Aircraft Manufacturers, Distributors, Dealers, Engine Overhaul Facilities, Owners and Operators of Teledyne Continental Motors’ Aircraft Engines.
SUBJECT:
EXHAUST FLANGE TO CYLINDER INSTALLATION PROCEDURES
MODELS AFFECTED:
All
Gentlemen: Successful performance and service of an aircraft engine exhaust system is dependent on secure fastening and sealing of the exhaust flange at the engine cylinder exhaust port. These are recommended procedures to be followed when an exhaust flange is installed on a cylinder: 1)
Before assembling the exhaust system to the cylinders, inspect the cylinders, exhaust flanges and exhaust studs for damage and cleanliness. (See applicable manufacturer's publications.)
2)
Install gaskets and properly position the exhaust system on the cylinders. Insure that the exhaust flanges are all firmly seated to the cylinders. In several steps evenly tighten all exhaust nuts to the specified torque value.
3)
After ground run-up to normal operating temperature for inspection purposes and prior to return to flight service, re-torque all exhaust nuts to the specified torque values.
TELEDYNE INDUSTRIES, INC. 1981
TELEDYNE CONTINENTAL MOTORS
Member of GAMA
Aircraft Products Division
General Aviation Manufacturer’s Association
PO Box 90 Mobile Alabama 36601
30 November, 1981
M81-25
Page 2
Listed below are the exhaust gaskets and nuts recommended for use on TCM engines. Also listed are the specified torque values for the nuts. ENGINE
Repeat this procedure at least four (4) times until the oil pressure gauge indicates a stabilized oil pressure reading during rotation. Continue to rotate the engine ...
Operating Handbook. Switch action ... all Ignition Harness spark plug terminals must be ... spark plug terminals following procedures in CLEANING section of the.
Mar 12, 1976 - present which could damage the oil seal surface during installation. ... the seal over the prop flange is available from Borrough's Tool and Equipment Co., 2429 North ... F. Apply a thin coat of Permatex to O.D. of seal. G. USING ...
General Information: Field reports indicate that there have been instances in which the impulse coupling cam assemblies have cracked upon installation. See.
Maintenance (Spare) Parts Affected: None. Compliance: At every installation of drive member or impulse coupling. General Information: In order to avoid ...
Aug 14, 1987 - inch feeler gage, Slick Master Service Manual F-1100, standard shop tools. WEIGHT ... B. Grasp shell of the impulse coupling assembly and gently pull the assembly .... NOTE: If the cotter pin will not align with pin hole in the specifi
REASON FOR. To emphasize the value of the use of correct materials and practices. BULLETIN: relevant to magneto distributor gears. EQUIPMENT. AFFECTED ...
GENERAL INFORMATION: Magneto ignition systems must be tested in the following manner to ensure magnetos are grounded after engine shutdown in order ...
MODELS. AFFECTED: All. The United States Environmental Protection Agency recently adopted regulations under the. Clean Air Act which require that warning ...
In the interest of safety, TCM is recalling and replacing all capacitors P/N 10-349276 with date codes .... corner of the magneto data plate, near the word. "TYPE".
performing a cylinder differential pressure test on all TCM engines. Reference 14 CFR Part 43.13. ..... combustion chamber and on piston crown with excessive ...
Instructions are also provided for the replacement of ..... Using a die grinder or equivalent tool and a fine grinding stone, removed only enough material from the ...
In the initial position, all pits are filled with four stones, thus ... If the last stone is sown into an enemy pit that contains 2 or 3 stones after sowing, the stones are ...
c). Institutional Membership d). Life Membership e). Honorary Life Membership. It is moved by the Executive Committee, and seconded by the Board of Directors, ...
TCM advises any distributor, FBO or Engine. Overhaul Facility to inspect all camshafts packaged in cardboard boxes where paper or paper by-products were ...
Table 1 provides valve application by engine model, cylinder part number, intake valve part number and exhaust valve part number. CATEGORY 5. SIL 02-6A.
Refer to the spark plug manufacturer's data for spark plug servicing information and required specialized tools. Spark plugs must be removed, cleaned, ...
