRING (4) from the hook of the MAINBASE (5) and remove the PINCH LEVER TOTAL ASSEMBLY (9).
CAUTION Take care not to coat Grease, Oil or other substances on the surface of the PINCH ROLLER.
Lift cam bracket, pinch lever, cam gear, relay lever, front loading rack removal Fig.24.
Disassembly of the audio control head assembly Fig.23.
CAM GEAR, RELAY LEVER AND F/L RACK REMOVAL 1) Remove the CAM GEAR from the MAINBASE (7). (Fig.24) 2) Remove the RELAY LEVER from the MAINBASE (6). 3) Remove the F/L RACK from the MAINBASE by pulling it in the direction of the arrow (8). NOTE When reassembling refer to Fig.25/Fig.26. (Page 16)
15
CAM GEAR, RELAY LEVER AND F/L RACK REMOVAL (Cont.)
CAM GEAR
DATUM HOLE OF CAM GEAR DATUM HOLE OF MAINBASE
F/L RACK
Assembly of the cam gear and front loading rack Fig.26.
Assembly of the cam gear and relay lever Fig.25.
S/T MAIN AND SUB BRAKE ASSEMBLY REMOVAL 1) Unhook the MAIN BRAKE SPRING (1) from the T MAIN BRAKE LEVER (3) and remove the T MAIN BRAKE ASSEMBLY (3). 2) Remove the S MAIN BRAKE ASSEMBLY (2) from the MAINBASE (8). 3) Unhook the S SUB BRAKE SPRING (4) from the MAINBASE and remove the S SUB BRAKE LEVER ASSEMBLY (5) from the MAIN BASE (8). 4) Unhook the T SUB BRAKE SPRING (6) from the MAINBASE and remove the T SUB BRAKE LEVER ASSEMBLY (7).
Supply and takeup main and sub brakes removal Fig.27.
16
TENSION BAND ASSEMBLY REMOVAL 1) Remove the TENSION SPRING (2) from the MAINBASE (1). 2) Turn the DECK MECHANISM over. 3) After separating the tab of hook "A", remove the TENSION BAND ASSEMBLY (3).
NOTE After assembling the TENSION BAND ASSEMBLY on the MAINBASE, adjust the position of the TENSION POLE as shown in fig.30. Avoid getting GREASE, OIL or foreign substances on the FELT of the BAND BRAKE. Take care not to deform tab "A" when separating it.
Tension band assembly removal Fig.29.
Tension band assembly removal Fig.28. DATUM HOLE OF MAINBASE DATUM HOLE OF TENSION LEVER
Adjustment of the tension pole position Fig.30.
17
CAPSTAN MOTOR REMOVAL 1) Remove the 3 screws fixing the CAPSTAN MOTOR and separate the CAPSTAN MOTOR.
Capstan motor removal Fig.31.
IDLER PLATE TOTAL ASSEMBLY & S/T REEL TABLE REMOVAL 1) Remove one POLY WASHER (1) from the REEL GEAR POST (2) and remove the IDLER PLATE TOTAL ASSEMBLY (3) from the MAIN BASE. 2) Remove the S/T REEL TABLES (4) and two POLY SLIDERS (5) from the DECK MECHANISM.
CAUTION When disassembling or assembling the IDLER PLATE TOTAL ASSEMBLY, take care not to bend it.
Idler plate total assembly and supply and takeup reel tables removal Fig.32.
18
FE HEAD REMOVAL 1) Remove the screw (1) fixing the FE HEAD (2) and remove the FE HEAD from the MAINBASE.
Fe head removal Fig.33.
REEL GEAR TOTAL ASSEMBLY & CONNECT PLATE REMOVAL 1) Turn over the DECK MECHANISM and remove the POLY WASHER (1) from the REEL GEAR POST (2). 2) After separating tab "B" of the MAINBASE, remove the REEL GEAR TOTAL ASSEMBLY (3) from the MAINBASE. 3) Remove the CONNECT PLATE (4) from the MAINBASE by pushing it in the direction of the arrow.
Reel gear total assembly and connect plate removal Fig.34.
NOTE When removing the CONNECT PLATE with the F/L RACK installed, take care not to damage or bend the CONNECT PLATE. After assembling or disassembling the REEL GEAR TOTAL ASSEMBLY, take care not to get OIL, GREASE or other substances on the REEL BELT. Take care not to deform or break tab "B". Check the assembly state & the operating state of the REEL GEAR TOTAL ASSEMBLY before assembling. After reassembling check the FF, REW, PLAY and REVIEW MODES and the existence of noise when operating the MODES.
19
MECHANICAL ADJUSTMENT When operational problems occur or the mechanism is reassembled, be sure to confirm the following instructions. 1) Make sure that the DATUM HOLE of the CAM GEAR is aligned with the DATUM HOLE in the MAINBASE in the EJECT mode, as shown in fig.35. CAM GEAR DATUM HOLE OF CAM GEAR
DATUM HOLE OF MAIN BASE
F/L RACK
Datum position of front loading rack and cam gear Fig.35. 2) Make sure that part "A" of the RELAY LEVER, when assembled in the CONNECT PLATE, is fully rotated to the left side of "B" of the MAINBASE, and is touching boss "C" of the MAINBASE, as shown in fig.36.
Datum position of relay lever and cam gear Fig.36.
20
MECHANICAL ADJUSTMENT (Cont.) 3) When reassembling the L/C BRACKET TOTAL ASSEMBLY on the MAINBASE, make sure that the two triangular marks of the CAM SWITCH are aligned with each other as shown in fig.37.
TRIANLE MARKS MUST MEET EACH OTHER
Datum position of cam switch triangular marks Fig.37. 4) Make sure that boss "A" of the PINCH LEVER TOTAL ASSEMBLY is positioned at point "B" of the CAM GEAR, as shown in fig.38.
Datum position of pinch lever total assembly and cam gear Fig.38.
21
MECHANICAL ADJUSTMENT (Cont.) 5) Ensure that the triangular mark "A" on the L LOADING ASSEMBLY is aligned with the notch "B" on the R LOADING ASSEMBLY, as shown in fig.39. 6) Ensure that the teeth of the LOADING RACK ASSEMBLY are aligned with those of the R LOADING ASSEMBLY so that the hole of the LOADING RACK ASSEMBLY aligns with the circular mark on the R LOADING ASSEMBLY, as shown in fig.39.
R LOADING ASSEMBLY (B)
L LOADING ASSEMBLY
TRIANGULAR MARK ON L LOADING ASSEMBLY (A)
LOADING RACK ASSEMBLY HOLE OF LOADING RACK
CIRCULAR MARK OF R LOADING ASSEMBLY
NOTCH IN R LOADING ASSEMBLY
Datum position of loading rack assembly and right and left loading lever assembly Fig.39.
22
BACK TENSION MEASUREMENT 1) Confirm the position of the TENSION POLE is correct. Refer to "TENSION POLE POSITION ADJUSTMENT" 2) Play back a T-120 TAPE at its centre position without assembling F/L ASSEMBLY and wait until the TAPE run is stabilised (about 5-10 secs). 3) Bring the TENTELOMETER into contact with the TAPE and measure the BACK TENSION. The result should be between 25 and 33 grams. 4) If the measuring result is not within this specification, refer to the NOTE below or repeat "TENSION POLE POSITION ADJUSTMENT".
TENTELOMETER
DATUM HOLE TAPE
Back tension measurement Fig.40.
Note If the measuring result is not within the specification, change the TENSION SPRING position. (To decrease the result, choose hook A. Otherwise choose hook B). Confirm that all three probes of the Tentelometer are in contact with the TAPE. During this process do not touch any other parts of the MECHANISM (i.e. MAINBASE). It is recommended that this measurement be repeated at least three times for an accurate reading.
23
MECHANICAL MODE (OPERATING THE VCR WITHOUT A CASSETTE TAPE) 1) 2) 3) 4)
Remove the FRONT LOADING MECHANISM from the DECK MECHANISM. Pull the F/L RACK. The S/T POLE BASES are loaded and PLAY BACK MODE starts. Turn off the power when the MECHANISM is in the desired position.
TENSION POLE POSITION ADJUSTMENT 1) Change MECHANICAL MODE to PLAY MODE. 2) Confirm that the datum hole of TENSION LEVER is aligned with the datum hole of the MAIN BASE. To adjust turn the BAND BRAKE ADJUST CAP clockwise or anti-clockwise until the two datum holes are aligned with each other.
DATUM HOLE OF MAIN BASE DATUM HOLE OF TENSION LEVER
Tension pole position adjustment Fig.41. BAND BRAKE ADJUST CAP
Tension pole position adjustment Fig.41.
24
ADJUSTMENT OF TAPE TRANSPORTING SYSTEM Generally the TAPE TRANSPORTING SYSTEM has been precisely adjusted in the factory and does not ordinarily require readjustment, but when noise and tape damage take place and part assemblies that comprise the TAPE TRANSPORTING SYSTEM are replaced, check and readjust the TAPE TRANSPORTING SYSTEM. Refer to the following flow chart in order to adjust the TAPE TRANSPORTING SYSTEM.
CLEANING
b DRUM TOTAL ASSEMBLY b A/C HEAD ASSEMBLY b PINCH LEVER TOTAL ASSEMBLY
S/T GUIDE ROLLER HEIGHT ADJUSTMENT
S/T GUIDE POST FLANGE
A/C HEAD AS ADJUSTMENT (TILT ADJUSTMENT)
AUDIO AZIMUTH ADJUSTMENT
A/C HEAD ADJUSTMENT
X-POSITION ADJUSTMENT
PLAYBACK PHASE ADJUSTMENT
LINEARITY ADJUSTMENT b S POLE BASE ASSEMBLY b T POLE BASE ASSEMBLY b TENSION LEVER ASSEMBLY
DRUM ENTRANCE/EXIT ENVELOPE FINE TUNING
REVIEW~PLAY CHANGING OPERATION CHECK
AUDIO OUTPUT CHECK (A/C HEAD TILT & HEIGHT ADJUSTMENT) AUDIO AZIMUTH ADJUSTMENT
X-POSITION ADJUSTMENT
TRACKING
25
ADJUSTMENT OF TAPE TRANSPORTING SYSTEM (Cont.)
The schematic diagram of tape transporting system Fig.42. When the parts as shown in fig.42 are replaced, the TAPE TRANSPORTING SYSTEM has changed. To prevent this, it is essential to observe the following instructions.
ADJUSTMENT OF THE S/T GUIDE ROLLER 1) Play back a T-120 TAPE. 2) Make sure that excessive TAPE wrinkle does not occur at each S/T GUIDE ROLLER. 3) If TAPE wrinkle is observed at the S/T GUIDE ROLLER, adjust to remove occurrence of wrinkles.
ADJUSTMENT OF THE A/C HEAD ASSEMBLY (TILT ADJUSTMENT) 1) Play back a T-120 TAPE and check the running condition of the TAPE at the lower flanges of the T GUIDE POST ASSEMBLY, see fig.42. 2) Adjust the A/C HEAD TILT SCREW until the TAPE runs stable as shown in fig.43.
A/C HEAD TILT SCREW CLOCKWISE
A/C HEAD TILT SCREW ANTI-CLOCKWISE
Audio control head assembly adjustment (Tilt adjustment) Fig.43.
26
ADJUSTMENT OF THE AUDIO AZIMUTH 1) Play back the ALIGNMENT CASSETTE TAPE (NTSC:DN2 (SP 7KHz), PAL: DP2 (SP 6KHz)) 2) Observe audio signals on an OSCILLOSCOPE. 3) Turn the A/C HEAD AZIMUTH SCREW to obtain the maximum audio output signal (-9 ~-3dBm) Fig.44.
Audio control head assembly Fig.44.
HEIGHT ADJUSTMENT OF A/C HEAD 1) Play back a T-120 TAPE. 2) Make sure that the gap is 0,25mm between the lower end of TAPE and that of A/C HEAD Fig.45. 3) When the gap is larger than 0,25mm, turn the A/C HEAD HEIGHT ADJUST NUT anti-clockwise. When the gap is smaller than 0,25mm turn it clockwise. Repeat this procedure until 0,25mm is obtained.
GAP Audio control head assembly adjustment (Height adjustment) Fig.45.
27
X-POSITION ADJUSTMENT S/W PULSE TEST PIN ENVELOPE TEST PIN OSCILLOSCOPE VR CONTROL ADJUST BOSS
TEST POINTS MEASURING EQUIPMENT ADJUSTMENT 1) 2) 3) 4) 5)
PATH ADJ. JIG PATH ADJ. JIG PATH ADJ. JIG MAIN BASE
Connect the path adjustment fixture to PTO1 of the MAIN CIRCUIT BOARD. Play back the ALIGNMENT TAPE (COLOUR BAR ALIGNMENT). Connect channel-1 scope probe to S/W PULSE TEST PIN of PATH ADJ. JIG. Connect channel-2 scope probe to ENVELOPE TEST PIN of PATH ADJ. JIG. Turn the VR CONTROL to the centre point. (If the VR CONTROL is completely turned anti-clockwise, it is positioned on another tracking centre.) 6) With the VR CONTROL in the centre state, turn the ADJUST BOSS by using a FLAT TYPE SCREW DRIVER and adjust the X-POSITION to obtain maximum envelope waveform.
CENTRE
CCW
CW
CENTRE
X-position adjustment Fig.46.
28
PLAYBACK PHASE ADJUSTMENT TEST POINTS MEASURING EQUIPMENT ADJUSTMENT
S/W PULSE TEST PIN VIDEO OUT OSCILLOSCOPE VR595 (PG SHIFTER)
PATH ADJ. JIG MAIN CIRCUIT BOARD MAIN CIRCUIT BOARD
The Phase generator (PG) shifter decides the VIDEO HEAD switching point when a TAPE is played back. In case the Phase generator (PG) shifter is not correctly tuned, HEAD switching noise or vertical jitter may occur. 1) Connect the PATH ADJ. JIG to PTO1 of the MAIN CIRCUIT BOARD. 2) Play the ALIGNMENT TAPE (COLOUR BAR SIGNAL OR MONOSCOPE SIGNAL). 3) Connect the channel-1 scope probe to the S/W PULSE TEST PIN of the PATH ADJ. JIG. 4) Connect the channel-2 scope probe (1V/div.) to the VIDEO OUT of the MAIN CIRCUIT BOARD. 5) Play back the ALIGNMENT TAPE. 6) Adjust the PG volume for time interval of 6,5Hz±0,5Hz between switching pulse and V-sync signal. SWITCHING
SW. PULSE
V.SYNC
VIDEO OUTPUT
Playback phase adjustment Fig.47.
29
LINEARITY ADJUSTMENT TEST POINTS MEASURING EQUIPMENT ADJUSTMENT 1) 2) 3) 4) 5) 6)
S/W PULSE TEST PIN ENVELOPE TEST PIN OSCILLOSCOPE VR CONTROL S/T GUIDE ROLLER
PATH ADJ. JIG PATH ADJ. JIG PATH ADJ. JIG TAPE TRANSPORTING SYSTEM
Connect the PATH ADJ. JIG to PTO1 of the MAIN CIRCUIT BOARD. Play back the ALIGNMENT TAPE (COLOUR BAR SIGNAL). Connect the channel-1 scope probe to the S/W PULSE TEST PIN of the PATH ADJ. JIG. Connect the channel-2 scope probe to the ENVELOPE TEST PIN of the PATH ADJ. JIG. Adjust the VR CONTROL of the PATH ADJ. JIG for maximum envelope signal output of the alignment tape. Adjust the S/T GUIDE ROLLER until the envelope signal waveforms of the entrance and exit sides are as shown fig.48. a: Max output of envelope b: Min output of envelope
Linearity adjustment Fig.48.
30
DRUM ENTRANCE / EXIT TEST POINTS MEASURING EQUIPMENT ADJUSTMENT
S/W PULSE TEST PIN ENVELOPE TEST PIN OSCILLOSCOPE VR CONTROL S/T GUIDE ROLLER
PATH ADJ. JIG PATH ADJ. JIG PATH ADJ. JIG TAPE TRANSPORTING SYSTEM
1) 2) 3) 4) 5)
Connect the PATH ADJ. JIG to PTO1 on the MAIN CIRCUIT BOARD. Play back the ALIGNMENT TAPE (COLOUR BAR SIGNAL). Connect the channel-1 scope probe to the S/W PULSE TEST PIN of the PATH ADJ. JIG. Connect the channel-2 scope probe to the ENVELOPE TEST PIN of the PATH ADJ. JIG. When turning the VR CONTROL of the PATH ADJ. JIG clockwise or anti-clockwise, confirm that the envelope thickness changes uniformly. 6) If the envelope is not uniform and regular, adjust the S/T GUIDE ROLLER.
DRUM ENTRANCE
Fine tuning of the envelope at the drum entrance/exit (II) Fig.50 DRUM EXIT
Fine tuning of the envelope at the drum entrance/exit (I) Fig.49
31
REVIEW / PLAY TEST POINTS MEASURING EQUIPMENT ADJUSTMENT
S/W PULSE TEST PIN ENVELOPE TEST PIN OSCILLOSCOPE VR CONTROL S/T GUIDE ROLLER
PATH ADJ. JIG PATH ADJ. JIG PATH ADJ. JIG TAPE TRANSPORTING SYSTEM
1) 2) 3) 4) 5)
Connect the PATH ADJ. JIG to PTO1 of the MAIN CIRCUIT BOARD. Play back the ALIGNMENT TAPE (SP COLOUR BAR SIGNAL). Connect the channel-1 scope probe to the S/W PULSE TEST PIN of the PATH ADJ. JIG. Connect the channel-2 scope probe to the ENVELOPE TEST PIN of the PATH ADJ. JIG. Adjust the VR CONTROL of the PATH ADJ. JIG to the centre to obtain the maximum envelope signal of the ALIGNMENT TAPE. 6) After operating the VCR in the REVIEW MODE about 15 secs, change operation mode from REVIEW MODE to PLAY MODE and then make sure that the envelope waveform is restored to the maximum condition within 3 seconds. 7) If the requirement is not satisfied, make sure that the TAPE runs normally at the lower part of the T GUIDE POST. Then adjust the S/T GUIDE ROLLER precisely.
ENVELOPE WAVEFORM
PICTURE
Check of transitional operation (from review waveform to play waveform) Fig.51
32
AUDIO OUTPUT (A/C HEAD TILT & HEIGHT ADJUSTMENT) TEST POINTS MEASURING EQUIPMENT
1) 2) 3) 4)
AUDIO OUTPUT OSCILLOSCOPE
AUDIO OUTPUT JACK
Connect the OSCILLOSCOPE to the AUDIO OUTPUT JACK. Play back the ALIGNMENT TAPE (NTSC DN1 (SP 1KHz), PAL DP1 (SP 1KHz)). Check the AUDIO OUTPUT SIGNAL is -9~-3dBm. If the requirement (3) is not satisfied, adjust the A/C HEAD TILT SCREW and A/C HEAD HEIGHT NUT to obtain the maximum audio output.
A/C HEAD AZIMUTH ADJUSTMENT TEST POINTS MEASURING EQUIPMENT
1) 2) 3) 4)
AUDIO OUTPUT OSCILLOSCOPE
AUDIO OUTPUT JACK
Connect the OSCILLOSCOPE to the AUDIO OUTPUT JACK. Play back the ALIGNMENT TAPE (NTSC DN2 (SP 7KHz), PAL DP2 (SP 6KHz)). Adjust the A/C HEAD AZIMUTH SCREW to obtain the audio output -9~-3dBm. Repeat the process "DRUM ENTRANCE/EXIT" (See page 31).
X-POSITION TEST POINTS MEASURING EQUIPMENT ADJUSTMENT
S/W PULSE TEST PIN ENVELOPE TEST PIN OSCILLOSCOPE VR CONTROL ADJUST BOSS
1) 2) 3) 4) 5)
PATH ADJ. JIG PATH ADJ. JIG PATH ADJ. JIG MAIN BASE
Connect the PATH ADJ. JIG to PTO1 of the MAIN CIRCUIT BOARD. Play back the ALIGNMENT TAPE (COLOUR SIGNAL BAR). Connect the channel-1 scope probe to the S/W PULSE TEST PIN of the PATH ADJ. JIG. Connect the channel-2 scope probe to the ENVELOPE TEST PIN of the PATH ADJ. JIG. Adjust the VR CONTROL to the centre position. (When the VR CONTROL is rotated completely anti-clockwise, it is set at another tracking centre position. 6) When the VR CONTROL is fully rotated clockwise or anti-clockwise, turn the ADJUST BOSS of the MAINBASE and adjust the X-POSITION for the envelope waveform to be shown as in the figure below. 7) Repeat the process "PLAYBACK PHASE ADJUSTMENT" (See page 29).
X-position adjustment Fig.52
33
cp421vbl.sch-1 - Wed May 19 17:22:44 1999
VIDEO BLOCK DIAGRAM
cp421abl.sch-1 - Wed May 19 17:19:52 1999
AUDIO BLOCK DIAGRAM
cp421pbl1.sch-1 - Wed May 19 17:21:31 1999
POWER BLOCK DIAGRAM
PARTS LOCATION T.V. NOTE: The numbers on the exploded view below refer to the mechanical section of the Replacement Parts List.
25 20 7 23 10 18
6 16 17 15 14
9
26 21 8
1 12 22
19
13 24 11
3
2
5
4
37
REPLACEMENT PARTS LIST Important Safety Notice Components Identified by mark have special characteristics important for safety. * When replacing any of these components, use only manufacturers specified parts. In case of ordering these spare parts, please always add the complete Model-Type number to your order.
Cct Ref
Parts Number
Description
COMMON PARTS MECHANICAL PARTS
Cct Ref
Parts Number
Description
I901
TDA6106Q
RGB DRIVE
I902 I903
TDA6106Q TDA6106Q
RGB DRIVE RGB DRIVE
IN01 IN02
M37777EFQ KA7533Z
VCR MICRO REGULATOR
1 2
4851930400 4851936300
DECK ASSEMBLY CHASSIS FRAME ASSY
IN03 IN04
BA6209(ROHM) MN1280R
MOTOR DRIVE RESET
3 4
4852716000 4852822201
SET FOOT DOOR ASSEMBLY
IQ01 IY01
KRT30 LA71511M
PREAMP VCR SIGNAL PROCESSOR
5 6
4854855801 4856013301
POWER BUTTON CRT SCREWS TOP
IY02 IY04
LC89977M LA70011 (4HD
CCD PROCESSOR PRE AMP
7 8
4856013303 4857242000
CRT SCREWS BOTTOM SHIELD COVER
SN01 SN02
SG-239S SG-239S
SENSOR SENSOR
9 10
4857242900 4859905110
CHASSIS TOP COVER POWER CORD
FUSES
11
4944001+5540
CONTROL BUTTON ASS.
5FSCB4022R
FUSE 4A250V
F801
12
DT5-BF15P,
TUNER (VCR)
DIODES
13 14
DT5-BF15P. EUR51941
TUNER (T.V.) REMOTE CONTROL
D106 D111
D1N4003 DUZ5R1BM
DIODE DIODE
15
UR51EC780
BATTERY COVER (REMOTE)
D114 D301
DUZ9R1BM DRGP15J
DIODE DIODE
D302 D401
DRGP15J DRGP15J
DIODE DIODE
D402 D403
DRGP15J D1N4148
DIODE DIODE
MISCELLANEOUS COMPONENTS .
4850M04510
RF MODULE
.
4856715600
POWER BUTTON SPRING
D405 D406
D1N4148 D1N4148
DIODE DIODE
. .
4856723400 UM-3DJ-2P
DOOR ASSEMBLY SPRING BATTERY PACK
D502 D504
D1N4148 D1N4148
DIODE DIODE
M351 M392
4853535400 4853948400
LED HOLDER EARTH BRACKET
D507 D508
D1N4148 DUZ6R2BM
DIODE DIODE
M791
4857913304
RUBBER SPONGE
D509 D510
DUZ12BM DUZ6R2BM
DIODE DIODE
ENGLISH
D511
DUZ6R2BM
DIODE
I.C.s
D512
DUZ6R2BM
DIODE
D819
KIA7812PI
REGULATOR
I201 I301
TDA9800 TDA8356
IF PROCESSOR VERTICAL OUTPUT
D513 D514
DUZ6R2BM DUZ6R2BM
DIODE DIODE
I501 I504
TDA8844/N2 TC4053BP
VIDEO PROCESSOR SWITCHING IC
D515 D516
DUZ6R2BM DUZ12BM
DIODE DIODE
I505 I506
KA7808 TC4066BP
REGULATOR SWITCHING IC
D517 D701
D1N4148 D1N4148
DIODE DIODE
I601
TDA1519B
AUDIO AMP
D702 D703
D1N4148 D1N4148
DIODE DIODE
I701
SD545X0TP
MAIN MICRO
I702 I703
MN1280R AT24C08-10PC
RESET MEMORY
D704 D705
D1N4148 D1N4148
DIODE DIODE
I801 I802
STR-S5707 KIA7812PI
POWER SUPPLY REGULATOR
D706 D707
D1N4148 DUZ9R1BM
DIODE DIODE
I804 I805
KIA7812PI KIA7806PI
REGULATOR REGULATOR
D709 D710
D1N4148 D1N4148
DIODE DIODE
I806 I807
KIA7806PI TOP210
REGULATOR STANDBY
D711 D801
D1N4148 D1S1888
DIODE DIODE
D802
D1S1888
DIODE
I808
PQ12RF11
REGULATOR
D803
D1S1888
DIODE
INSTRUCTION BOOKS .
TQB8E2911
38
Cct Ref
Parts Number
Description
Cct Ref
D804
D1S1888
DIODE
QC701
2SC1623-L6/T
TRANSISTOR
D807 D808
DRGP15J DRGP15J
DIODE DIODE
QC703 QC705
2SC1623-L6/T 2SC1623-L6/T
TRANSISTOR TRANSISTOR
D809 D810
DRGP15J DRGP15J
DIODE DIODE
QC706 QCL06
2SC1623-L6/T 2SC1623-L6/T
TRANSISTOR TRANSISTOR
D811 D812
DRGP30J DRGP30J
DIODE DIODE
QCN02 QCN03
2SC1623-L6/T 2SC1623-L6/T
TRANSISTOR TRANSISTOR
D813 D814
DRGP15J DRGP15J
DIODE DIODE
QCY01 QCY02
2SC1623-L6/T 2SA812-T2B
TRANSISTOR TRANSISTOR
D815 D822
DRGP30J DRU1P
DIODE DIODE
QCY03 QCY05
2SC1623-L6/T 2SA812-T2B
TRANSISTOR TRANSISTOR
D823
D1N4148
DIODE
QCY07
2SC1623-L6/T
TRANSISTOR
D824
DR2KY
AVALANCHE DIODE
QCY08
2SC1623-L6/T
TRANSISTOR
D825 D826
D1S1888 D1S1888
DIODE DIODE
QCY09 QCY10
2SA812-T2B 2SC1623-L6/T
TRANSISTOR TRANSISTOR
D827 D828
D1S1888 D1S1888
DIODE DIODE
QCY11 QCY12
2SC1623-L6/T 2SC1623-L6/T
TRANSISTOR TRANSISTOR
D830 D831
D1N4003 DRGP30J
DIODE DIODE
QCY13 QCY14
2SA812-T2B 2SC1623-L6/T
TRANSISTOR TRANSISTOR
D901 D902
D1N4148 D1N4148
DIODE DIODE
QCY15 QCY16
2SC1623-L6/T 2SC1623-L6/T
TRANSISTOR TRANSISTOR
D903 D904
D1N4148 D1N4148
DIODE DIODE
QCY17 QCY18
2SA812-T2B 2SC1623-L6/T
TRANSISTOR TRANSISTOR
DA01 DA02
DUZ6R2BM D1N4148
DIODE DIODE
QCY19 QQ02
2SC1623-L6/T KTC3198Y
TRANSISTOR TRANSISTOR
DA03 DN01
DMTZ6R2B DS15312H
DIODE LED IR
QQ03 QQ04
KTC3198Y KTC3198Y
TRANSISTOR TRANSISTOR
DN02 DN03
D1N4003 D1N4003
DIODE DIODE
QQ05 QQ06
KTC3198Y KTC3198Y
TRANSISTOR TRANSISTOR
DN05
DUZ6R2BM
DIODE
QY04
KTC3202Y (TP
TRANSISTOR
DN07
D1N4148
DIODE
QY06
KTC3198Y
TRANSISTOR
DN08 DN09
D1N4148 D1N4003
DIODE DIODE
SN03 SN04
ST-5811 ST-5811
TRANSISTOR TRANSISTOR
DQ01 DQ02
DSR54MVW3 DSR54MVW3
LED LED
T802
50MST22A3J
TRANSISTOR
TRANSFORMERS
DQ03 DQ04
DSR54MVW3 DUZ6R2BM
LED DIODE
T401
50D0000022
TRANSFORMER
T402
50H0000201
F.B.T.
DQ05 DQ06
DUZ6R2BM DUZ6R2BM
DIODE DIODE
COILS
DQ07 DY02
D1N4148 D1N4148
DIODE DIODE
L201 L202
58B0000S88 5CPZ150K02
COIL PEAKING COIL
DY03 DY05
D1N4148 D1N4148
DIODE DIODE
L203 L301
5CPZ100K02 5CPZ100K04
PEAKING COIL PEAKING COIL
DY06 R801
D1N4148 DEC140M290
DIODE DIODE
L302 L401
5CPZ100K04 5CPZ109M02
PEAKING COIL PEAKING COIL
L403 L501
58C0000096 5CPZ100K02
COIL PEAKING COIL
L502
5CPZ100K04
PEAKING COIL
L503
5CPZ100K04
PEAKING COIL
L505 L506
5CPZ220K02 5CPZ150K02
PEAKING COIL PEAKING COIL
L601 L604
5CPZ100K04 58C6R8J067
PEAKING COIL COIL
L702 L704
5CPZ101K04 5CPZ101K04
PEAKING COIL PEAKING COIL
LA01 LY01
5CPZ100K04 5CPZ101K04
PEAKING COIL PEAKING COIL
LY03 LY04
5CPZ101K04 5CPZ100K04
PEAKING COIL PEAKING COIL
LY05 LY06
5CPZ101K04 5CPZ560K02
PEAKING COIL PEAKING COIL
LY07 LY10
5CPZ121K02 5CPZ101K04
PEAKING COIL PEAKING COIL
LY12 LY13
5CPX103J 5CPZ221K02
PEAKING OIL PEAKING COIL
TY01
5800000032
COIL
TRANSISTORS Q301
KTC3198Y
TRANSISTOR
Q401
KTC3207 (TP)
TRANSISTOR
Q402 Q403
2SD2499 KTC3203-Y
TRANSISTOR TRANSISTOR
Q601 Q803
KTC3198Y KTC3203-Y
TRANSISTOR TRANSISTOR
Q901 QC102
KTA1266Y (TP 2SA812-T2B
TRANSISTOR TRANSISTOR
QC205 QC501
2SC1623-L6/T 2SC1623-L6/T
TRANSISTOR TRANSISTOR
QC502 QC503
2SC1623-L6/T 2SC1623-L6/T
TRANSISTOR TRANSISTOR
QC504 QC505
2SC1623-L6/T 2SC1623-L6/T
TRANSISTOR TRANSISTOR
QC506 QC510
2SC1623-L6/T 2SA812-T2B
TRANSISTOR TRANSISTOR
QC511 QC512
2SA812-T2B 2SA812-T2B
TRANSISTOR TRANSISTOR
QC515
2SA812-T2B
TRANSISTOR
QC602
2SC1623-L6/T
TRANSISTOR
Parts Number
Description
Cct Ref
Parts Number
Description
L801
5PLF24A1
LINE FILER
SF01 SF03
5PJ1952M 5PJ1952M
SAW FILTR SAW FILTR
Z204 Z502
5PXFSH6R0M 5PXFSH6R0M
FILTER FILTER
Z504
5PTPS60MB
FILTER
Cct Ref
FILTERS
CRYSTALS X501 X502
Parts Number
Description
R565
RD-AZ561J
CARBON
0.17W
5%
560
R573 R576
RD-AZ103J RD-AZ681J
CARBON CARBON
0.17W 0.17W
5% 5%
10K 680
R580 R585
RF-2Y100J RD-AZ222J
FUSIBLE CARBON
0.5W 0.7W
5% 5%
10 2.2K
R601 R602
RD-4Z221J RD-4Z221J
CARBON CARBON
0.25W 0.25W
5% 5%
220 220
R603 R701
RD-AZ102J RD-4Z100J
CARBON CARBON
0.17W 0.25W
5% 5%
1K 10 100 100
5XEX3R579C 5XEX4R436C
CRYSTAL CRYSTAL
R713 R720
RD-AZ101J RD-AZ101J
CARBON CARBON
0.17W 0.17W
5% 5%
X701
5XE6R0000C
CRYSTAL
R721
RD-AZ101J
CARBON
0.17W
5%
100
XN02
5XJ16R000E
CRYSTAL
R728
RD-AZ472J
CARBON
0.17W
5%
4.7K
XNC01 XY02
HXA32R768C 5XJX4R433B
CRYSTAL CRYSTAL
R747 R748
RD-4Z561J RD-AZ272J
CARBON CARBON
0.25W 0.7W
5% 5%
560 2.7K
R749 R750
RD-AZ272J RD-AZ272J
CARBON CARBON
0.7W 0.7W
5% 5%
2.7K 2.7K
R773 R782
RD-AZ103J RD-AZ273J
CARBON CARBON
0.17W 0.17W
5% 5%
10K 27K
R783 R803
RD-AZ101J RX10T339J
CARBON WOUND
0.17W 10W
5% 5%
100 3.3
R804 R805
RS02Z473JS RS02Z562JS
METAL METAL
2W 2W
5% 5%
47K 5.6K
R807 R808
RD-4Z330J RD-4Z222J
CARBON CARBON
0.25W 0.25W
5% 5%
33 2.2K
R810 R811
RD-4Z104J RD-AZ102J
CARBON CARBON
0.25W 0.17W
5% 5%
100K 1K
R812 R813
RD-2Z224J RD-2Z224J
CARBON CARBON
0.5W 0.5W
5% 5%
220K 220K
R815
RC-2Z565KP
CARBON
0.5W 10%
5.6M
R816
RS02Z470JS
METAL
R817 R819
RF02Z338KRD-2Z104J
FUSIBLE CARBON
R823 R830
RS02Z562JS RS02Z109JS
METAL METAL
R831 R836
RD-4Z270J RD-4Z270J
R843 R907
RESISTORS CCL33 J214
HRFT000-CA RD-AZ153J
S.M.CARB CARBON
0.1W 0.17W
5% 5%
0 15K
J215 J216
RD-AZ153J RD-AZ153J
CARBON CARBON
0.17W 0.17W
5% 5%
15K 15K
J265
RD-AZ101J
CARBON
0.17W
5%
100
J277
RD-AZ151J
CARBON
0.17W
5%
150
LY09 R101
RD-2Z109J RD-2Z150J
CARBON CARBON
0.5W 0.5W
5% 5%
1 15
R102 R112
RD-AZ392J RD-AZ681J
CARBON CARBON
0.17W 0.17W
5% 5%
3.9K 680
R121 R202
RS02Z470JS RV5221103
METAL FIXED
2W
5%
47
R219 R242
RD-AZ392J RD-AZ822J
CARBON CARBON
0.17W 0.33W
5% 5%
3.9K 8.2K
R302 R304
RD-4Z472J RD-2Z109J
CARBON CARBON
0.25W 0.5W
5% 5%
4.7K 1
R306 R310
RS02Z271JS RD-4Z471J
METAL CARBON
2W 0.25W
5% 5%
270 470
R311 R312
RD-AZ332J RD-AZ223J
CARBON CARBON
0.17W 0.17W
5% 5%
3.3K 22K
R313 R314
RD-4Z472J RD-4Z473J
CARBON CARBON
0.25W 0.25W
5% 5%
4.7K 47K
R315 R401
RD-4Z229J RS02Z912JS
CARBON METAL
0.25W 2W
5% 5%
2.2 9.1K
R402 R403
RS02Z912JS RS02Z912JS
METAL METAL
2W 2W
5% 5%
9.1K 9.1K
R404 R406
RD-AZ472J RD-4Z562J
CARBON CARBON
0.17W 0.25W
5% 5%
4.7K 5.6K
R407 R408
RS02Z512JS RD-4Z102J
METAL CARBON
2W 0.25W
5% 5%
5.1K 1K
R409
RS02Z512JS
METAL
2W
5%
5.1K
R410
RD-2Z104J
CARBON
0.5W
5%
100K
R412 R413
RD-2Z273J RD-4Z303J
CARBON CARBON
0.5W 0.25W
5% 5%
27K 30K
R415 R418
RD-2Z224J RD-2Z103J
CARBON CARBON
0.5W 0.5W
5% 5%
220K 10K
R420 R421
RS01Z102J RD-4Z472J
METAL CARBON
1W 0.25W
5% 5%
1K 4.7K
R422 R504
RD-AZ152J RD-4Z109J
CARBON CARBON
0.17W 0.25W
5% 5%
1.5K 1
R506 R516
RD-4Z109J RD-AZ102J
CARBON CARBON
0.25W 0.17W
5% 5%
1 1K
R517 R525
RD-AZ101J RD-AZ102J
CARBON CARBON
0.17W 0.17W
5% 5%
100 1K
R529 R540
RD-AZ102J RD-AZ103J
CARBON CARBON
0.17W 0.17W
5% 5%
1K 10K
R549 R550
RD-AZ221J RD-AZ221J
CARBON CARBON
0.17W 0.17W
5% 5%
220 220
R563
RD-AZ473J
CARBON
0.17W
5%
R564
RD-AZ303J
CARBON
0.17W
5%
2W
5%
47
2W 10% 0.5W 5%
0.33 100K
2W 2W
5% 5%
5.6K 1
CARBON CARBON
0.25W 0.25W
5% 5%
27 27
RD-AZ472J RD-4Z104J
CARBON CARBON
0.17W 0.25W
5% 5%
4.7K 100K
R908 R909
RD-4Z104J RD-4Z104J
CARBON CARBON
0.25W 0.25W
5% 5%
100K 100K
R910 R911
RD-2Z152J RD-2Z152J
CARBON CARBON
0.5W 0.5W
5% 5%
1.5K 1.5K
R912 R913
RD-2Z152J RD-AZ223J
CARBON CARBON
0.5W 0.17W
5% 5%
1.5K 22K
R914 RA01
RD-AZ152J RD-AZ752J
CARBON CARBON
0.17W 0.17W
5% 5%
1.5K 7.5K
RC105 RC201
HRFT472JCA HRFT182JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
4.7K 1.8K
RC204 RC205
HRFT302JCA HRFT271JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
3K 270
RC207 RC208
HRFT223JCA HRFT223JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
22K 22K
RC224 RC230
HRFT681JCA HRFT152JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
680 1.5K
RC231
HRFT102JCA
S.M.CARB
0.1W
5%
1K
RC232
HRFT753JCA
S.M.CARB
0.1W
5%
75K
RC233 RC235
HRFT102JCA HRFT681JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1K 680
RC236 RC238
HRFT471JCA HRFT154JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
470 150K
RC239 RC503
HRFT242JCA HRFT683JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
2.4K 68K
47K
RC507 RC509
HRFT683JCA HRFT391JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
68K 390
30K
RC510
HRFT301JCA
S.M.CARB
0.1W
5%
300
39
Cct Ref
Parts Number
Description
Cct Ref
RC511
HRFT301JCA
S.M.CARB
0.1W
5%
300
RC730
HRFT332JCA
S.M.CARB
0.1W
5%
3.3K
RC512 RC513
HRFT680JCA HRFT301JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
68 300
RC732 RC733
HRFT103JCA HRFT103JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
10K 10K
RC514 RC515
HRFT750JCA HRFT430JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
75 43
RC736 RC737
HRFT272JCA HRFT273JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
2.7K 27K
RC518 RC520
HRFT101JCA HRFT101JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
100 100
RC740 RC744
HRFT103JCA HRFT103JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
10K 10K
RC521 RC522
HRFT101JCA HRFT101JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
100 100
RC775 RC776
HRFT472JCA HRFT472JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
4.7K 4.7K
RC523 RC526
HRFT151JCA HRFT102JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
150 1K
RC777 RC778
HRFT472JCA HRFT472JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
4.7K 4.7K
RC527
HRFT102JCA
S.M.CARB
0.1W
5%
1K
RC780
HRFT473JCA
S.M.CARB
0.1W
5%
47K
RC528
HRFT102JCA
S.M.CARB
0.1W
5%
1K
RC781
HRFT472JCA
S.M.CARB
0.1W
5%
4.7K
RC530 RC531
HRFT103JCA HRFT152JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
10K 1.5K
RCJ01 RCJ02
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC532 RC533
HRFT102JCA HRFT102JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1K 1K
RCJ03 RCJ04
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC534 RC536
HRFT561JCA HRFT103JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
560 10K
RCJ05 RCJ06
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC538 RC539
HRFT822JCA HRFT103JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
8.2K 10K
RCJ07 RCJ11
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC543 RC544
HRFT104JCA HRFT182JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
100K 1.8K
RCJ12 RCJ14
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC545 RC546
HRFT153JCA HRFT153JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
15K 15K
RCJ17 RCJ21
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC547 RC548
HRFT154JCA HRFT153JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
150K 15K
RCJ22 RCJ23
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC552 RC553
HRFT153JCA HRFT102JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
15K 1K
RCJ24 RCJ25
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC554
HRFT333JCA
S.M.CARB
0.1W
5%
33K
RCJ29
HRFT000-CA
S.M.CARB
0.1W
5%
0
RC556
HRFT331JCA
S.M.CARB
0.1W
5%
330
RCJ31
HRFT000-CA
S.M.CARB
0.1W
5%
0
RC557 RC558
HRFT391JCA HRFT182JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
390 1.8K
RCJ32 RCJ35
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC559 RC560
HRFT472JCA HRFT393JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
4.7K 39K
RCJ36 RCJ37
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC562 RC566
HRFT471JCA HRFT101JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
470 100
RCJ38 RCJ39
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC567 RC568
HRFT562JCA HRFT681JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
5.6K 680
RCJ40 RCJ41
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC569 RC574
HRFT270JCA HRFT241JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
27 240
RCJ42 RCJ43
HRFT000-CA HRFT102JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 1K
RC577 RC578
HRFT470JCA HRFT221JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
47 220
RCJ44 RCJ45
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC581 RC582
HRFT272JCA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
2.7K 0
RCJ47 RCJ48
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC584 RC601
HRFT223JCA HRFT112JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
22K 1.1K
RCJ50 RCJ51
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC603 RC604
HRFT563JCA HRFT472JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
56K 4.7K
RCJ52 RCJ53
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC605 RC703
HRFT472JCA HRFT103JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
4.7K 10K
RCJ54 RCJ55
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC704 RC705
HRFT392JCA HRFT472JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
3.9K 4.7K
RCJ56 RCJ57
HRFT000-CA HRFT000-CA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 0
RC706 RC707
HRFT332JCA HRFT332JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
3.3K 3.3K
RCJ58 RCL37
HRFT000-CA HRFT472JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
0 4.7K
RC711
HRFT221JCA
S.M.CARB
0.1W
5%
220
RCL38
HRFT103JCA
S.M.CARB
0.1W
5%
10K
RC712
HRFT221JCA
S.M.CARB
0.1W
5%
220
RCN01
HRFT474JCA
S.M.CARB
0.1W
5%
470K
RC715 RC717
HRFT105JCA HRFT103JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1M 10K
RCN07 RCN09
HRFT103JCA HRFT332JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
10K 3.3K
RC718 RC719
HRFT101JCA HRFT101JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
100 100
RCN10 RCN11
HRFT103JCA HRFT103JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
10K 10K
RC722 RC723
HRFT102JCA HRFT162JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1K 1.6K
RCN20 RCN23
HRFT103JCA HRFT154JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
10K 150K
RC724 RC725
HRFT162JCA HRFT162JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1.6K 1.6K
RCN24 RCN27
HRFT154JCA HRFT105JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
150K 1M
RC729
HRFT473JCA
S.M.CARB
0.1W
5%
47K
RCN31
HRFT182JCA
S.M.CARB
0.1W
5%
1.8K
40
Parts Number
Description
Cct Ref
Parts Number
Description
Cct Ref
RCN32
HRFT182JCA
S.M.CARB
0.1W
5%
1.8K
RCY70
HRFT104JCA
S.M.CARB
0.1W
5%
100K
RCN34 RCN40
HRFT333JCA HRFT104JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
33K 100K
RCY71 RCY72
HRFT104JCA HRFT103JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
100K 10K
RCN41 RCN45
HRFT106JCA HRFT302JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
10M 3K
RCY74 RCY75
HRFT154JCA HRFT154JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
150K 150K
RCN51 RCN52
HRFT511FCA HRFT472JCA
S.M.CARB S.M.CARB
0.1W 0.1W
1% 5%
510 4.7K
RCY77 RCY78
HRFT223JCA HRFT273JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
22K 27K
RCN60 RCQ04
HRFT103JCA HRFT132JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
10K 1.3K
RCY79 RCY80
HRFT104JCA HRFT104JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
100K 100K
RCQ05 RCQ06
HRFT132JCA HRFT161JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1.3K 160
RCY81 RCY82
HRFT103JCA HRFT222JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
10K 2.2K
RCQ07
HRFT161JCA
S.M.CARB
0.1W
5%
160
RCY83
HRFT471JCA
S.M.CARB
0.1W
5%
470
RCQ09
HRFT221JCA
S.M.CARB
0.1W
5%
220
RCY84
HRFT473JCA
S.M.CARB
0.1W
5%
47K
RCQ10 RCQ11
HRFT221JCA HRFT202JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
220 2K
RN08 RN12
RD-AZ682J RD-AZ103J
CARBON CARBON
0.17W 0.17W
5% 5%
6.8K 10K
RCQ13 RCQ14
HRFT361JCA HRFT511FCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 1%
360 510
RN13 RN14
RD-AZ103J RD-AZ103J
CARBON CARBON
0.17W 0.17W
5% 5%
10K 10K
RCQ16 RCQ17
HRFT361JCA HRFT221JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
360 220
RN15 RN19
RD-AZ103J RD-AZ103J
CARBON CARBON
0.17W 0.17W
5% 5%
10K 10K
RCY01 RCY02
HRFT242JCA HRFT152JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
2.4K 1.5K
RN20 RN21
RD-AZ472J RD-AZ301J
CARBON CARBON
0.17W 0.17W
5% 5%
4.7K 300
RCY03 RCY04
HRFT472JCA HRFT102JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
4.7K 1K
RN22 RN25
RD-AZ301J RD-AZ273J
CARBON CARBON
0.17W 0.17W
5% 5%
300 27K
RCY05 RCY07
HRFT472JCA HRFT102JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
4.7K 1K
RN26 RN29
RD-AZ273J RD-AZ182J
CARBON CARBON
0.17W 0.17W
5% 5%
27K 1.8K
RCY08 RCY09
HRFT102JCA HRFT123JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1K 12K
RN33 RN35
RD-AZ153J RD-AZ221J
CARBON CARBON
0.17W 0.17W
5% 5%
15K 220
RCY10 RCY11
HRFT102JCA HRFT823JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1K 82K
RN36 RN38
RD-AZ221J RD-AZ101J
CARBON CARBON
0.17W 0.17W
5% 5%
220 100
RCY13
HRFT152JCA
S.M.CARB
0.1W
5%
1.5K
RN39
RD-AZ101J
CARBON
0.17W
5%
100
RCY15
HRFT271JCA
S.M.CARB
0.1W
5%
270
RN43
RD-AZ332J
CARBON
0.17W
5%
3.3K
RCY16 RCY17
HRFT822JCA HRFT822JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
8.2K 8.2K
RN44 RN46
RD-AZ332J RD-AZ102J
CARBON CARBON
0.17W 0.17W
5% 5%
3.3K 1K
RCY18 RCY19
HRFT182JCA HRFT202JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1.8K 2K
RN47 RN48
RD-AZ102J RD-AZ102J
CARBON CARBON
0.17W 0.17W
5% 5%
1K 1K
RCY20 RCY23
HRFT202JCA HRFT132JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
2K 1.3K
RN53 RN56
RS02Z399JS RD-AZ472J
METAL CARBON
2W 0.17W
5% 5%
3.9 4.7K
RCY24 RCY25
HRFT471JCA HRFT152JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
470 1.5K
RN57 RN58
RD-AZ472J RD-AZ472J
CARBON CARBON
0.17W 0.17W
5% 5%
4.7K 4.7K
RCY26 RCY30
HRFT223JCA HRFT102JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
22K 1K
RN59 RN70
RD-AZ472J RD-AZ472J
CARBON CARBON
0.17W 0.17W
5% 5%
4.7K 4.7K
RCY32 RCY33
HRFT103JCA HRFT333JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
10K 33K
RQ01 RQ03
RD-AZ271J RD-AZ271J
CARBON CARBON
0.17W 0.17W
5% 5%
270 270
RCY34 RCY35
HRFT272JCA HRFT242JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
2.7K 2.4K
RQ08 RQ12
RD-AZ271J RD-AZ112J
CARBON CARBON
0.17W 0.17W
5% 5%
270 1.1K
RCY36 RCY37
HRFT202JCA HRFT822JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
2K 8.2K
RQ13 RQ15
RD-AZ102J RD-AZ221J
CARBON CARBON
0.17W 0.17W
5% 5%
1K 220
RCY38 RCY39
HRFT511JCA HRFT472JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
510 4.7K
RQ19 RQ20
RD-AZ271J RD-AZ153J
CARBON CARBON
0.17W 0.17W
5% 5%
270 15K
RCY40 RCY41
HRFT183JCA HRFT225JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
18K 2.2M
RY05 RY06
RD-AZ102J RD-AZ102J
CARBON CARBON
0.17W 0.17W
5% 5%
1K 1K
RCY42 RCY43
HRFT102JCA HRFT562JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1K 5.6K
RY12 RY21
RD-AZ182J RD-AZ229J
CARBON CARBON
0.17W 0.17W
5% 5%
1.8K 2.2
RCY44 RCY45
HRFT221JCA HRFT391JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
220 390
RY22 RY27
RD-AZ229J RD-AZ333J
CARBON CARBON
0.17W 0.17W
5% 5%
2.2 33K
RCY48
HRFT331JCA
S.M.CARB
0.1W
5%
330
RY28
RD-AZ513J
CARBON
0.17W
5%
51K
RCY50
HRFT334JCA
S.M.CARB
0.1W
5%
330K
RY29
RD-AZ303J
CARBON
0.17W
5%
30K
RCY51 RCY52
HRFT302JCA HRFT122JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
3K 1.2K
RY31 RY46
RD-AZ513J RD-AZ391J
CARBON CARBON
0.17W 0.17W
5% 5%
51K 390K
RCY53 RCY55
HRFT122JCA HRFT103JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
1.2K 10K
RY47 RY48
RD-AZ561J RD-AZ820J
CARBON CARBON
0.17W 0.17W
5% 5%
560 82
RCY56 RCY57
HRFT512JCA HRFT103JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
5.1K 10K
RY54 RY58
RD-AZ122J RD-AZ151J
CARBON CARBON
0.17W 0.17W
5% 5%
1.2K 150
RCY59 RCY60
HRFT470JCA HRFT271JCA
S.M.CARB S.M.CARB
0.1W 0.1W
5% 5%
47 270
RY73 RY76
RD-AZ103J RD-AZ332J
CARBON CARBON
0.17W 0.17W
5% 5%
10K 3.3K
RCY61
HRFT271JCA
S.M.CARB
0.1W
5%
270
41
Parts Number
Description
Cct Ref
Parts Number
Description
Cct Ref
CAPACITORS C107
CEXF1H100V
ELECT
50V
)
C120 C225
CEXD1H109F CEXF1H220V
ELECT ELECT
50V 50V
)
C226 C227
CEXF1H100V CEXF1H109V
ELECT ELECT
50V 50V
)
C230 C233
CEXF1C471V CEXF1E101V
ELECT ELECT
16V 25V
)
C237 C301
CEXF1E331V CCZB1H102K
ELECT CERAMIC
25V 50V
)
)
)
)
Q)
C302
CCZB1H102K
CERAMIC
50V
Q)
C305
CCXB2H471K
CERAMIC
500V
S)
C306 C307
CCXB2H102K CEXF2C220V
CERAMIC ELECT
500V 160V
C308 C309
CEXF1E471V CCZF1H103Z
ELECT CERAMIC
25V 50V
Q) ) ) Q)
C310 C311
CMXM2A104J CMXM2A103J
MYLAR MYLAR
100V 100V
C312 C313
CMXM2A102J CMXM2A104J
MYLAR MYLAR
100V 100V
C401 C402
CCXB2H472K CCXB2H221K
CERAMIC CERAMIC
500V 500V
S)
C403 C404
CCXB2H472K CCXB2H102K
CERAMIC CERAMIC
500V 500V
S)
Q) Q) Q) Q)
S)
Q)
C406 C407
CCXB3D471K CXSL2H470J
CERAMIC CERAMIC
2kV 500V
S)
C409 C410
CEXF2C220V CEXF2C109V
ELECT ELECT
160V 160V
)
C413
CEXF2E330V
ELECT
250V
)
C418
CMXL2E104K
MYLAR
C526 C543
CCZB1H151K CEXF1H229V
CERAMIC ELECT
C546 C547
CMXM2A104J CMXM2A473J
C548 C553
S)
)
250V
Q)
50V 50V
S)
MYLAR MYLAR
100V 100V
Q)
CMXM2A104J CEXF1H100V
MYLAR ELECT
100V 50V
Q)
C556 C557
CEXF1E470V CEXF1E470V
ELECT ELECT
25V 25V
)
C559 C560
CEXF1E470V CEXF1E470V
ELECT ELECT
25V 25V
)
C564 C565
CEXF1E101V CEXF1E101V
ELECT ELECT
25V 25V
)
)
Q)
)
)
)
)
C566 C567
CEXF1C102V CEXF1C102V
ELECT ELECT
16V 16V
)
C570 C571
CEXF1E101V CEXF1H478V
ELECT ELECT
25V 50V
)
C580
CBZR1C472M
CERAMIC
16V
S)
C583
CEXF1E101V
ELECT
25V
)
C591 C609
CEXF1E101V CEXF1H220V
ELECT ELECT
25V 50V
)
C610 C611
CEXF1E471C CEXF1E470V
ELECT ELECT
25V 25V
)
C613 C614
CMXB1H224J CEXF1H470V
MYLAR ELECT
50V 50V
Q)
C711 C719
CCZF1H103Z CEXF1C470A
CERAMIC ELECT
50V 16V
Q)
C720 C721
CEXF1A471V CEXF1C101A
ELECT ELECT
10V 16V
)
C722 C723
CEXF1A471V CEXF1C101A
ELECT ELECT
10V 16V
)
C724 C801
CEXF1E221V CL1JB3474K
ELECT FILM
25V 250V
)
C803 C804
CCXF3A472Z CCXF3A472Z
CERAMIC CERAMIC
1kV 1kV
S)
C807
CCZB1H102K
CERAMIC
50V
Q)
C808
CH1AFE472M
CERAMIC
4kV
S)
)
Q)
)
)
)
)
)
)
Q)
S)
Parts Number
Description
C810
CCXB3D681K
CERAMIC
2kV
S)
C813 C816
CCXF1H103Z CEXF2A100V
CERAMIC ELECT
50V 100V
Q)
C817 C818
CEXF1E221C CEXF1E331V
ELECT ELECT
25V 25V
)
C819 C820
CEYN2G181P CEYF2C221V
ELECT ELECT
400V 160V
)
C822 C823
CEXF1C102C CEXF2G220V
ELECT ELECT
16V 400V
)
C824 C825
CEXF1H470V CEXF1C102V
ELECT ELECT
50V 16V
C826
CEXF1E101C
ELECT
25V
)
C827
CEXF1E102C
ELECT
25V
)
C828 C829
CEXF1E471V CEXF1E101C
ELECT ELECT
25V 25V
)
C830 C832
CEXF1E221V CEXF1C102C
ELECT ELECT
25V 16V
C833 C834
CEXF1C102C CEXF1E221C
ELECT ELECT
16V 25V
)
C835 C836
CMXE2J222J CBZF1H104Z
MYLAR CERAMIC
630V 50V
S)
C837 C838
CBZF1H104Z CBZF1H104Z
CERAMIC CERAMIC
50V 50V
Q)
C840 C841
CEXF1E470V CCXF3A472Z
ELECT CERAMIC
25V 1kV
C842 C846
CCXF3A472Z CCZF1H103Z
CERAMIC CERAMIC
1kV 50V
S)
C904 C905
CMXL2E104K CMXL2E104K
MYLAR MYLAR
250V 250V
Q)
C910
CCXF1H473Z
CERAMIC
50V
Q)
C911
CCXB3D102K
CERAMIC
2kV
Q)
C913 CC103
CEXF1C331V HCBK103KCA
ELECT S.M.CAP
16V 50V
)
CC104 CC105
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC118 CC119
HCQK221JCA HCQK221JCA
S.M.CAP S.M.CAP
50V 50V
S)
CC201 CC202
HCBK333KCA HCBK223KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC205 CC206
HCQK820JCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
S) Q)
CC208 CC209
HCBK103KCA HCBH224KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC210 CC212
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
CC213 CC214
HCBK102KCA HCQK560JCA
S.M.CAP S.M.CAP
50V 50V
CC215 CC219
HCQK220JCA HCQK809DCA
S.M.CAP CERAMIC
50V 50V
S)
CC220 CC221
HCBK472KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
S)
CC223 CC224
HCBK333KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC225 CC228
HCBK104KCA HCTAF229MB
S.M.CAP TANT
50V 16V
Q)
CC235
HCQK221JCA
S.M.CAP
50V
S)
CC236
HCQK221JCA
S.M.CAP
50V
S)
CC501 CC502
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC503 CC505
HCTAJ478MB HCTAJ478MB
TANT TANT
35V 35V
Q)
CC507 CC508
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC509 CC510
HCBK104KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC511
HCBK104KCA
S.M.CAP
50V
Q)
42
)
)
)
) ) )
) ) )
)
Q)
Q) ) S)
Q)
Q)
Q)
Q)
S)
Q)
Q)
Q) Q) Q) S)
S)
Q)
Q)
)
Q)
Q)
Q)
Q)
Cct Ref
Parts Number
Description
Cct Ref
CC512
HCBK103KCA
S.M.CAP
50V
Q)
CC725
HCBK103KCA
S.M.CAP
50V
Q)
CC513 CC517
HCBK104KCA HCBK102KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC727 CC728
HCBK103KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC518 CC520
HCBK102KCA HCBK102KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC729 CC730
HCTAH109MB HCQK471JCA
TANT S.M.CAP
25V 50V
CC523 CC524
HCQK160JCA HCQK130JCA
CERAMIC S.M.CAP
50V 50V
S)
CC731 CCL29
HCQK561JCA HCTBF100MB
S.M.CAP TANT
50V 16V
S)
CC525 CC526
HCQK181JCA HCQK181JCA
S.M.CAP S.M.CAP
50V 50V
S)
CCN01 CCN02
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC527 CC528
HCQK181JCA HCQK181JCA
S.M.CAP S.M.CAP
50V 50V
S)
HCBK103KCA HCBK102KCA
S.M.CAP S.M.CAP
50V 50V
Q)
S)
CCN07 CCN08
CC529
HCBK223KCA
S.M.CAP
50V
Q)
CCN09
HCBK103KCA
S.M.CAP
50V
Q)
CC532
HCQK220JCA
S.M.CAP
50V
S)
CCN10
HCBK103KCA
S.M.CAP
50V
Q)
CC533 CC534
HCBK392KCA HCBK472KCA
S.M.CAP S.M.CAP
50V 50V
S)
CCN11 CCN12
HCBK102KCA HCBK102KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC535 CC536
HCBK472KCA HCBK332KCA
S.M.CAP S.M.CAP
50V 50V
S)
CCN14 CCN15
HCBK103KCA HCBK332KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC537 CC538
HCQK560JCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
S)
CCN17 CCN20
HCBK104KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC539 CC540
HCQK221JCA HCTBF100MB
S.M.CAP TANT
50V 16V
S)
CCN21 CCN29
HCBK223KCA HCBK223KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC541 CC542
HCBK223KCA HCTAJ478MB
S.M.CAP TANT
50V 35V
Q)
CCN31 CCN37
HCBK104KCA HCTAH109MB
S.M.CAP TANT
50V 25V
Q)
CC544 CC549
HCQK100DCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
CCN44 CCN45
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC550 CC551
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CCN48 CCN49
HCBK104KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC552 CC554
HCTAF229MB HCTAF229MB
TANT TANT
16V 16V
)
HCBK104KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
)
CCN50 CCN52
CC561
HCTAF229MB
TANT
16V
)
CCN57
HCTBF100MB
TANT
16V
)
CC568
HCTAH109MB
TANT
25V
)
CCN58
HCTAH109MB
TANT
25V
)
CC569 CC572
HCTAH109MB HCTAJ478MB
TANT TANT
25V 35V
)
CCN60 CCQ01
HCQK100DCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
S)
CC573 CC576
HCBK102KCA HCBK472KCA
S.M.CAP S.M.CAP
50V 50V
CCY01 CCY02
HCBK103KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
CC581 CC582
HCBK102KCA HCBK102KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CCY03 CCY04
HCBK103KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
CC585 CC586
HCBK102KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CCY05 CCY06
HCBK223KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
CC587 CC589
HCBK103KCA HCBK102KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CCY07 CCY08
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC590 CC591
HCBK103KCA HCBK102KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CCY09 CCY11
HCBK104KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC601 CC602
HCBK102KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CCY14 CCY15
HCBK104KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC603 CC604
HCBK102KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
CCY16 CCY19
HCBH224KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC605 CC606
HCQK101JCA HCQK101JCA
S.M.CAP S.M.CAP
50V 50V
S)
CCY20 CCY21
HCBK103KCA HCBK223KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC607 CC608
HCBK102KCA HCBK102KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CCY22 CCY23
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC612 CC616
HCBK102KCA HCBK682KCA
S.M.CAP S.M.CAP
50V 50V
Q) S)
CCY24 CCY25
HCBK104KCA HCQK101JCA
S.M.CAP S.M.CAP
50V 50V
CC701 CC704
HCBK104KCA HCBK472KCA
S.M.CAP S.M.CAP
50V 50V
CCY26 CCY27
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
S)
CC705
HCBH224KCA
S.M.CAP
50V
Q)
CCY28
HCBK104KCA
S.M.CAP
50V
Q)
CC706
HCBK103KCA
S.M.CAP
50V
Q)
CCY29
HCBK104KCA
S.M.CAP
50V
Q)
CC707 CC708
HCQK330JCA HCQK330JCA
S.M.CAP S.M.CAP
50V 50V
S)
CCY30 CCY31
HCBK104KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC709 CC713
HCBK103KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CCY32 CCY33
HCBK153KCA HCQK101JCA
S.M.CAP S.M.CAP
50V 50V
CC715 CC716
HCBK103KCA HCQK221JCA
S.M.CAP S.M.CAP
50V 50V
CCY34 CCY35
HCBK103KCA HCBK473KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CC717 CC720
HCBK333KCA HCBK104KCA
S.M.CAP S.M.CAP
50V 50V
HCBK473KCA HCBK102KCA
S.M.CAP S.M.CAP
50V 50V
Q)
Q)
CCY36 CCY37
CC721
HCBK104KCA
S.M.CAP
50V
Q)
CCY38
HCBK472KCA
S.M.CAP
50V
S)
Q)
Q)
S)
S)
S)
S)
Q)
)
Q) S) Q)
Q)
Q) Q) S)
Q)
Q)
Q)
Q)
Q) Q) Q)
S)
Q)
Q)
S)
Q) Q) S) Q)
43
Parts Number
Description
Q) ) S)
)
Q)
Q)
Q)
S)
Q)
Q)
)
Q)
Q)
Q)
Q) Q) Q) Q) Q) Q) Q)
Q)
Q)
Q)
Q)
Q)
Q) Q) S)
Q)
Q) Q) S)
Q)
Q)
Cct Ref
Parts Number
Description
Cct Ref
CCY39
HCQK220JCA
S.M.CAP
50V
S)
CN56
CEXF1C470A
ELECT
16V
)
CCY41 CCY42
HCBK222KCA HCQK270JCA
S.M.CAP S.M.CAP
50V 50V
S)
CN59 CQ02
CDYF0H105K CEXF1H100V
CERAMIC ELECT
5.5V 50V
)
CCY43 CCY44
HCBK104KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CQ03 CY07
CEXF1E101V CCZF1H103Z
ELECT CERAMIC
25V 50V
)
CCY46 CCY47
HCQK201JCA HCBK333KCA
S.M.CAP S.M.CAP
50V 50V
S)
CY10 CY12
CMXM2A103J CCZF1H103Z
MYLAR CERAMIC
100V 50V
Q)
CCY48 CCY50
HCQK391JCA HCBK223KCA
S.M.CAP S.M.CAP
50V 50V
S)
CY13 CY17
CCZF1H103Z CCZF1H223Z
CERAMIC CERAMIC
50V 50V
Q)
CCY51 CCY52
HCBK103KCA HCQK101JCA
S.M.CAP S.M.CAP
50V 50V
Q) S)
CY18 CY40
CCZF1H103Z CMXM2A122J
CERAMIC MYLAR
50V 100V
CCY54
HCBK104KCA
S.M.CAP
50V
Q)
CY49
CMXM2A223J
MYLAR
100V
Q)
CCY55
HCBK103KCA
S.M.CAP
50V
Q)
CY53
CMXM2A122J
MYLAR
100V
S)
CCY56 CCY60
HCTBF100MB HCTAH109MB
TANT TANT
16V 25V
)
CY57 CY58
CEXF1H478A CEXF1H478A
ELECT ELECT
50V 50V
Q)
CCY61 CCY62
HCTAH109MB HCTAH109MB
TANT TANT
25V 25V
)
CY59 CY72
CMXM2A473J CEXF1C101A
MYLAR ELECT
100V 16V
)
CCY63 CCY64
HCTBH479MB HCTAH109MB
TANT TANT
25V 25V
)
CY73 CY78
CEXF1H109A CEXF1C220A
ELECT ELECT
50V 16V
)
CCY65 CCY66
HCTAH109MB HCTAH109MB
TANT TANT
25V 25V
)
CY80 CY81
CEXF1C101A CEXF1C101A
ELECT ELECT
16V 16V
)
CCY67 CCY68
HCTAH109MB HCTBF100MB
TANT TANT
25V 16V
)
CY82 CY83
CEXF1C101A CEXF1C101A
ELECT ELECT
16V 16V
)
CCY69 CCY70
HCTAJ108MB HCTAH109MB
TANT TANT
35V 25V
Q)
CY85 CY86
CEXF1C220A CEXF1C470A
ELECT ELECT
16V 16V
)
CCY71 CCY74
HCTAH109MB HCTBF100MB
TANT TANT
25V 16V
)
CY87 CY88
CBZF1H104Z CEXF1C220A
CERAMIC ELECT
50V 16V
Q)
CCY75 CCY76
HCTBF100MB HCTBF100MB
TANT TANT
16V 16V
) )
CY90 CY95
CEXF1C470A CMXL1J104J
ELECT MYLAR
16V 63V
Q)
CCY77
HCTBF100MB
TANT
16V
)
CY96
CMXM2A103J
MYLAR
100V
Q)
CCY79
HCTAH109MB
TANT
25V
)
CY97
CMXM2A273J
MYLAR
100V
Q)
CCY84 CCY89
HCBK104KCA HCBK103KCA
S.M.CAP S.M.CAP
50V 50V
Q)
CCY91 CCY92
HCBK104KCA HCQK220JCA
S.M.CAP S.M.CAP
50V 50V
Q)
CCY93 CCY98
HCQK509DCA HCBK102KCA
S.M.CAP S.M.CAP
50V 50V
S)
CCY99 CL28
HCBK104KCA CEXD1H229F
S.M.CAP ELECT
50V 50V
Q)
CL30 CN01
CEXD1H229F CCZF1H103Z
ELECT CERAMIC
50V 50V
)
CN03 CN04
CCZF1H103Z CCZF1H103Z
CERAMIC CERAMIC
50V 50V
Q)
CN05 CN06
CCZF1H103Z CCZF1H103Z
CERAMIC CERAMIC
50V 50V
Q)
CN13 CN18
CCZF1H103Z CCZF1H103Z
CERAMIC CERAMIC
50V 50V
Q)
CN19 CN23
CCZF1H103Z CXCH1H180J
CERAMIC CERAMIC
50V 50V
CN24 CN25
CXCH1H180J CXCH1H220J
CERAMIC CERAMIC
50V 50V
S)
CN26 CN27
CXCH1H220J CEXF1C470A
CERAMIC ELECT
50V 16V
S)
CN30 CN31
CEXF1C470A CEXF1C470A
ELECT ELECT
16V 16V
)
CN33
CBZF1H104Z
CERAMIC
50V
Q)
CN34
CEXF1A471V
ELECT
10V
)
CN35 CN36
CEXF1C470A CEXF1C100A
ELECT ELECT
16V 16V
)
CN38 CN46
CEXF1E221V CEXF1C101A
ELECT ELECT
25V 16V
)
CN47 CN51
CEXF1C101A CCZB1H101K
ELECT CERAMIC
16V 50V
CN53 CN54
CCZB1H101K CCZB1H101K
CERAMIC CERAMIC
50V 50V
S)
CN55
CCZB1H101K
CERAMIC
50V
S)
S)
Q)
Q)
Q)
)
)
)
)
)
)
)
Q)
S)
Q)
)
Q)
Q)
Q)
Q) Q) S)
S)
)
Description
TERMINALS AND LINKS HP601 JA01
4859102430 4859104940
EARPHONE SOCKET AV RCA SOCKET
JS01
4859200401
AV TERMINAL
SWITCHES RLY1 RLY2
5SC0202334 5SC0101003
SWITCH SWITCH
SW01 SW02
JDS1105-6X 5S50101090
SWITCH SWITCH
SW03 SW04
5S50101090 5S50101090
SWITCH SWITCH
SW05 SW06
5S50101090 5S50202002
SWITCH SWITCH
SW07 SW08
5S50202002 5S40202013
SWITCH SWITCH
SW09
5S50101090
SWITCH
SW10
5S50101Z90
SWITCH
DIFFERENCES FOR MODEL TX-14GV1 MECHANICAL PARTS
)
)
) ) S)
S)
Parts Number
16
4859606240
A34EAC01X C.R.T.
18 19
4852154000 4852072201
BACK COVER CABINET
20 21
TNP8EY001LL 58G0000084
CRT PCB DEGAUSS COIL
22 23
TNP8EE001LL 485541584-
MAIN PCB MODEL LABEL
24 25
4855611927 TNP8EP001LL
PANASONIC BADGE POWER PCB
26
48A830610
SPEAKER
MISCELLANEOUS COMPONENTS ANTO5
TSA110001-1
LOOP ANTENNA
M801
4858053600
CARTON
44
)
Q)
Q)
Q) Q) S)
Q) Q)
)
)
)
)
) )
Cct Ref
Parts Number
Description
Cct Ref
SCT01
4859303030
CRT SOCKET
R903
RD-AZ102J
CARBON
0.17W
5%
1K
ZZ130
PTPKCPA604
CUSHIONS SET
R904 R905
RD-AZ152J RD-AZ152J
CARBON CARBON
0.17W 0.17W
5% 5%
1.5K 1.5K
R906 RC575
RD-AZ152J HRFT183JCA
CARBON S.M.CARB
0.17W 0.1W
5% 5%
1.5K 18K
RC583
HRFT823JCA
S.M.CARB
0.1W
5%
82K
TRANSFORMERS T801
50M4042A3
TRANSFORMER
58H0000016
COIL
COILS L404
Parts Number
Description
CAPACITORS
RESISTORS
C415
CMYE2D514J
MYLAR
200V
Q)
R301 R419
RN-4Z2001F RS01Z229J
FILM FILM
0.25W 1W
1% 5%
2K 2.2
C416 C907
CMYH3C722J CCXB1H561K
MYLAR CERAMIC
1K6V 50V
S)
R572 R833
RD-AZ752J RD-4Z472J
CARBON CARBON
0.17W 0.25W
5% 5%
7.5K 4.7K
C908
CCXB1H561K
CERAMIC
50V
S)
C909
CCXB1H561K
CERAMIC
50V
S)
R834 R901
RD-4Z101J RD-AZ152J
FILM CARBON
0.25W 0.17W
5% 5%
100 1.5K
C914 C915
CZSL1H330J CZSL1H330J
CERAMIC CERAMIC
50V 50V
S)
R902 R903
RD-AZ152J RD-AZ152J
CARBON CARBON
0.17W 0.17W
5% 5%
1.5K 1.5K
C916
CZSL1H330J
CERAMIC
50V
S)
R904 R905
RD-AZ132J RD-AZ132J
FILM FILM
0.07W 0.07W
5% 5%
1.3K 1.3K
R906 RC575
RD-AZ132J HRFT223JCA
FILM S.M.CARB
0.07W 0.1W
5% 5%
1.3K 22K
RC583
HRFT753JCA
S.M.CARB
0.1W
5%
75K
RCJ46
HRFT000-CA
S.M.CARB
0.1W
5%
0
CAPACITORS C415
CMYE2D394J
MYLAR
200V
Q)
C416 C907
CMYH3C622J CCXB1H471K
MYLAR CERAMIC
1K6V 50V
S)
C908 C909
CCXB1H471K CCXB1H471K
CERAMIC CERAMIC
50V 50V
S)
C914
CZSL1H180J
CERAMIC
50V
S)
C915
CZSL1H180J
CERAMIC
50V
S)
C916
CZSL1H180J
CERAMIC
50V
S)
S)
S)
DIFFERENCES FOR MODEL TX-21GV1 MECHANICAL PARTS 17 18
4859625360 4852154100
A51EAL15X17 C.R.T. BACK COVER
19 20
4852072301 TNP8EY001HH
CABINET CRT PCB
21 22
58G0000074 TNP8EE001HH
DEGAUSS COIL MAIN PCB
23 24
4855415814855611928
MODEL LABEL PANASONIC BADGE
25 26
TNP8EP001HH 48A8306200
POWER PCB SPEAKER
MISCELLANEOUS COMPONENTS . M801
PTPKCPD201 4858053700
CUSHIONS SET OUTER CARTON
SCT02
4859302930
CRT SOCKET
TRANSISTORS T801
50M4042A2J
TRANSISTOR
58H0000020
LINEARITY COIL
5PTPS60MB
FILTER
COILS L404
FILTERS Z206
RESISTORS R301 R419
RN-4Z3001F RS01Z439J
CARBON METAL
0.25W 1W
1% 5%
3K 4.3
R572 R833
RD-AZ512J RD-4Z512J
CARBON CARBON
0.17W 0.25W
5% 5%
5.1K 51K
R834 R901
RD-4Z910J RD-AZ102J
CARBON CARBON
0.25W 0.17W
5% 5%
91 1K
R902
RD-AZ102J
CARBON
0.17W
5%
1K
45
S)
S)
3$576/2&$7,219&5
6. EXPLODED VIEW AND PA RTS LIST 6-1. EXPLODED VIEW OF DECK ASS’Y (TOP VIEW)
6-2. EXPLODED VIEW OF DECK ASS’Y (BOTTOM VIEW)
AC001
37
38
3$576/2&$7,219&5
6-3. EXPLODED VIEW OF F/L ASS’Y
39
REPLACEMENT PARTS LIST Important Safety Notice Components Identified by mark have special characteristics important for safety. * When replacing any of these components, use only manufacturers specified parts. In case of ordering these spare parts, please always add the complete Model-Type number to your order.
Cct Ref
Parts Number
Description
Cct Ref
MISCELLANEOUS COMPONENTS A0100
97SA309700
MAIN BASE AS
A0200 A0300
97S0901400 97S2701800
PLATE RACK F/L PBT
A0400 A0500
97SA310900 97SA311000
S SLANT POLE AS T SLANT POLE AS
A0600
97SA308500
L LOADING AS
A0700
97SA308600
R LOADING AS
A0800 A0900
97SA308400 97S3101800
LOADING RACK AS WASHER POLY
A1000 A1000
97S8100700 97S8101200
MOTOR CAPSTAN MOTOR CAPSTAN
A1200 A1300
97S3004000 97SA311200
SPG AC HEAD AC HEAD AS
A1400 A1500
7391300211 97S2604100
NUT HEX LEVER RELAY
A1600 A1700
97S2701400 97SA310700
GEAR CAM PINCH LEVER AS
A1800 A1900
97S3117300 97SA310400
WASHER POLY L/C BRKT TOT AS
A2100 A2200
97SA311600 97S3108200
IDLER PLATE AS WASHER POLY
A2300 A2350
97S2901600 97S2901600
TABLE REEL TABLE REEL
A2400
97S3903600
POLY SLIDER
A2500
97SA310800
TENSION BAND AS
A2600 A2700
97S3003500 97SA309300
SPG TENSION S SUB BRAKE AS
A2800 A2900
97SA309400 97SA309110
T SUB BRAKE AS MAIN BRAKE AS
A3100 A3100
97S8004500 97S8012900
HEAD FE HEAD FE
A3300 A3400
97SA309000 97S3108200
REEL GEAR TOT AS WASHER POLY
A3500 A3600
97S5500400 97S2603500
BELT REEL LEVER RECORD SAFETY
A3700 AC001
97SB381100 97SA381500
EARTH BRCKET AS HEAD CLEANER AS
AD001 AF001
97PA253671 97SA251400
DRUM PRICE AS F/L AS K-MECHA
B1900 B1910
97SA414100 97PA409200
L/C BRKT AS L/C MOTOR AS
B1920 B1930
97P6538222 97P6271500
L/C MOTOR PCB CONNECTOR
B1940 B1960
5SSFF1DKM10 97S9201500
CAM SWITCH WORM WHEEL
M1000
97PC0074D
DECK TOTAL AS
48
Parts Number
Description
SCHEMATIC DIAGRAMS FOR MODELS ZEICHENERKLÄRUNG FÜR MODELL TX-21GV1C / TX-14GV1C