or a pair of these boards to another device, such as a TT4, the connections are identified for clarity. RJ-45. Atmega 644 pin. LCD module. Pin 8 +5 Volts. N/A.
Micro-Trak LCD to RJ-45 Adaptor Board The Micro-Trak LCD daughter board provides a simple means of connecting the Crystalfonz and other compatible LCD modules to the Micro-Trak TT4, and can also be used to simplify connections to other devices. The adaptor board is sold unassembled, to allow the user to modify the connections for their particular applications Only two components need be soldered to the PC board ( as shown in photo at right) a .1 microfarad capacitor and a 68 Ohm resistor used to set the backlight level . A 16 pin header is included to facilitate the simplest possible installation. This is accomplished by directly soldering the header to both the adaptor board and the LCD module. Locations for standoffs have been placed on three corners of the board, one inline with the LCD mounting hole, to allow more rigid mounting options if desired. The holes will accommodate a 2-56 screw. When mounting the daughter board to the LCD module, be sure that the back of the daughter board does not come into contact with electronic or mechanical portions of the LCD module. Although a simple 16 pin header is included, you may choose to use a 16 pin SIP socket (not included) and mating headers to make the module removable. Notice the orientation of the module in regards to the LCD board. Do not attempt to reverse the module to allow the connector to be placed into another orientation. This will almost certainly ruin the LCD module
The LCD module when assembled in the fashion shown, allows you to directly plug the device into a Micro-Trak TT4. Keep in mind though that there are multiple wiring schemes for cables using RJ-45 connectors, and you must be sure to use a cable with a straight thru connection. This means that as you hold the cable in your hands, looking at the gold connection side, the same color wire will be on each side. (See photo below)
(Module shown with 16 pin SIP sockets and headers)
Note the orientation of the wires within the RJ-45 patch cord. Looking at the same sides of both connectors, the wires go straight thru to the opposing side. Make sure your cable does not have a “twist” in ANY of the wires within.
Printed Circuit Board Design and Pin Assignments To the left is a representation of the printed circuit board looking from the top and having an “Xray” view of the traces. Ordinarily, there will be no reason for the end user to ever have to worry about how pins are assigned and utilized, since the device is “plug-and-play” with the MicroTrak TT4. On the assumption that some people will wish to adapt on or a pair of these boards to another device, such as a TT4, the connections are identified for clarity.
Color LCD Breakout. Breakout Board for Nokia 6100. 1/27/2006. 1 Overview. This breakout board allows quick and easy development for the Nokia 6100 color ...
The TinyTrak4 DK adapter is a small circuit board designed to ease the connection of a display and a. PS/2 Keyboard to the TinyTrak4 kit and surface mount ...
a copy of the TinyTrak3 manual with the assembly section re-written for the TinyTrak3Plus. .... Add the #4-40 screw through the hole on U2 to mount the voltage ... This selection is done via the J7 jumper on the bottom of the TinyTrak3Plus PCB ...
Where noise generating devices such as dimmer switches or inverter electrical appliances are close by. · Locations subject to frequent vibration or impact.
M10 or M12 thread to ¾â NPT adaptor. Split Washer. Flat Washer. IP Rated. Connection accessory. AR-HBAKM10. ¾â NPT to M10 adaptor kit to work with:.
Do not fully tighten the strain relief set screw, but secure with only 2 or 3 rotations so that the pendant wire can still be moved as needed. 2. Remove a 3/8 inch of ...Termes manquants :
Tabla 1 â Requerimientos para instalación en grupo en caja de pared â Las ALETAS NO SE HAN RETIRADO. Tableau 1 â Exigences de groupement dans les ...
Pull the pendant wire through the bottom hole in the pendant adapter, and then secure the strain relief to the pendant wire. (NOTE: Do not fully tighten the strain ...
PS/2 and OS/2 Warp are registered trademarks of International Business ... All rights, including rights created by patent grant or registration of a utility model or ...
Tillförd energi, målbild mot 2005. Jordbruk och skogsbruk. Transport. Industri. Byggd mijlö och service. Energisektor. (förluster+prod. el). Total amount of energy, ...