dérivation de passage. LOS CONECTORES DE 1/2" 90° se muestran en esta posición sólo para facilitar la instalación por el agujero cortado con troquel.

debidamente. Repita el mismo procedimiento con los cables negros. Paso 5 Conecte el cable de cobre de puesta en tierra de la caja de cableado con el cable.

1 0 The Trac system is to be supplied by a single branch circuit 120V. BOHZ. 20A. ... 12 foot Trac - four places. oneal each end of Trac and four feet from each ...

CABLE DESNUDO DE COBRE EN CAJADE CABLEADO. WHITE. BLANC. BLANCO. View with Junction Box Cover Off. Vue sans couvercle de boîte de jonction.

2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation. MOUNTING THE ...

At this point, connect the electrical wire as shown in Fig. 2, making sure that all ... Place the glass over the socket and secure by turning clockwise. Return the ...

Shut off the power at the circuit breaker box (avertissement! couper le courant au ... the cross bar with the green screw provided. 5. Tuck these wire connections ...

do en la lampara. Variateur : Pour les douiites a baase tension, a transfor- mateurs a semi-conducteurs, ti taut l'e- quipement de gradation approprié. Si ce n'est.

TALL CONE. STYLE PENDANT. CORD. CORD ..... national d'électricité et des codes de construction locaux. • Pour éviter tout risque pour les enfants, surveiller ...

of your new Skuttle Steam Humidifier, refer to the applicable sections of this ...... destiné à une installation dans ou sur un conduit ou un plénum de reprise.

preciate your business and consider you a valued customer. We sincerely hope ...... Notre expérience et notre engagement envers notre clientèle nous a permis ...

Do not operate the luminaire with a missing or damaged lamp containment barrier. Installation Instructions for H2 & LV2 Series Art Glass and Classics Pendants.

BARRIER MUST BE USED. WITH T4 LAMP. LAMP CONTAINMENT BARRIER. MR16 OR MINISTAR. LAMP. SOCKET CUP. T4 LAMP. FIG. 12. MR16 OR MINISTAR. LAMP. CLIPS. CLIPS. Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • 770.486.4800 â€

This fixture must be installed according to the National Electric Code and ... Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 ...

Service. There are no user serviceable parts inside. Contact point of purchase for service. LOW VOLTAGE CAUTIONS. Dimming: Low voltage lampholders with ...

Twist lead ends individually. Step 5. Drop the TERMINAL SADDLE by unscrewing TERMINAL SCREWS. Be careful to not remove the TERMINAL SCREWS from the TERMINAL. SADDLES (Fig. 8). Step 6. Simultaneously feed stripped and twisted wire ends from center, ov

Remove SPOKE RING and SOCKET CUP (see Fig. 2). Step 3. For T4 lamp type, remove LAMP CONTAINMENT BARRIER by pulling out of socket cup CLIPS ...

29 janv. 2010 - Color coded insulating sleeves - fast and easy phase identification. Wide variety of ... WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS. WARNING: IF YOU ... SOUDURE : Employer un f

visto por otros] y tubería de drenaje) para desa- lojar el condensado. 3.Fije el ventilador al soporte de montaje mediante los tornillos de hojalata suministrados.

lama reflector (FIG 6). ÉTAPE2: Enlever la lampe . Step 4 Re-connect Iamp and replace Iamp. CAUTION Do Not operate without Ions in place. ÉTAPE 3 .

Now you have a choice as to how to proceed with the bushing replacement: Method 1- (Preferred), Bushing replacement without key mechanism disassembly.

If the power disconnect is not integral and is out-of-sight, lock it in the open position ... (for summer air circulation), the unit heater fan motor shall be energized.

29 janv. 2010 - Male and female contacts are sized to match cable size and must be ordered for specific cable size. ..... Bindery. Thickness: Trim. Perfect Bind. Die cut. Saddle Stitch. Drill. Fold. The information in this document is the exclusive P

29 janv. 2010 - NOTE: USE NATIONAL ELECTRIC CODE (NEC) AMPACITY CHART FOR CORRECT ... COUPÉ AVANT DE PROCÉDER À L'INSTALLATION.