(a) Install the floor shift assembly with the 4 bolts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf). (b) Install the wire harness clamps to the shift lever plate. (c) Shift the shift ...
INSTALL FLOOR SHIFT ASSEMBLY Install the floor shift assembly with the 4 bolts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf) Install the wire harness clamps to the shift lever plate.
D08471
(c) (d) (e)
Shift the shift lever in N position, push the lever to the R position side and hold it there. While pulling the cable, install the cable with the nut. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf) Connect the 2 connectors.
D07976
2. (a) ACC
(b) (c) Tape
Clamp
D07974
(d) (e) HINT:
(f)
INSTALL KEY INTERLOCK CABLE With the key in ACC, install the cable cap claw to the key interlock. Install the cable to the clamp for No.1 instrument panel box. Insert the cable end rod (ø4) from the slit of the shift lever plate. Insert the slide cap into the through hole and install. Insert the lever pin into the hole in the cable end. At this time, ensure that the shift lever is in N position. After installation, make sure that the lever pin is pulled by the cable and is stopped with a stopper. To check that the spring for automatic adjustment works properly, hold the slide cap and move it back and forth. Lock the adjust lock cap.
(g) HINT: Rotate it counterclockwise by 90° facing to the front of the vehicle. HINT: Install the cable on the shift lever side with the key in ACC. Make sure the slide amount for the spring for automatic adjustment is 8 mm (0.31 in.). 3. INSTALL REAR CONSOLE BOX, INSTRUMENT CLUSTER PANEL AND COLUMN COVER (See page BO-84 )
2002 ECHO (RM884U)
Author:
Date:
949
AX-25 AUTOMATIC TRANSAXLE
4. (a)
(b) (c) (d) (e)
(f)
With the brake pedal depressed, shift while holding the lock release button in. (The ignition switch must be in ON position.) Shift while holding the lock release button in.
(g)
-
FLOOR SHIFT ASSEMBLY
INSPECT KEY INTERLOCK AND SHIFT LOCK OPERATION Check that the starter operates when the shift lever is in only P and N position and does not operate in the other ranges. Operate the shift lever and check that the reading on the indicator conforms to the actual position. Check that the ignition key can be pulled out in P position. Check that the ignition key does not turn to LOCK position in any other range than P position. Check that the shift lever can be shifted from P position to another position when the shift release button is pressed.
When shifting it to each range, make sure that the shifting lever moves smoothly, can be moderately operated and the position indicator displays correctly. Ranges which can be operated without pressing the shift lever knob button R → N → D → 2, L → 2 → D → N Ranges which can be operated only while pressing the shift lever knob button 2 → L, N → R → P Ranges which can be operated only while pressing the shift lever knob button, ignition switch ON and brake pedal depressed P→R When starting the engine, make sure that the vehicle moves forward when shifting from N to D position, and moves rearward when shifting to R position.
When installing the front seat outer belt, take care that the wiring does not interfere with other parts and is not pinched between other parts. 1. INSTALL FRONT ...
INSTALLATION. 1. INSTALL ELECTRIC COOLING FAN TO RADIATOR. Install the cooling fan with the 3 bolts. Torque: 7.5 N·m (80 kgf·cm, 66 in.·lbf). 2. INSTALL ...
INSTALLATION. 1. INSTALL STARTER. (a) Install the 2 bolts and starter. (b) Connect the starter wire, and install the nut. (c) Connect the starter connector. 2.
(b) Install the coil spring to the shock absorber. HINT: Fit the lower end of the coil spring into the gap of the spring low- er seat. (c) Install the upper insulator with ...
(a) Fasten the front seat belts. (b) Drive the car at 10 mph (16 km/h) and slam on the brakes. Check that the belt locks and cannot be extended at this time. HINT:.
NOTICE: Be careful not to damage the serrations. (c) Install the spacer. (d) Coat a new oil seal lip with molybdenum disulfide lithium base grease. (e) Using SST ...
75.000 - 75.013 mm (2.95275 - 2.95326 in.) Maximum diameter: 75.013 mm (2.95326 in.) If the diameter is greater than maximum, replace the cylinder block. 6.
(a) Remove the door inside handle in order A, B as shown in the illustration. (b) Disconnect the door lock cable from the door inside han- dle. 8. REMOVE PULL ...
INSTALL NEW O-RINGS AND TANKS. (a) After checking that there are no foreign objects in the lock plate groove, install the new O-ring without twisting it. HINT:.
Try to rotate the clutch pinion gear counter- clockwise and check that it locks. If necessary, replace the starter clutch. 13. INSPECT MAGNETIC SWITCH.
Conditions (a), (b) and (c) continue 10 sec. or more with engine speed 900 rpm or less: (2 trip detection logic). (a) Throttle valve fully closed. (b) Mass air flow ...
Alarming time. 60 seconds. Alarming output. Continuous 0.4 secs.: (ON). 0.4 secs.: (OFF). HINT: In the arming condition when either of doors is unlocked with.