Misc. Drive Info: NEVER enter more than 16,383 cylinders in the system BIOS. This may potentially cause data loss. GB = 1 billion bytes. Total accessible capacity varies depending on operating environment. For more information on cylinder limitations, BIOS, step-by-step installation procedures, troubleshooting procedures and more go to the Maxtor.com Knowledge Base.
Jumper Settings: (Master) - The vertical jumper over the J50 pins is configuring the drive as a Master. The horizontal jumper over the J48 and J46 pins is in the Storage position. (Master with CLJ) - The vertical jumper over the J50 pins is configuring the drive as a Master. The vertical jumper over the J46 pins is in the Cylinder Limitation position (CLJ). (Slave) - No jumper is required to configure the drive as a Slave. The jumpers over the J48, J46, J44 and J42 positions are both in the storage position. (Slave with CLJ) - The jumper over the J44 and J42 positions is in the storage position. The jumper over the J46 pins is in the Cylinder Limitation position (CLJ). (Cable Select) - The jumper over the J48 position is configuring the drive for Cable Select. The jumper over the J44 and J42 pins is in the storage position. (Cable Select with CLJ) - The jumper over the J48 position is configuring the drive for Cable Select. The jumper over the J46 pins is in the Cylinder Limitation position (CLJ).
Key Features: • Maximum Capacity of 40.9 GB • Supports ATA/5 for up to 100 MB/sec data transfers • 2 MB Cache Buffer • 7,200 RPM Spin Speed • < 9.0 ms average seek time
Cable Requirements: An 80-Wire UDMA Interface Cable is REQUIRED for all UDMA/100 & UDMA/66 hard drives. (Recommended for UDMA/33)
technologie, gesteuert durch einen leistungsfähigen RISC-Microprozessor ...... halves: the top half shows the parameters for charge output 1, the lower half those for ...... conforms with the essential protective requirements as laid down in the ...
It is recommended to carefully read this owner's manual before using the product. This will also help .... 2. ANL Key. Press the ANL key (2) to enable the ANL (Automatic Noise Limiter) function, in order to reduce electric or ..... 1.8 KHz ±0.2 KHz
Installation area for water connections. Zone d'installation des bondes et siphons. Einbau Bereich für Ablaufgarnitur und Siphon. 670mm. 26 3/8". 353mm.
Actual performance may vary with local water conditions. ... ont été effectués dans des conditions normales d'essais. .... d'alimentation d'eau ayant une pression de 200 kPa .... Inlet Temperature/Température d'entrée/Temperatura de entrada.
Sustituyendo una instalación existente, quite el montaje viejo. Si remplaçant une installation existante, enlevez le vieux raccord. Fregadero limpio en toda superficie para su nueva instalación. Nettoyer les surfaces de montage de lavabo pour votr
instalación. Nettoyer les surfaces de montage de lavabo pour votre nouvelle installation. Clean the sink mounting surfaces for your new fitting. •. If replacing an ...
Apply pipe sealant tape to thread of the valve. A. Attach ... dos llaves, una para sujetar el empalme y la otra para enroscar ... mangueras o tubos de alimentación.
Fregadero limpio en toda superficie para su nueva instalación. Nettoyer les surfaces de montage de lavabo pour votre nouvelle installation. ⢠Shut off the water ...
B. Attach water supply tubes to the faucet. To avoid twisting the copper supply tube, use two wrenches, one to hold the fitting stable, the other to tighten the nut to.
de plàstico e instale el grifo por el orificio del centro. Mettre du enduit d'étanchéité au silicone sous le joint de plastique et installer le robinet dans le trou central.
Tapón del desagüe. Dispositif principal de fermeture mobile. Spring clip. Pinza sujetadora. Pince. Flange. Brida. Bride. Lock nut. Contratuerca. Écrou de blocage.
