holes and to lower the bolt hole that attaches the wing fitting to the fuselage wing ... will allow proper assembly of wing cabane struts. 4I3Q TUBE- gooa-g AS ...
DESIGN CHANGE BULLETINS CHANGE. NOTICE EFFECTIVE AT OKCE
BABV ACE-MOOEL'C" ^——2*" —
using a blue ball point pen or blue ink. The distance between the front fitting mounting hole and the bottom of the spar should read 1% in. The distance between the rear fitting mounting hole and the bottom of the spar should read % in. Eliminate the identification "datum line" referring to the center line running through the fitting mounting
holes. (That is the detail that tripped the draftsman resulting in too much angle of incidence). NO CM «N &C
HOLE DIMENSIONS.
THIS HOLE LOWERED J
PART NO 7 0 4 - 2 4 -
FRONT SPAR WINS ROOT FITTING
Add the following note to the blueprint in a position below the fitting illustrations, "check and adjust butt fitting location vertically on spars to obtain 3 deg. angle of incidence, reference sheet No. 1".
In the event the wings have been completed, new s with all types of aircraft whether homebuilt or manufactured, mistakes sometimes creep into aircraft drawings. In an effort to bring these corrections to the attention of our readers we would certainly appreciate receiving any changes or recommendations by distributors of aircraft drawings.
wider fittings should be made to locate the mounting holes in the correct position relative to the angle of incidence, or the same fittings moved, which ever is most convenient. Too high an angle of incidence results in undesirable flight characteristics and should be avoided.
To make our work here at Headquarters easier we would ask you to supply your material typewritten, double spaced, and drawings in dark lined pencil or ink. Mistakes found in drawings or construction practices should immediately be brought to the attention of the plan distributors.
EAA BULLETIN No. 3
A
EAA Biplane—Changes in drawing 2003-2. Improper tube size called out for wing cabane strut top ends. This will allow proper assembly of wing cabane struts. 4I3Q TUBE-
EAA BULLETIN No. 1
Baby Ace Model "C" — This deals with a change in the front spar wing root fitting. This had been published some time ago but possibly some builders of the Baby Ace "C" are not aware of this change. The wing fitting has been redesigned so as to use the same wing spar bolt holes and to lower the bolt hole that attaches the wing fitting to the fuselage wing cabane struts by one inch. This change raises the leading edge and gives the proper angle of incidence. A lower stalling speed, better takeoff and glide qualities are also gained.
gooa-g AS suowu
EAA BULLETIN No. 2
Stits Playboy Model SA3A — Blueprints (revised) Serial Numbers 502 through 591 inclusive. STE-Er\- A.M. BOLT
A drafting mistake has been found in the above listed blueprints, and this bulletin is being sent to all the recorded owners to correct the blueprints in the field. If you no longer have the blueprints please forward this bulletin to the new owner.
OUTE-P
WltOG Pft(OE-t_
Referring to sheet No. 17, the dimension between
the center line of the % in. bolt hole in the wing butt fittings, and the bottom of the spars should be changed
would ask you to supply your material typewritten, double spaced, and drawings in dark lined pencil or ink. Mistakes found in drawings or construction practices ...
German health insurance, statutory pension scheme, and unemployment insurance.10. Both data sets .... practices that were identified by Betcherman (1997) and OECD (1999) as main characteristics of ...... Employment Outlook. OECD, Paris.
X X SB556. X. X. X. âBâ Lower Right Quarter Shaft bushing, Steel instead of sintered Iron. X. SB553. X .... Revised timing procedures for IO-720. SI-1433. SB626.
Certain models of Magnaflite starter drives malfunctioning. Check SB for ... Supercedure of Magnaflite starters with new E-Drive & X-Drive starters. SIL A-132.
Challenge In Asia 1914 1941, Broken The Divine 3 Mr Forbes, Btech 2nd Year Question Paper,. Buddhist Iconography 3rd Reprint Compact Edition, Business Advisory Board Best Practices Guide,. Business Essentials 9th Edition Study Guide, and many more eb
Time allowed: 0 sec. Height: 1,35 m. Time limit: 128 sec. Time limit: 0 sec. Class No.: 9. CSI ***. Accumulator Competition samedi 19 novembre 2016. Start: 9:10.
statistics API - the timedTests and timedTestTime long statistics have been .... Fix console column header resizing by working around Java bug 4760433. ..... [Support for testing classes using reflection will be provided by a JUnit plugin which ...
Grégory BODO. J-C LAPARRA. Davy THIRINGER. Valery BREANT. José NICOLAS. Table: A. Speed: 350 m/min. Obstacles: 12. BARRAGE: 1-6-14-4BC-15-3-9. National RG: Length: 410 m. Efforts: 15. Length: 300 m. FEI RG / Art. 238.2.2. Time allowed:71 sec. Time al
0 sec. Height: 1,40 m. Time limit: 132 sec. Time limit: 0 sec. Class No.: 5. CSI ***. Competition against the clock vendredi 18 novembre 2016. Start: 10:30. 2. 6C.
300 m. FEI RG / Art. 238.2.2. Time allowed:71 sec. Time allowed: 52 sec. Height: 1,45 m. Time limit: 142 sec. Time limit: 104 sec. Class No.: 8. CSI*** 1st QUALIF.
Grégory BODO. J-C LAPARRA. Davy THIRINGER. Valery BREANT. José NICOLAS. Table: A. Speed: 350 m/min. Obstacles: 13. BARRAGE: 1-2-8-15-6AB-9B-16. National RG: Length: 460 m. Efforts: 16. Length: 290 m. FEI RG / Art. 238.2.2. Time allowed:79 sec. Time a
70 sec. Time limit: 66 sec. Class No.: 7. CSI ***. Competition in two Phases vendredi 18 novembre 2016. Start: 15:15. 2. 8A. 1. 5. 4. 8B. 10. 3. 6A. 11. Start. Finish.
Time allowed: 36 sec. Height: 1,20 m. Time limit: 70 sec. Time limit: 72 sec. Class No.: 6. CSI *. Competition in two Phases vendredi 18 novembre 2016. Start: 12: ...
The Story Mind approach to story is a structural approach. But no one reads a book or goes to a movie to enjoy a good structure. No author writes because he is ...