Chandelier GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for dry locations only.
1A FIXTURE LOOP
6 UPPER CUP UPPER COVER
4 1
SHADE
5 3
COVER NUT
JEWEL
LAMP
CANDLE TUBE SOCKET
2 7
7 LOWER CUP
LOWER COVER
2
FINIAL
1
Install the upper cover by placing it over the upper cup nipple and securing it in place by tightening the cover nut.
2
Insert the lower cup nipple into the fixture, then place the lower cover over the lower cup nipple and secure them in place by tightening the finial.
3
Install the candle tube by slipping it through the socket.
4
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
5
Install the shade by placing it over the lamp. Repeat steps 3-5 for remaining sockets.
6
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
7
Hang the jewels by hooking them to the fixture as shown on drawing.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A 6
BOUCLE DU LUMINAIRE
COUPE SUPÉRIEURE COUVERCLE SUPÉRIEURE
4 1
ABAT-JOUR
5 3
ECROU DE COUVERCLE BIJOU
AMPOULE
TUBE BOUGIE DOUILLE
2 7
7 COUPE INFÉRIEUR 2
COUVERCLE INFÉRIEUR FLEURON
1
Installez le couvercle supérieur en le plaçant sur le attache de coupe supérieure et fixez-la en place en serrant l'écrou de la couvercle.
2
Insérez le attache de coupe inférieur dans le luminaire, puis placez le couvercle inférieur sur le attache de coupe inférieur et fixez-les en place en serrant le fleuron.
3
Installer le tube bougie en glissant à travers le socket.
4
Vissez l'ampoule dans la douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
5
Installer l'abat-jour en le plaçant sur la ampoule. Répétez les étapes 3 à 5 pour les douilles restants.
6
Reportez-vous aux instructions pour supplément clos électrique et installation de luminaire sur boîte de sortie de maison.
7
Accrocher les bijoux en les accrochant à le luminaire comme indiqué sur le dessin.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A 6
BUCLE DE LA LÁMPARA
COPA SUPERIOR CUBIERTA SUPERIOR
4 1
PANTALLA
5 3
TUERCA DE LA CUBIERTA JOYA
BOMBILLA
TUBO DE VELA ENCHUFE
2 7
7 COPA INFERIOR 2
CUBIERTA INFERIOR FINIAL
1
Instale la tapa superior colocándola sobre el niple de la copa superior y fijelos en lugar apretando la tuerca de la cubierta.
2
Inserte el niple de la copa inferior en la lámpara, luego coloque la cubierta inferior sobre el niple de la copa inferior y fíjelos en su lugar apretando el finial.
3
Instale el tubo de vela lo deslizándose a través del enchufe.
4
Enrosque la bombilla en el enchufe. Consulte la etiqueta en el zócalo de la lámpara para obtener información de Max Wattage.
5
Instale la pantalla colocándola sobre la bombilla. Repita los pasos 3-5 para tomas restantes.
6
Siga las instrucciones de Instalación incluido suplemento para eléctricos e instalación del accesorio en la caja de enchufe de casa.
7
Cuelgue las joyas enganchando los en la lámpara, como se muestra en el dibujo.
Install the fixture arms by screwing them to the swivels, then secure them to the hub using the washers and couplers. Place the shade onto the shade base and ...
instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone. Conductores de alimentacion ...
Hamlet 5 and 9 Light Chandelier. 1.0. F3065-5-F3066-9. Chandelier. F3065/5, F3066/9. 1A. 1. CAUTION RISK OF FIRE. -. This product must be installed in ...
junction boxes. This product is suitable for dry locations only. This product may be dimmed with a standard incandescent dimmer. Feed the cord through the ...
Instalar los seguidores de la vela por su inclusión en la parte superior de los tubos de la vela. . Consulte la etiqueta del casquillo de la lámpara para obtener ...
Install the bottom tier to the top tier by screwing the fixture arms to the swivels and bottom of the top tier. Assemble the top tier by screwing the fixture arms to the ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 1. 2. 3.
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SMALL ORNAMENT. THUMB SCREW. 7. F
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage information. Optional: Use enclosed instructions for Swag Hook installation.
DeWitt 4 Light Foyer Chandelier. 1.0. F3072-4. Chandelier. F3072/4. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed ...
Refer to the label on the lamp socket for Max Wattage information. Install and secure the string of beads by hooking them to the top and bottom of the fixture.
Installez les tubes de bougies en les glissant sur les douilles. Installez les suiveurs de la bougie au sommet des tubes de bougies. Vissez l'ampoules dans les ...
Lismore 9 Light Chandelier. 1.1. F2937-3-6. Chandelier. F2937/3+6. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed ...
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket; repeat for remaining sockets. Screw the ...
Install the top cover to the fixture, install the bottom cover to the top cover, and secure them together by screwing the finial onto the top cover. Follow enclosed ...
P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing ... Refer to the label on the lamp socket for Max Wattage information.
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes . Consulte la etiqueta del casquillo de la lámpara para obtener información Max.
Connect the fixture to a suitable ground in accordance to local electrical codes. ... Neatly place all the wires into the junction box, place the canopy onto the ...
