wrap or transformer wire. Attach stackable banana plugs ... transformer wire or wire wrap wire.) OK Industries .... mains isolation), the common terminal must be ...
Copyright Agilent Technologies 1996-2005 All Rights Reserved
Contents Receiving Your Shipment -2 Packaging -2 Description -3 Compatibility -3 Control and Connector Identification -3 Specifications -4 Characteristics -4 Operation -8 Maintenance -9 Measurement Performance Verification Test -10
Agilent 1146A AC/DC Oscilloscope Current Probe
Agilent 1146A AC/DC Oscilloscope Current Probe Receiving Your Shipment
Receiving Your Shipment Upon receiving your shipment, check that the contents agree with the packing slip. If anything is missing, contact your nearest Agilent Technologies Sales Office. If the shipment was damaged, contact the carrier, then contact the nearest Agilent Technologies Sales Office.
Packaging The 1146A AC/DC Current Oscilloscope Probe is shipped with a separate battery (not installed) and a User’s Guide. WARNING
• Connect the probe to the oscilloscope or voltage measuring instrument before clamping the probe around a conductor. • Never use the probe on circuits rated higher than 600 Vac RMS CAT II or 300 Vac RMS CAT III or with float voltage greater than 600 V. • Never leave the probe clamped around a conductor while it is not connected to an oscilloscope or voltage measuring instrument. • Carefully center the conductor inside the probe jaws and ascertain that the probe is perpendicular to the conductor before closing the jaws. • Avoid, if possible, the proximity of other conductors which may create noise. • Check the magnetic mating surfaces of the probe jaws; these should be free of dirt, rust, or other foreign matter • Do not use a probe which is cracked, damaged or has defective leads.
This symbol signifies that the 1146A AC/DC Oscilloscope Current Probe is protected by double or reinforced insulation. Only use specified replacement parts when servicing the instrument.
This symbol signifies CAUTION! and requests that the user refer to the user manual before using the instrument.
2
Agilent 1146A AC/DC Oscilloscope Current Probe Description
Description The 1146A AC/DC Current Oscilloscope Probe expands oscilloscope applications in industrial, automotive or power environments, and is ideal for analysis and measurement of distorted current waveforms and harmonics. The probe permits accurate display and measurement of currents from 100 mA to 100A rms, DC to 100 kHz without breaking into the circuit. The probe uses Hall effect technology to measure AC and DC signals. The probe connects directly to an oscilloscope through a 2 meter coaxial cable with an insulated BNC.
Compatibility The 1146A AC/DC Current Oscilloscope Probe is compatible with any analog or digital oscilloscope or other voltage measuring instrument which has the following features: • BNC input connector. • Range capable of displaying 0.2 to 0.5 V per division. • Minimum input impedance of 1 MΩ.
Control and Connector Identification
Current Flow for DC Measurements or Supply to Load for AC Measurements Zero Adjust Knob Power Indication LED Range Selection Switch φ = 0.46” (11.8 mm)
Peak Overload Indication LED Battery Compartment Cover Screw Control and Connector Identification
3
Agilent 1146A AC/DC Oscilloscope Current Probe Specifications
Specifications All probe specifications are warranted based on the following conditions: • • • • • • • • •
Within one year of calibration 23° C ±5° C 20% to 75% relative humitidy Probe zeroed 1 minute warm up Battery at 9 V ±0.1 V External magnetic field
degauss/autobalance routine is complete when the indicator light turns off. .... test you compare the voltage output of the amplifier to a reference input. You will ...
"A special coding ring is required when using the P6019 Current. Probe. ..... Input Connector. The input connector is similar to a standard BNC, but has.
Astigmatism. Midrange. Scale Illum. As desired. 8. Turn the Intensity control clockwise and adjust trig- gering controls to obtain a triggered display. (Adjust hori-.
properly or pass performance tests, notify your Agilent Technologies Sales. Office. .... 7 Insert the probe ground legs of the new cable into the circuit board pin ..... When you return the 1155A probe to Agilent for calibration, a new certificate is
AM 503B & AM 5030 Amplifier Instruction Manual i. Table of Contents ...... some future time when you want to return the AM 5030 to all the present settings. Because this string ...... PR,24,28 AWG,2 METER,DUAL SHIELD,24 POS,. 0.085 CTR ...
Figure 3â3: Applying the Amp-Second Product Rule .... Table 3â3: AM 503B and AM 5030 Front-Panel Error Codes. 3â18 ...... direction of electron current flow.
INSTRUCTION. MANUAL. Tektronix, Inc. P.O. Box 500. Beaverton, Oregon. 97077. Serial Number ...... LEAD CONFIGURATIONS AND CASE STYLES ARE TYPICAL, BUT MAY. VARY DUE TO ...... 214-1840-00. 8010100. 8036697. 1.
INTRODUCTION .... manual. ltems listed in the Supplemental Information column are not verified in this manual; they are ...... ed, the readout display from this plug-in channel is again ...... with a solution of warm water and a neutral-pH liquid ...
... fast can signals be before the scope bandwidth is a problem? 10 Gb/s waveform. 33 ps risetime. 18 ps risetime. Real-time oscilloscope. Sampling oscilloscope ...
Î power cord with the appropriate plug configuration is supplied with each ...... MSD. Abbreviation for "most significant digit", which is the digit with the h ig hest.
hig h-light specific feat ures of t he manual designed to aid you i n understanding the operation of your 7854 Oscilloscope. In addition to being used for t he main ...
solutions for electric vehicles are available to meet the ... The systems are ... variable speed motor controls can be used on battery powered electric vehicles.
This configuration works with either 2s or. 3s as signal and either 2g or 3g as ground. Ground. Blade. Active. Probe. Solderable through-hole ground pin.
10,000:1 division ratio and a voltage limit of 500,000 volts (to dissipate 25 watts). The barrel of the probe is a 62" length of 1.5" OD X 1.25" ID fiberglass tubing.
connecting the SuperTAP MPC860 emulator to a target system. Each method is described in .... Refer to the MPC860 user manual's reset section for details.
AN P~MicIIAMEOD t53'~~ct~ h o /L '~O~ ...... t "aR53'l~tE~r~~ t~ I~~73Fa~C7~~CoRSj'I~~~ L ~ ~o. 1Q. ...... IRC FIXED RESISTORS PHILADELPHIA DIV. 75915.
The default scale is Fahrenheit (°F). Press and hold both ... Probe Temperature Range: -40° to 572° F (-40° to 300°C) ... IP rating: IP54 waterproof & dustproof.
At that time the Gentile world powers will be besieging Jerusalem. Christ will deliver .... They will dash you to the ground, you and the children within your walls. They will not ..... As a result, the whole universe will collapse in a cosmic catacl
s Up to 88% Efficiency s Small ... 5V Output Efficiency ..... Information furnished by Linear Technology Corporation is believed to be accurate and reliable.