ZR Series Commercial Specification Troffers with Emergency Driver Includes: ZR14™, ZR22™ and ZR24™
INSTALLATION INSTRUCTIONS
IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
ZR14™
1. DANGER- Risk of shock- Disconnect power before installation. DANGER - RISQUE DE CHOC - COUPER L’ALIMENTATION AVANT L’INSTALLATION 2. CAUTION – Installation and servicing should be performed by qualified personnel only. De-energize before opening. ATTENTION – L’installation et l’entretien doivent être effectués par du personnel qualifié seulement. Mettre hors tension avant l’ouverture 3. To reduce the risk of electric shock, disconnect both standard ZR22™ and emergency power supplies and converter connector of the emergency driver before servicing. Pour réduire le risque de décharge électrique, vous devez déconnecter à la fois le disjoncteur divisionnaire ou les fusibles et les alimentations d’urgence avant l’entretien. 4. Do not use outdoors. Ne pas utiliser à l’extérieur. 5. Do not let power supply cords touch hot surfaces. ZR24™ Ne laissez pas les cordons d’alimentation toucher les surfaces chaudes. 6. Do not mount near gas or electric heaters. Ne montez PAS près des appareils de chauffage de gaz ou électriques. 7. Use caution when servicing batteries. Battery acid can cause burns to skin and eyes. If acid is spilled on skin or eyes, flush acid with fresh water and contact a physician immediately. Faites preuve de prudence lors de l’entretien des batteries. L’acide de batterie peut provoquer des brûlures de la peau et les yeux. Si l’acide est versé sur la peau ou les yeux, rincer à l’eau acide frais et contacter un médecin immédiatement. 8. Equipment should be mounted in locations and heights where it will not readily be subjected to tampering by unauthorized personnel. L’équipement doit être monté dans des endroits et à des hauteurs où il ne sera pas soumis à des altérations par des personnes non autorisées. 9. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. L’utilisation d’accessoires non recommandés par le fabricant peut causer une situation dangereuse. 10. Suitable for suspended ceilings. 11. Max. mounting height: 10 ft. Hauteur de montage max.: 10. 12. Access above ceiling required. Do not install insulation within 3” (76mm) of any part of the luminaire. Accès requis au-dessus du plafond. Ne pas mettre l’isolant à moins de 3 po (76 mm) de toute partie du luminaire 13. Suitable for suspended ceilings. Convient aux plafonds suspendus. 14. Do not handle energized module with wet hands or when standing on wet or damp surfaces, or in water.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE • The ZR Series of recessed troffers is for non-insulated ceiling applications using T-Bar ceiling grid, drywall grid adaptors, and suspended mount.
• Dimming leads shall connect only to circuitry identified as a Class 2 Circuit in accordance with the national and local Electrical Wiring Codes.
• Designed for use in 120-277V 50-60 Hz or 347V 60Hz protected circuit (fuse box, circuit breaker). Supply wire sized as per NEC or governing code(s), 90C rated.
• ** Not intended for use with 9/16” T-Bar grids unless used with a 9/16” accessory clip like “Armstrong® LFC- Fixture Clip” which can be purchased through distribution. Consult factory for nonstandard grid applications.
• Make sure to cap off all unused leads. 1 of 3
LPN00208X0002A0_E
TO INSTALL:
1
T- BAR CEILING MOUNTING T-Bar Clips
STEP 1: Install the (2) supplied T-Bar clips onto the mounting bracket on the outside of the housing. See Figure 1 and 2.
STEP 2: Bring the ZR troffer into the T-Bar Ceiling panel and attach the clips on the housing onto the T-Bar.
SUSPENDED MOUNTING
Mounting Bracket
STEP 1: Attach customer supplied cables to the (2)cable slots on each corner of the housing. See Figure 3.
2
STEP 2: Attach customer supplied cables to mounting surface using customer supplied hardware. Ensuring that mounting surface can support the luminaire. Armstrong® LFC- Fixture Clip to use for 9/16th applications.
0 - 10V DIMMING OPTION STEP 1: Remove the cover of the junction box and bring in appropriate power supply to the junction box using one of the knock-outs. See Figure 4 and 5.
3
STEP 2: Bring dimming conduit into dimming wire compartment using the knock-out. See Figure 5.
STEP 3:
Wire luminaire per “Electrical Connections” section and push all leads into the junction box. Reattach junction box cover that was removed in Step 1 , make sure no wires are pinched.
Cable Slots
STEP 4: Install test switch assembly into ceiling by drilling a 1" hole into the ceiling.
4
STEP 5: Unscrew the small trim ring and place test switch assembly through the ceiling. See Figure 6.
Junction Box Cover
STEP 6: Secure the test switch assembly by screwing the small trim ring removed in Step 5 back onto the test switch assembly. Tighten the larger trim ring above the ceiling until it is snugged tight against the ceiling. See Figure 6 on page 3.
EMERGENCY DRIVER CHECK
5
NOTE: For short-term testing of the emergency function, the battery must be charged for at least one hour. The emergency driver must be charged for at least 24 hours before conducting a long-term test.
Dimming Wire Compartment
STEP 1: When AC power is applied, the charging indicator light is illuminated, indicating the battery is being charged. When power fails, the emergency driver automatically switches to emergency power, operating the LED array. When AC power is restored,
Knock-outs
2 of 3
LPN00208X0002A0_E
the emergency driver returns to the charging mode.
6 Large Trim Ring
Test Switch
Ceiling
Small Trim Ring
STEP 2: Although no routine maintenance is required to keep the emergency driver functional, it should be checked periodically to ensure that it is working. The following schedule is recommended: • Visually inspect the charging indicator light monthly. It should be illuminated. • Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. When the test switch is depressed, the LED array should operate. • Conduct a 90-minute discharge test once a year. The LED array should operate for at least 90 minutes. If the luminaire fails any of these checks, consult service personnel. REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL EMERGENCY DRIVER AND AC DRIVER MUST BE FED FROM THE SAME BRANCH CIRCUIT.
ELECTRICAL CONNECTIONS LUMINAIRE
STEP 1: Using customer supplied 90°C minimum rated wire connectors, make the following electrical connections:
STEP 2: Locate the two red leads in the junction box and connect them using customer supplied connector.
GROUND
BARE OR GREEN/YELLOW
NEUTRAL
WHITE WHITE
SWITCHED HOT
WHITE/RED
UNSWITCHED HOT
BLACK
DIM (+) VIOLET
DIM (-) GREY
VIOLET
GREY **RED
(DIMMING OPTIONAL)
a. Connect the black luminaire lead to the unswitched voltage supply lead. b. Connect the white/red luminaire lead to the switched supply switched. c. Connect white luminaire lead to the neutral supply lead. d. Connect ground bare or green/yellow wire lead to the supply ground lead. e. If 0/1-10V Dimming is used, connect the violet lead to the supply positive dimming lead. If dimming is not being used ensure to cap off the violet lead. f. If 0/1-10V Dimming is used, connect the gray lead to the supply negative dimming lead. If dimming is not being used ensure to cap off the gray lead.
SUPPLY WIRING
NOTE: The emergency driver must be fed from the same branch as the AC Driver.
**RED
** NOTE: DO NOT mate leads until installation is complete and AC power is supplied
FCC NOTICE CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAN ICES-003 (A)/NMB-003 (A)
© 2016 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change. See http://lighting.cree.com/warranty for warranty and specifications. Cree® is a registered trademark, and the Cree logo, ZR14™, ZR22™ and ZR24™ are trademarks of Cree, Inc. Armstrong® is a registered trademark of AWI Licensing LLC.
3 of 3
www.cree.com/lighting
LPN00208X0002A0_E
ZR Series Commercial Specification Troffers with Emergency Driver and Removable Lens Includes: ZR14™, ZR22™ and ZR24™
IMPORTANT SAFEGUARDS
INSTALLATION INSTRUCTIONS
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
ZR14™
1. DANGER- Risk of shock- Disconnect power before installation. DANGER - RISQUE DE CHOC - COUPER L’ALIMENTATION AVANT L’INSTALLATION 2. CAUTION – Installation and servicing should be performed by qualified personnel only. De-energize before opening. ATTENTION – L’installation et l’entretien doivent être effectués par du personnel qualifié seulement. Mettre hors tension avant l’ouverture 3. To reduce the risk of electric shock, disconnect both standard ZR22™ and emergency power supplies and converter connector of the emergency driver before servicing. Pour réduire le risque de décharge électrique, vous devez déconnecter à la fois le disjoncteur divisionnaire ou les fusibles et les alimentations d’urgence avant l’entretien. 4. Do not use outdoors. Ne pas utiliser à l’extérieur. 5. Do not let power supply cords touch hot surfaces. ZR24™ Ne laissez pas les cordons d’alimentation toucher les surfaces chaudes. 6. Do not mount near gas or electric heaters. Ne montez PAS près des appareils de chauffage de gaz ou électriques. 7. Use caution when servicing batteries. Battery acid can cause burns to skin and eyes. If acid is spilled on skin or eyes, flush acid with fresh water and contact a physician immediately. Faites preuve de prudence lors de l’entretien des batteries. L’acide de batterie peut provoquer des brûlures de la peau et les yeux. Si l’acide est versé sur la peau ou les yeux, rincer à l’eau acide frais et contacter un médecin immédiatement. 8. Equipment should be mounted in locations and heights where it will not readily be subjected to tampering by unauthorized personnel. L’équipement doit être monté dans des endroits et à des hauteurs où il ne sera pas soumis à des altérations par des personnes non autorisées. 9. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. L’utilisation d’accessoires non recommandés par le fabricant peut causer une situation dangereuse. 10. Suitable for suspended ceilings. 11. Max. mounting height: 10 ft. Hauteur de montage max.: 10. 12. Access above ceiling required. Do not install insulation within 3” (76mm) of any part of the luminaire. Accès requis au-dessus du plafond. Ne pas mettre l’isolant à moins de 3 po (76 mm) de toute partie du luminaire 13. Suitable for suspended ceilings. Convient aux plafonds suspendus. 14. Do not handle energized module with wet hands or when standing on wet or damp surfaces, or in water.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE • The ZR Series of recessed troffers is for non-insulated ceiling applications using T-Bar ceiling grid, drywall grid adaptors, and suspended mount.
• Dimming leads shall connect only to circuitry identified as a Class 2 Circuit in accordance with the national and local Electrical Wiring Codes.
• Designed for use in 120-277V 50-60 Hz or 347V 60Hz protected circuit (fuse box, circuit breaker). Supply wire sized as per NEC or governing code(s), 90C rated.
• ** Not intended for use with 9/16” T-Bar grids unless used with a 9/16” accessory clip like “Armstrong® LFC- Fixture Clip” which can be purchased through distribution. Consult factory for nonstandard grid applications.
• Make sure to cap off all unused leads.
1 of 4
• Lens and removable end cap may shift during installation. Press center of lens to engage magnet strip and push the end cap against the end panel to eliminate the gap after installation. LPN00467X0002A0_C
TO INSTALL:
1
T- BAR CEILING MOUNTING T-Bar Clips
STEP 1: Install the (2) supplied T-Bar clips onto the mounting bracket on the outside of the housing. See Figure 1 and 2.
STEP 2: Bring the ZR troffer into the T-Bar Ceiling panel and attach the clips on the housing onto the T-Bar.
SUSPENDED MOUNTING
Mounting Bracket
STEP 1: Attach customer supplied cables to the (2)cable slots on each corner of the housing. See Figure 3.
2
STEP 2: Attach customer supplied cables to mounting surface using customer supplied hardware. Ensuring that mounting surface can support the luminaire. Armstrong® LFC- Fixture Clip to use for 9/16th applications.
0 - 10V DIMMING OPTION STEP 1: Remove the cover of the junction box and bring in appropriate power supply to the junction box using one of the knock-outs. See Figure 4 and 5.
3
STEP 2: Bring dimming conduit into dimming wire compartment using the knock-out. See Figure 5.
STEP 3:
Wire luminaire per “Electrical Connections” section and push all leads into the junction box. Reattach junction box cover that was removed in Step 1 , make sure no wires are pinched.
Cable Slots
STEP 4: Install test switch assembly into ceiling by drilling a 1" hole into the ceiling.
4
STEP 5: Unscrew the small trim ring and place test switch assembly through the ceiling. See Figure 6.
Junction Box Cover
STEP 6: Secure the test switch assembly by screwing the small trim ring removed in Step 5 back onto the test switch assembly. Tighten the larger trim ring above the ceiling until it is snugged tight against the ceiling. See Figure 6 on page 3.
EMERGENCY DRIVER CHECK
5
NOTE: For short-term testing of the emergency function, the battery must be charged for at least one hour. The emergency driver must be charged for at least 24 hours before conducting a long-term test.
Dimming Wire Compartment
STEP 1: When AC power is applied, the charging indicator light is illuminated, indicating the battery is being charged. When power fails, the emergency driver automatically switches to emergency power, operating the LED array. When AC power is restored, the emergency driver returns to the charging mode. Knock-outs
2 of 4
LPN00467X0002A0_C
STEP 2:
6 Ceiling
Large Trim Ring
Test Switch
Small Trim Ring
Although no routine maintenance is required to keep the emergency driver functional, it should be checked periodically to ensure that it is working. The following schedule is recommended: • Visually inspect the charging indicator light monthly. It should be illuminated. • Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. When the test switch is depressed, the LED array should operate. • Conduct a 90-minute discharge test once a year. The LED array should operate for at least 90 minutes. If the luminaire fails any of these checks, consult service personnel. REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL EMERGENCY DRIVER AND AC DRIVER MUST BE FED FROM THE SAME BRANCH CIRCUIT.
7 End Cap
CLEANING LENS STEP 1: Locate the end cap with the arrow marks on it, indicating that the end cap is removable. See Figure 7.
Arrow Marks
STEP 2: Grab the lens section next to the end cap and pull lens and end cap together downward gently until end cap just clears luminaire (about 3" to 4" from original position). See Figure 8.
8
STEP 3:
1
Disengage the other end of the lens from the other end cap. Once lens is removed perform cleaning. See Figure 8.
2
Arrow Marked End Cap
STEP 4: After cleaning is complete insert lens back into fixed end cap. Push the removable end cap upward into the housing and using a gentle rocking motion engage the end cap to retention clip. Check removable end cap for any visible gap between the end cap and end panel. If necessary push end cap against the end panel to eliminate gaps. Check lens for any visible gap between the lens and luminaire. If necessary push lens upward at gap location to seal magnetic foam to luminaire. See Figure 9.
DO NOT Rotate Lens Into This Zone
9 2 1
Fixed End Cap
3 of 4
LPN00467X0002A0_C
ELECTRICAL CONNECTIONS LUMINAIRE
STEP 1: Using customer supplied 90°C minimum rated wire connectors, make the following electrical connections:
STEP 2: Locate the two red leads in the junction box and connect them using customer supplied connector.
GROUND
BARE OR GREEN/YELLOW
NEUTRAL
WHITE WHITE
SWITCHED HOT
WHITE/RED
UNSWITCHED HOT
BLACK
DIM (+) VIOLET
VIOLET
DIM (-) GREY
GREY **RED
(DIMMING OPTIONAL)
a. Connect the black luminaire lead to the unswitched voltage supply lead. b. Connect the white/red luminaire lead to the switched supply switched. c. Connect white luminaire lead to the neutral supply lead. d. Connect ground bare or green/yellow wire lead to the supply ground lead. e. If 0/1-10V Dimming is used, connect the violet lead to the supply positive dimming lead. If dimming is not being used ensure to cap off the violet lead. f. If 0/1-10V Dimming is used, connect the gray lead to the supply negative dimming lead. If dimming is not being used ensure to cap off the gray lead.
SUPPLY WIRING
NOTE: The emergency driver must be fed from the same branch as the AC Driver.
**RED
** NOTE: DO NOT mate leads until installation is complete and AC power is supplied
FCC NOTICE CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAN ICES-003 (A)/NMB-003 (A)
© 2017 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change. See http://lighting.cree.com/warranty for warranty and specifications. Cree® is a registered trademark, and the Cree logo, ZR14™, ZR22™ and ZR24™ are trademarks of Cree, Inc. Armstrong® is a registered trademark of AWI Licensing LLC.
4 of 4
www.cree.com/lighting
LPN00467X0002A0_C
ZR Series with Cree SmartCast® Technology Commercial Specification Troffers with Emergency Driver Includes: ZR14™, ZR22™ and ZR24™
IMPORTANT SAFEGUARDS
INSTALLATION INSTRUCTIONS INSTRUCTIONS D’INSTALLATION
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
ZR14™ 1. DANGER- Risk of shock- Disconnect power before installation. DANGER - RISQUE DE CHOC - COUPER L’ALIMENTATION AVANT L’INSTALLATION 2. CAUTION – Installation and servicing should be performed by qualified personnel only. De-energize before opening. ATTENTION – L’installation et l’entretien doivent être effectués par du personnel qualifié seulement. Mettre hors tension avant l’ouverture 3. To reduce the risk of electric shock, disconnect both standard and emergency power supplies and converter connector of the ZR22™ emergency driver before servicing. Pour réduire le risque de décharge électrique, vous devez déconnecter à la fois le disjoncteur divisionnaire ou les fusibles et les alimentations d’urgence avant l’entretien. 4. Do not use outdoors. Ne pas utiliser à l’extérieur. 5. Do not let power supply cords touch hot surfaces. Ne laissez pas les cordons d’alimentation toucher les surfaces chaudes. ZR24™ 6. Do not mount near gas or electric heaters. Ne montez PAS près des appareils de chauffage de gaz ou électriques. 7. Use caution when servicing batteries. Battery acid can cause burns to skin and eyes. If acid is spilled on skin or eyes, flush acid with fresh water and contact a physician immediately. Faites preuve de prudence lors de l’entretien des batteries. L’acide de batterie peut provoquer des brûlures de la peau et les yeux. Si l’acide est versé sur la peau ou les yeux, rincer à l’eau acide frais et contacter un médecin immédiatement. 8. Equipment should be mounted in locations and heights where it will not readily be subjected to tampering by unauthorized personnel. L’équipement doit être monté dans des endroits et à des hauteurs où il ne sera pas soumis à des altérations par des personnes non autorisées. 9. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. L’utilisation d’accessoires non recommandés par le fabricant peut causer une situation dangereuse. 10. Suitable for damp locations. Convient Aux Emplacements Humides. 11. Max. mounting height: 12 ft. Hauteur de montage max.: 12. 12. Access above ceiling required. Do not install insulation within 3” (76mm) of any part of the luminaire. Accès requis au-dessus du plafond. Ne pas mettre l’isolant à moins de 3 po (76 mm) de toute partie du luminaire 13. Suitable for suspended ceilings. 14. Do not handle energized module with wet hands or when standing on wet or damp surfaces, or in water.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE • The ZR Series of recessed troffers is for non-insulated ceiling applications using T-Bar ceiling grid, drywall grid adaptors, and suspended mount.
• Dimming leads shall connect only to circuitry identified as a Class 2 Circuit in accordance with the national and local Electrical Wiring Codes.
• Designed for use in 120-277V 50-60 Hz or 347V 60Hz protected circuit (fuse box, circuit breaker). Supply wire sized as per NEC or governing code(s), 90C rated.
• ** Not intended for use with 9/16” T-Bar grids unless used with a 9/16” accessory clip like “Armstrong® LFC- Fixture Clip” which can be purchased through distribution. Consult factory for nonstandard grid applications.
• Make sure to cap off all unused leads. 1 of 4
LPN00260X0001A0_E
TO INSTALL:
1
T- BAR CEILING MOUNTING
T-Bar Clips
STEP 1: Install the (2) supplied T-Bar clips onto the mounting bracket on the outside of the housing. See Figure 1 and 2.
STEP 2: Bring the ZR troffer into the T-Bar Ceiling panel and attach the clips on the housing onto the T-Bar.
Mounting Bracket
STEP 3: Attach the RF Module to the luminaire by clicking it into place as Shown in Figure 4.
SUSPENDED MOUNTING
2
STEP 1: Attach customer supplied cables to the (2) cable slots on each corner of the housing. See Figure 3. Armstrong® LFC- Fixture Clip to use for 9/16th applications.
3
STEP 2: Attach customer supplied cables to mounting surface using customer supplied hardware. Ensuring that mounting surface can support the luminaire.
STEP 3: Attach the RF Module to the luminaire by clicking it into place as Shown in Figure 4.
INSTALLING TEST SWITCH
Cable Slots
STEP 1: Install test switch assembly into ceiling by drilling a 1" hole into the ceiling.
STEP 2: Unscrew the small trim ring and place test switch assembly through the ceiling. See Figure 5.
Junction Box Cover
4
STEP 3: Secure the test switch assembly by screwing the small trim ring removed in Step 5 back onto the test switch assembly. Tighten the larger trim ring above the ceiling until it is snugged tight against the ceiling. See Figure 5.
RF Module
Knock-outs
5 Large Trim Ring
Ceiling
Test Switch Small Trim Ring
2 of 4
LPN00260X0001A0_E
6 RF Module
Access Hole, Reset Button Inside
Blue LED Placement
EMERGENCY DRIVER CHECK NOTE: For short-term testing of the emergency function, the battery must be charged for at least one hour. The emergency driver must be charged for at least 24 hours before conducting a long-term test.
STEP 1: When AC power is applied, the charging indicator light is illuminated, indicating the battery is being charged. When power fails, the emergency driver automatically switches to emergency power, operating the LED array. When AC power is restored, the emergency driver returns to the charging mode.
STEP 2: Although no routine maintenance is required to keep the emergency driver functional, it should be checked periodically to ensure that it is working. The following schedule is recommended: • Visually inspect the charging indicator light monthly. It should be illuminated. • Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. When the test switch is depressed, the LED array should operate. • Conduct a 90-minute discharge test once a year. The LED array should operate for at least 90 minutes. If the luminaire fails any of these checks, consult service personnel. REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL EMERGENCY DRIVER AND AC DRIVER MUST BE FED FROM THE SAME BRANCH CIRCUIT
RESET RF MODULE NOTE: The Blue LED is located behind the CREE logo on the RF Module. The CREE logo with illuminate blue when the Blue LED is active.
3 of 4
STEP 1: Actuate RESET button through the access hole. Push and hold until LED on RF module begins blinking rapidly (approximately 6-7 seconds). See Figure 6.
STEP 2: Release for 1 sec.
STEP 3: Press/Hold RESET button for 0.5 sec. Light will turn off for a few seconds then go to full bright and the Blue LED on the RF Module should begin a 2 blink sequence. Figure 6.
TROUBLESHOOTING: Out of the box, if the light does not turn on when power is applied: • Check Wiring with power off • If wired correctly, check to see if Blue LED blinking on the RF Module. • If Blue LED is blinking, then perform a RESET (See RESET RF MODULE section). • If Blue LED is on solid or off, call Cree Customer Service. • If you have done a RESET, and the light is still off, call Cree Customer Service. If light is unresponsive, use Cree Configuration Tool to verify configuration.
FCC NOTICE RF Exposure Notice To comply with the FCC/IC RF exposure compliance requirements, this device and its antenna must not be co-located or operating to conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 5cm between the radiator & your body. No other antenna is authorized for use with this product.
FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAN ICES-003 (A)/NMB-003 (A) The LED in the front of this device operates within Risk Group 1 levels per IEC 62471. INDUSTRY CANADA STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. In addition, this device complies with ICES-001 of the Industry Canada (IC) Regulations. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. LPN00260X0001A0_E
ELECTRICAL CONNECTIONS NOTE: The emergency driver must be fed from the same branch as the AC Driver.
STEP 1: Remove the cover of the junction box and bring in appropriate power supply to the junction box using one of the knock-outs. See Figure 3.
LUMINAIRE
a. Connect the black luminaire lead to the unswitched voltage supply lead. b. Connect the white/red luminaire lead to the switched supply switched. c. Connect white luminaire lead to the neutral supply lead. d. Connect ground bare or green/yellow wire lead to the supply ground lead.
SUPPLY WIRING
STEP 2: Using customer supplied 90°C minimum rated wire connectors, make the following electrical connections:
GROUND
BARE OR GREEN/YELLOW
NEUTRAL
WHITE WHITE
SWITCHED HOT
WHITE/RED
UNSWITCHED HOT
BLACK
STEP 3:
**RED
Locate the two red leads in the junction box and connect them using customer supplied connector.
STEP 4:
**RED
Push all leads into the junction box. Reattach junction box cover that was removed in Step 1 , make sure no wires are pinched. ** NOTE: DO NOT mate leads until installation is complete and AC power is supplied
© 2016 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change. See http://lighting.cree.com/warranty for warranty and specifications. Cree® and SmartCast® are registered trademarks, and the Cree logo, and ZR14™, ZR22™ and ZR24™ are trademarks of Cree, Inc. Armstrong® is a registered trademark of AWI Licensing LLC.
4 of 4
www.lighting.cree.com
LPN00260X0001A0_E
