ATS-909 Modification and Alignment

Jul 9, 2009 - Finer SSB tuning (makes steps smaller, but you lose some ability to tune between 1 kHz increments); 4.7k for 10 Hz steps. Replace ceramic ...
803KB taille 4 téléchargements 348 vues
ATS-909 Modification and Alignment

http://www.ab9il.net/ats-909/ats909.html

ATS-909 Modification and Alignment Making a soundly designed receiver perform to its fullest. The ATS-909 / DX-398 is certainly one of the great portable shortwave receivers ever made. It performs reliably, has many fine features, and is widely available at a reasonable cost. Countless people use it as a source for news, information, and entertainment around the world. The radio performs better than many full-sized tabletop receivers of years past. It well outperforms my old DX-160, and does more than my Heathkit HR-1680. Despite this, there is room for improvement. Audio Amplifier Schematic Search Thousands of Catalogs for Audio Amplifier Schematic

Copley Controls Servo and stepper amplifiers Distributed control software

Audio Power Amplifier Contact Suppliers & Manufacturers, Easy Sourcing on B2B Marketplace!

www.globalspec.com

www.copleycontrols.com

Alibaba.com

Site Navigation: ATS-909 HF Receiver Aeronautical Radio

I will not repeat the numerous improvements to the ATS-909 that may be found on other modification websites, but will limit my comments to a few changes that mean the most in my shortwave listening experience with the receiver. I first obtained this dandy radio in 1995, and have taken a soldering iron to it numerous times. It is not a difficult radio to work on, but one must be careful with its surface-mount components. There are a few cables and delicate connectors that should be handled with care. Considering those factors, I suggest making changes described below.

Aviation Photo Galleries Enhanced Single Sideband Very Low Frequency Radio Software Defined Radio Space Weather Flashdrive Linux Virtual Operating Systems Long Range WiFi Linux WiFi Encryption and Data Security!!

Anti-Chuffing Beep Removal Finer SSB tuning (makes steps smaller, but you lose some ability to tune between 1 kHz increments); 4.7k for 10 Hz steps Replace ceramic filter CF6 with a narrower one for better adjacent channel rejection on FM Restore segments of FM tuning range (diode change enables TV audio in the USA and some assisted listening devices) Short resistor R7 to ground - allows gain reduction to zero AGC mods as described here; IF clipping mod not necessary Audio bandwidth enhancement

Other Topics HOME

Improved AGC response: 1. Popular modification sites on the web have suggested reducing capacitor C57 (on Pin15 of IC1) to a value of 10 uF. I disagree, and have had better results leaving it at 22 uF. 2. Capacitor C11 should be verified to be 4.7 uF. 3. The radio does not exercise enough control over strong signals. Local amateur and utility signals frequently slam the S meter to full scale and distort badly. I have solved the problem by increasing R181 to 470K. This slows the rate at which C11 recharges and also allows a more effective control of IF circuit gain.

1 of 2

09/07/2009 21:31

ATS-909 Modification and Alignment

http://www.ab9il.net/ats-909/ats909.html

RF Transmitters/Receivers Get A Wide Selection of Custom Components. Rent, Lease & Buy.

AGC Schematic:

AGC Parts Layout:

www.business.com

RF Band pass Filters Ceramic,Diplexers,Duplexers,Cavity Crystal,LC,Lowpass,Highpass,SAW www.www.anatechelectronics.com

OpenPlant P&ID Software The first P&ID application based on an open data model. Try it free! www.Bentley.com/free-trial

Norden Microwave Amps Custom and standard microwave Amps, Multipliers, Converters www.NordenGroup.com

Audio Modifications for Better Bass Response: To achieve a low end rolloff around 15Hz, coupling capacitors should be increased as indicated: C67 and C68 (output from product detector) 4.7uF C80 (AM / SSB audio into IC3) C93 and C94 (input to audio amplifier IC6)15uF@10v C106 and C107 (input to the L and R power amplifiers IC4 and IC5)10uF@10v 5. C116 and C117 (output of L and R power amplifiers IC4 and IC5)1000uF@10v 6. C132 and C133 (output of auduo amplifier IC6) 10uF@10v 1. 2. 3. 4.

Product Detector Schematic

Product Detector Layout

For better oscillator frequency alignment without a counter, connect the audio to your computer sound card and follow this ATS-909 alignment procedure and refer to the ATS-909 circuit board images and alignment pectrograms..

Trends Audio TA-10.1 amps

Norden Microwave Amps

Audiophile grade 2 channel amps at budget prices www.obadimports.com

Custom and standard microwave Amps, Multipliers, Converters www.NordenGroup.com

©2005 - 2009 AB9IL, All Rights Reserved

2 of 2

09/07/2009 21:31