Installation Instructions 1. Turn off power ahead of this loadcenter ...
instalar el bloque de terminales para subalimentación. 2. Observe la Fig. 1 e instale el bloque de terminales en el ensamble interior. (UbÃquelo en la posición ...
Tension dangereuse. Peut causer des blessures graves ou la mort. Coupez l’alimentation en électricité avant d’ouvir le panneau.
Voltaje peligroso. Puedo ocasionar lesiones graves o la muerte. Desconecte el interruptor principal de suministro eléctrico antes de abrir el panel.
Installation Instructions 1. Turn off power ahead of this loadcenter before installing sub-feed lug block. 2. Refer to Fig. 1 and install lug block onto interior assembly. (Locate at uppermost bus stab location as shown.) First hook load end into U-shaped form of the interior assembly and push line end fully onto bus. CAUTION! Do not scratch, nick, bend, or otherwise damage bus. 3. Assemble #5–20 screw through lug block into backpan. Torque screw to 13 lb-in. 4. When installing conductors into lug block, torque wire pressure screws to value marked on side of lug block. Note: Breaker Hold-Down Screw Kit is supplied with convertible loadcenters. This kit is also available from your authorized distributor. (BRHDK125, BREQS125 or BREQS125CS)
Instructions de montage 1. Eteindre le courant en amont de ce panneau d’utilisation avant installation du bloc à casses d’alimentation secondaire. 2. En se référant à la figure 1, installer le bloc à casses du côté intérieur (sur la position la plus élevée de la barre). Accrocher d’abord le côté charge sur la forme en U de l’ensemble intérieur et enfoncer complètement le côté ligne sur la barre. ATTENTION ! Ne pas rayer, entamer, plier ou autrement endommager la barre. 3. Installer les vis #5–20 à travers le bloc sur le montant. Serrer à 13 lv-po. 4. Lors de l’installation de conducteurs sur le bloc, serrer les vis de maintien des fils à la valeur indiquée sur le côté du bloc. Note: Un kit à vis de maintien de disjoncteur est fourni avec les panneaux d’utilisation convertible. Il est aussi disponible auprès des revendeurs agréés (BRHDK125, BREQS125 ou BREQS125CS).
Instrucciones para la instalación 1. Apague la alimentación al centro de carga antes de instalar el bloque de terminales para subalimentación. 2. Observe la Fig. 1 e instale el bloque de terminales en el ensamble interior. (Ubíquelo en la posición superior de la lengüeta de la barra colectora, como se muestra). Primero, enganche el extremo de carga en la forma tipo U del ensamble interior y empuje el extremo de línea completamente hacia la barra colectora. CUIDADO: No raye, melle, doble ni dañe de ninguna manera la barra colectora. 3. Coloque el tornillo #5–20 a través del bloque de terminales y hacia la bandeja posterior. Apriete el tornillo con una fuerza máxima de 13 lb-plg. 4. Cuando esté instalando conductores en el bloque de terminales, apriete los tornillos que presionan los alambres al valor marcado en el lateral del bloque de terminales. Nota: El juego de tornillo de sujeción del interruptor se suministra con los centros de carga convertibles. Ese juego puede obtenerse también a través de distribuidor autorizado. (BRHDK125, BREQS125 ó BREQS125CS).
up to (3) #10â12 wires. Multiple wires in a single hole must be of the same size and material. Wire torque: Small #14â10 AWG 20 lb-in. Holes: #8 AWG. 25 lb-in.
Place the main power switch in the âOFFâ position. b) Unscrew the fuse(s), or switch âOFFâ the circuit breaker switch(s), that control the power to the fixture or ...
Clear, Brown, Gold or Black without tracer. Clear, Brown, Gold or Black with tracer. Insulated wire (other than green) with copper conductor. Insulated wire (other ...
instalaciones simplex o FM0486 para instalaciones duplex. Las bombas se deben instalar de acuerdo al Código Eléctrico. Nacional y a todas las ordenanzas y ...
IMPORTANT SAFETY INSTRUCTIONS. MESURES DE SECURITE A ... INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONTSTRUCTION ... curtain or similar combustible material. ... "WARNING Risk of Fire and Electric Shock.".
5 nov. 2010 - Route the fixture wire to the low voltage trunk line. 1. Afloje el tornillo de bloqueo de cabeza hexagonal, gire la horquilla en la posición que se ...
2 avr. 2010 - Services) et Ies maintenir en bon etat (voir Ia note plus bas). b. ..... solide ; d. La verification que tous Ies raccordements inutiIises de. Ia cheminee ..... electronique et Ie cavalier fourni avec Ie fiI BLEU doit _tre utilise entre
This manoeuvre requires most patience and practice. 1. Roll to 90° knife edge L or R. Note aircraft nose drops (further if in direction of prop rotation). Use top ...
Insert the large grease tray all the way under the back edge ..... I Si un conduit de raccordement flexible est utilisé, sa longueur ne doit pas dépasser 4 pi (121,9 ...
All safety messages will follow the safety alert symbol and either the word “DANGER” or ..... F. 6" (15.2 cm) min. clearance from both sides of range to side wall.
ventilation system may cause ignition and combustion problems with this gas ...... Power Spare. RD. WH. BK WH. RD. Reignition. Module. Cooktop. Front View.
any pressure testing of the gas supply piping system at test pressures equal to or ..... Use the following chart to find the exact orifice spud placement. Fully insert ...
that system at test pressures in excess of 1/2 psi (3.5 kPa). Line pressure .... continues until the flame is lit or the knob is turned to OFF. NOTE: The first time ...
These words mean: follow instructions. instructions. DANGER. WARNING. BUILT-IN ..... Connect the 2 yellow-green wires (B) together using a UL listed wire ...
by its side or rear flanges. □. The gas and electric supply should be located as shown in the “Gas and Electric Connection Locations” section so that they are ...
1/2" (13 mm) deep-well socket. 7 mm nut driver. Masking tape. IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking ...
•If you cannot reach your gas supplier, call the fire department. ... Flame spreader (on grill models). □ ...... Test the flame by turning the control from LO to HI,.
Operation of Cooktop Burners” section in the “Complete. Installation” section. 6. .... Remove spring retainer from the cap by pushing against the flat side of the ...
any pressure testing of the gas supply piping system at test pressures equal to .... continues until the flame is lit or the knob is turned to OFF. Check Operation of ...
