OKIN Refined Electric Technology Co., Ltd - UserManual.wiki
OKIN Refined Electric Technology Co., Ltd. Page 1 of 3. Operating ... compliance could void the user's authority to operate the equipment. This device complies ...
OKIN Refined Electric Technology Co., Ltd Operating Manual of Remote Control system Interface of the remote control
2. Electrical configuration diagram
Page 1 of 3
Pair&Power Cord DC
Power Cord AC Power Supply (JLDP.10.023.000)
Control Box CB.11.20.01
SYNC.
Remote model (RF2205)
1
R5.504.01.250
Power Cord AC
1
2
JLDP.10.023.000
Power Supply
1
3
R5.217.01.013
Pair&Power Cord DC
1
Synchronization Cable
4 5
CB.11.20.01
6 7
RF2205
Control Box
1
Motor/(Head&Foot)
2
Remote model
1 Head
Motor
Page 2 of 3
Foot
OKIN Refined Electric Technology Co., Ltd 3. Button description A. BACK UP button：Press and hold the button, the Head actuator will go up. Stop when released. B. BACK DN button：Press and hold the button, the Head actuator will go down. Stop when released. C. FOOT UP button：Press and hold the button, the Foot actuator will go up. Stop when released. D. FOOT DN button：Press and hold the button, the Foot actuator will go down. Stop when released. E. FLAT button: Click the button, the Head and Foot actuator will start up simultaneously and keep running until arriving to their low limited switches,. Running can be stopped by clicking any button. The blue LEDs for backlight are on as long as any button is pressed. IF all buttons are released the LEDs will automatically turn off three seconds later. The blue LED for power is always on as long as the power on.
FCC： Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC RSS warning This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device. ISED RSS Warning: This device complies with Innovation,Science and Economic Development Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Page 3 of 3
Oct 3, 2000 - SCOPE. This specification outlines the pertinent electrical requirements of the RF output modulator which converts the FM video and FM audio ...
Oct 11, 2000 - 2-4. Operation and storage temperature 0-50oC. Conditions for guarantee ... Fs1 5.5 MHz. *output channel. 4-3-4 Audio carrier frequency -8 fs.
Aug 15, 2001 - Test Conditions. 3-1. Testing ambient conditions. Defined as temperature of ... Unit setting conditions. (1). Picture --10 step wave signal ...
â¡Features. â M ax Pow er : 3 kW (SSB). â M anually adjustable variable capacitor and variable inductor. â Connectors for both balanced / unbalanced ...
Oct 10, 2000 - Test Conditions. 3-1. Testing ambient conditions defined as temperature of ... Unit setting conditions. (1). Picture --10 step wave signal ...
Buttonn descriptio. AD UP butt ased. D DN butto ased. OT UP butt ased. OT DN butto ased. T button: C p running u ing any bu blue LEDs f sed the LED lue LED fo. KIN Re of Remot mote contro on tonï¼Press onï¼Press onï¼Press onï¼Press. Click the bu
residual voltage; 0.40 V at 400 mA). .Through-current prevention circuit built in .Separate logic power supply and motor power supply .Spark killer diodes built in.
Oct 15, 2001 - 1. 1. SCOPE. This specification outlines the pertinent electrical requirements of the RF output ... Defined as temperature of 25+/-2oC and humidity of 65+/-5% RH. Note: That ... fs. 1. +8 KHz Input signal none the measurement is taken
â¡Specification. âFrequency : 7/18/21/28/50MHzãCHV-5ã, 7/14/21/28/50MHzãCHV-5Xã. â InputPow er : 7 /1 4 /1 8 M H z 1 5 0 W (SSB), 2 1 /2 8 /5 0 N H z 2 2 ...
channels PWM, three quadrature decoders, GPIOs.8 pins are easy installation with removable to be an SMT module (PCB stamp holes linking) in the mean time.
