OxBox WM Instruction Sheet 7-17 1 Color - Sioux Chief
Washing Machine Outlet Box. Slide boxes onto clip in desired layout. Deslice cajas hacia la abrazadera en diseño deseado. Faites glisser les boîtes sur la clip ...
mount securely to stud ABS stands up to job site abuse • Available with Mini-Rester water hammer arrester • High-quality, North American quarter-turn ball valve
• Boxes
MIP/FSWT
Also Available
Ox Box
drain box
ORDER FRAMES SEPARATELY
18" bracket
supply box
dual frame
18" bracket
plain valves
supply box
box clip
box clip drain box
Standard Pack
Rough-in Pack
valves with arresters
Valve Options
Installation Instructions
Patent Pending
Washing Machine Outlet Box
™
S
D D
Plumb the drain line in the typical manner. Wait for glue to cure before testing.
Plumb the supply lines in the typical manner. Open valves before soldering.
DO NOT allow flame to come into contact with the box.
DO NOT glue box. Apply glue to pipe only.
Straddle stud installations allow for the drain and vent pipe to easily be installed in same stud bay.
5
4
D
Gently bend boxes together. This will Secure with nails/screws in the middle allow the boxes to hold onto the stud. of the box clip and the top nailways.
Floating
S
Clip boxes together in desired configuration. Clip slides into tracks.
3
Separate Studs
S
2
Side Stud
S
1
Straddle Stud Installation
Straddle Stud (strongest installation)
Determine Placement of Boxes
D
Determine Configuration of Boxes
MIP/FSWT
Remove the test cap by clamping and twisting off the test nipple.
Remove Test Cap
To separate boxes, slide a thin, hard material (pocket knife) between the box and clip.
To Separate Boxes
Screw boxes to bracket (screw through bracket first).
Between Studs
Male CPVC
PEX Crimp
PEX F2080
SIOUX CHIEF MANUFACTURING COMPANY, INC.
ProPEX®
Kitec PEX
Install the frame after the wall has been finished.
Install Frame
If boxes are separate (see above), cut the frame to create individual frames.
To Cut Frame
Nail to studs using the top nailway and front two nailway tabs.
Separate Stud Bays
½" Nominal Shank Connections Available
Twist off small tip. Connect ⅝" O.D. compression fitting for air or water test.
Test the System
Tabs fold into metal stud for added rigidity.
Metal Stud Support
Slide bar into top channel. Secure bar to studs. Add bar to bottom as desired.
Connect supply line according to industry standards. Open valves before any soldering. Conecte línea de alimentación de acuerdo a los estándares de industria ...
Slide bracket into top track and secure bracket to studs. Deslice soporte hacia riel de arriba y asegure la soporte a los maderas. Faites glisser le support dans la ...
Slide bracket into top track and secure bracket to studs. Deslice soporte hacia riel de arriba y asegure la soporte a los maderas. Faites glisser le support dans la ...
de agua y haga todas las demás conexiones según la norma ASTM. NOTA: Para cambiar la orientación de la válvula, consulte las instrucciones más abajo. 3.
Install the OmegaPlate⢠to a stud or to a bracket securely. Integral top/bottom track works with common flat brackets. To fix plate position, install a screw ...
STEP 2 - Bend both tabs flat against strap to lock in place. PASO 2 - Doble y aplane ambas orejetas contra la cinta para trabarlas en su sitio. ÉTAPE 2 - Plier les deux languettes à plat contre la courroie pour bloquer en place. CAUTION: SHARP EDGES;
STEP 1 - Bend tabs outward and then insert tabs through the holes. PASO 1 - Doble las orejetas hacia afuera y luego insértelas por los orificios. ÉTAPE 1 - Plier ...
Fixer à un côté de la solive. Enrouler deux fois et fixer à un côté de la solive. Méthodes acceptables pour poser la sangle de suspension en polypropylène tissé ...
Transfer tech sheet (and bag) over to new single metal access panel. Place new panel on dishwasher and align holes in panel with holes in clips. 4. Secure single metal access panel to dishwasher using the. 2 screws supplied. 5. Replace all parts and
... en maintenance comporte une gâche en plastique, celle-ci doit être remplacée par une gâche métallique et le joint d'étanchéité doit également être remplacé.
for Strike Plate and Latch Assembly kit. 1. Unplug dishwasher or ... may not be designed to function with the new latch design in an optimal fashion that could ...
causer un décès ou un choc électrique. Replacer pièces et ... S'assurer de déconnecter la source de courant électrique avant ... composant. FIGURE 1. AXE EN ...
Hold Block 'A' up to vertical stud and mark position of block so that pipe is centered to stud's width. Sujete el bloque 'A' contra el montante vertical y marque la posición del bloque de modo que el tubo quede centrado en el ancho del montante. Ten
Hold Block 'A' up to vertical stud and mark position of block so that pipe is centered to stud's width. Sujete el bloque 'A' contra el montante vertical y marque la posición del bloque de modo que el tubo quede centrado en el ancho del montante. Ten
6 oct. 2005 - Description: Switch, Dual Element Markings ... To avoid risk of electrical shock, personal injury or death; disconnect electrical power before ...
6 juin 2018 - The Caleffi 573 series Is certified by ICC-ES to be in compliance with ... ATTENTION: Si Disconnecteur n'est pas installé, mis en service et ...
1 janv. 2012 - APPLICATION: The Taco SmartPlus is designed to increase hot water comfort while con- serving water and energy. By recirculating âcooledâ hot water back to the water heater, the wait for hot water is decreased to seconds. BENEFITS: