CIRCUIT DESCRIPTION. The O/D main switch is a momentary type switch. When pressing the O/D main switch, the O/D OFF indicator light lights up and ECM ...
O/D Main Switch & O/D OFF Indicator Light Circuit CIRCUIT DESCRIPTION The O/D main switch is a momentary type switch. When pressing the O/D main switch, the O/D OFF indicator light lights up and ECM prohibits shifting to O/D, and when pressing it again, the O/D OFF indicator light goes off and ECM allows shifting to O/D. Turning the IG switch OFF will reset the O/D OFF indicator light.
WIRING DIAGRAM
Instrument Panel J/B 4 1O
GAUGE
ECM
C14 O/D OFF Indicator Light (Combination Meter)
13 1G
R-B
G-O 2
3
13 G-O IE2
4 E5 ODLP
14 G-O IE2
12
B-Y Ignition Switch
O/D Main Switch G-O
2
1
AM1
IG1
4 W-L
2
E5 ODMS
W-B 13 1P
8 1O 2
Instrument Panel J/B
AM1 1 1 *1
1C
B-G 4
Fuiseble ALT Link Block
2
1O
*2
B
*1: *2:
Ex. Puerto Rico Puerto Rico
W-B
ID Battery
D07918
2002 ECHO (RM884U)
Author:
Date:
366
DI-197 DIAGNOSTICS
-
AUTOMATIC TRANSAXLE
INSPECTION PROCEDURE 1
Check operation of O/D main switch PREPARATION: Turn the ignition switch ON. CHECK: (a) Check O/D OFF indicator light when O/D main switch is pushed in to ON. (b) Check O/D OFF indicator light when O/D main switch is pushed again. OK: (a) O/D OFF indicator light lights up. (b) O/D OFF indicator light goes off. OK
Proceed to next inspection shown on problem symptoms tables (See page DI-163 ).
NG
2
Check and replace the combination meter (See page BE-2 ).
NG
Replace the combination meter.
OK
3
Check O/D main switch. PREPARATION: Disconnect the O/D main switch connector. CHECK: Check continuity between terminals 2 and 4 of O/D main switch connector. OK: O/D main switch condition
Specified condition
Press continuously O/D main switch
Continuity
Release O/D main switch
No continuity
Q08233
NG
Replace and repair O/D main switch.
OK 2002 ECHO (RM884U)
Author:
Date:
367
DI-198 DIAGNOSTICS
4
-
AUTOMATIC TRANSAXLE
Check voltage between terminal ODMS of ECM and body ground. PREPARATION: Turn the ignition switch ON. CHECK: Check voltage between terminal ODMS of ECM and body ground when O/D main switch is ON and OFF. OK:
ON
ODMS
O/D main switch
Specified voltage
Press continuously O/D main switch
Below 1.0 V
Release O/D main switch
10 - 14 V
D08011
OK
Check and replace the ECM (See page IN-29 ).
NG
5
Check voltage between terminal ODLP of ECM and body ground. ON
PREPARATION: (a) Disconnect the connector of ECM. (b) Turn the ignition switch ON. CHECK: Check voltage between terminal ODLP of ECM and body ground. OK: Voltage: 7.5 - 14 V
ODLP
(-)
(+)
D05647
OK
Check and replace the ECM (See page IN-29 ).
NG
Check and replace harness and connector between combination meter and ECM, O/D main switch and ECM, O/D main switch and body ground (See page IN-29 ).
this glider will be the perfect lightweight choice for you, all the way from hill ...... b12. 770 c12. 827 a14 5024 d1 5967 a13. 1135 b13. 1163 c13. 1073 b1. 5669.
Welcome to the Triple Seven Team! We're excited that you have chosen to fly the D-light, and we are certain that this glider will be the perfect lightweight choice ...
With IG1 terminal voltage at 8.5 V - 19 V, and when ABS is in non-operation stop light switch circuit is open for 0.3 sec. or longer. â¢Stop light valve. â¢Stop light ...
dans la prise du coupe-circuit. Enchufar en una toma 120VAC. Colocar el sensor de temperatura en el lugar deseado. Conectar el cable de alimentación del ...
By Terrencc O'Neill(EAA 5572). This air-angle indicator was first offered to EAA members in a July,. 1970 SPORT AVIATION article by. Terrence O'Neill, EAA ...
The connection is done easily by plugging the jack connector into the socket located at the rear of the instrument cluster (Kit3) or near the electronic module ...
l'économie mauricienne au deuxième trimestre de 2016. .... 3 : Solde des opinions des entrepreneurs sur les possibilités d'expansion sur les nouveaux marchés.
Rock the latch on the top of the tankand draw it upwards to disengage it. 6. Slightly lift the left side ... 1x Dremel or 1x sharp cutter knife. 1. Remove the Neutral ...
spectrum usage in each environment. This problem is called. AFP problem ..... and channel assignment in wireless LANsâ, IEEE Conference on Local Computer ...
BUILD-IT-YOURSELF. I LIKE SIMPLE. THE flap indicator on my RV-7A was four pieces of tape on the flap showing how many degrees are dialed in. There was.
Jul 31, 2014 - ball sealed inside a curved glass tube, which also contains a liquid to act as a damping medium. ... Skidding. The corrective action is to press -.
SO-1 Micro Cut compound, the area is worked over with the pad doing the work. One cannot force the action - you have to allow the pad to do the proper cutting ...
Du 31 janvier au 10 février 2019. From January 31 to February 10, 2019 sur tout achat de 75$ et plus* on any purchase of $75 or more*. 25$ de rabais. $25 Off.