Exhaust Gas Recirculation (EGR) temperature sensor, checking
Page 1 of 2
24-71
Exhaust Gas Recirculation (EGR) temperature sensor, checking Notes: For a functional check of the EGR temperature sensor Repair Group 01, Read measuring value block, display group 017. Component locations
page 24-1 .
- Disconnect EGR temperature sensor harness connector. - Switch multimeter (Fluke 83 or equivalent) to 20 volt range and connect between both terminals of connector using jumper wires from connector test kit VW 1594. - Switch ignition ON. Specified value: approx. 5.0 volts
Exhaust Gas Recirculation (EGR) temperature sensor, checking
Page 2 of 2
24-72
If the specified value is not obtained: - Find and eliminate open circuit in wiring between EGR temperature sensor connector terminal 1 and ECM terminal A23, and then between connector terminal 2 and engine Ground (GND), using wiring diagram. Note: If it becomes necessary to repair or replace any of the EGR temperature sensor electrical terminals, ONLY replace with gold plated terminals. If the specified value is obtained: - Disconnect multimeter and jumper wires from EGR temperature sensor harness connector. - Switch ignition OFF. - Remove EGR temperature sensor. - Switch multimeter (Fluke 83 or equivalent) to 200 k resistance range and connect to EGR temperature sensor terminals using jumper wires from connector test kit VW 1594. - Immerse temperature sensor in hot water (80 212 F) and measure resistance.
to 100 C) (176
to
Resistance must change If resistance does not change: - Replace EGR temperature sensor.
Use the check-boxes to mark your progress. â Please read the ... IC socket. Watch the position of the notch! â R2 : 18K (1 - 8 - 0 - 2 - 1). â R7 : 1K8 (1 - 8 - 0 - 1 ...
Nov 22, 2002 - The first position of the 3 digit display (Heater) fluctuate at certain operating conditions between 0 and 1. Page 7 of 61. Oxygen sensor control ...
jumper wires from VW 1594 test kit. Specified value: approx.1000. - Replace Crankshaft Position (CKP) sensor. - Connect multimeter between terminal 1 and 3 ...
5-year warranty. Enroll by placing the panel into wireless enrollment mode ... Current Draw. Transmitted Indications. 433.92 MHz. One Panasonic CR123A.
T-Off. Trim. 2-Chan. MUX t. PTC. Res. 2-Chan. MUX. VDD. S1. S0. CLK. Data. RST. OUT. VSS. COMP ... Power is supplied to the control IC through VDD and VSS. VDD is the positive ..... 81â3â3440â3569. 1â800â521â6274 or 480â768â2130.
the temperature difference between the measuring junction and the reference junction This constant of proportionality is known as the Seebeck coefficient and ...
May 30, 1975 - Seems you never have enough of a good thing. Well ... of the things that you can and cannot do when it comes to .... After you have determined.
DS600 ±0.5°C Accurate Analog-Output Temperature Sensor ... Stresses beyond those listed under âAbsolute Maximum Ratingsâ may cause permanent damage ...
electronic subsystem which has signal .... shows the internal structure of the device; its ... in manufacturing integrated circuits [9]. .... _documents/doc4684.pdf.
controller as shown in Figure 1, becomes a full function temperature measurement system .... Simple, small and low-cost, this system not only completes the.
supply voltage (ratiometric). ... Due to its ratiometric nature, the AD22100 offers a cost effec- .... The AD22100 is a ratiometric temperature sensor IC whose.
tion applications in personal computers, electronic test equipment, and office .... Device Number ..... with an integrated circuit temperature sensor like the LM75,.
Before proceeding, drain water and/or coolant ... scratches, or water and exhaust leaks may re- sult. 3. ... Using new gasket, install exhaust manifold to cyl-.
Aerodynamic Chromed Steel. EPIQ. Bright Package. Ambient Lighting. Please see your local Peterbilt dealer to use Peterbilt PROSPECTOR to specify options ...
occur, and can eventually burn through. There are no kits to convert these engines from thru drive to thru transom exhaust. By using block off plates, inboard ...
