PROximiTy SERiES - Middle Atlantic

Page 3. SUPPLIED COMPONENTS. Sliding Mounting Plate. A. Lever Lock™. B. (2x). Rivet. C. (2x). Washer. D. (4x). Binding Head Screw. E. (4x). Square Nut. F.
7MB taille 0 téléchargements 435 vues
Instruction Sheet

Proximity Series Sliding Mounting Plate

THANK YOU Thank you for purchasing the Proximity Series Sliding Mounting Plate. Please read these instructions thoroughly before installing or assembling this product. PRODUCT FEATURES • The Sliding Mounting Plate (PRX-SMP-15X10) provides mounting of AV components and power that can be conveniently hidden behind a wall-mounted display.

I-00831

Rev A

IMPORTANT SAFETY INSTRUCTIONS • Read these instructions.

• Heed all warnings.

• Clean only with dry cloth.

• Keep these instructions.

• Follow all instructions.

• Only use attachments/accessories specified by the manufacturer.

WARNING: A warning alerts you to a situation that could result in serious personal injury or death.

WARNING: Middle Atlantic Products, Inc. electrical systems conform to and should be properly grounded in compliance with requirements of the current National Electrical Code or codes administered by local authorities. All electrical products may present a possible shock or fire hazard if improperly installed or used. Middle Atlantic Products, Inc. electrical products may bear the mark of a Nationally Recognized Testing Laboratory (NRTL) and should be installed in conformance with current local and/or the National Electrical Code. WARNING: Failure to read, understand and follow the following information can result in serious personal injury, damage to the equipment or voiding of the warranty. It is the responsibility of the Installer/User to ensure that this product is loaded according to specifications.

INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ • Lire ces instructions.

• Respectez tous les avertissements.

• Nettoyer uniquement avec un chiffon sec.

• Conservez ces instructions.

• Suivez toutes les instructions.

• N'utilisez que des accessoires spécifiés par le fabricant.

AVERTISSEMENT: Un avertissement vous avertit d'une situation pouvant entraîner des blessures graves ou la mort.

AVERTISSEMENT: Middle Atlantic Products, Inc. électrique systèmes conformes à devraient être mis à la terre dans conformité avec les exigences de la National actuelle ou comme les codes électrique administré par les autorités locales autorités. Tous les produits électriques peuvent présenter un choc ou un incendie danger si elle est mal installé ou utilisé. Middle Atlantic Products, Inc. produits électriques peuvent porter la marque d'un Nationally Recognized Testing Laboratory (NRTL) et doit être installé en conformité avec courant local et/ou le National Electrical Code. AVERTISSEMENT: Refus de lire, comprendre et suivre la renseignements suivants peut traduire par de graves blessures, des dommages à l'équipement ou invalider la garantie. Il est la responsabilité de l'installateur / utilisateur de s'assurer que ce produit est chargé conformément aux spécifications.

WEIGHT RATINGS Model PRX-SMP-15X10

Weight Rating 15 lbs. Maximum Total Rated Load

WARNING: This product is intended for use only with the products and maximum weights indicated. Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury. Total equipment weight must not exceed 15 lbs. (6.80 kg). AVERTISSEMENT: Cette produit est conçu pour être utilisé uniquement avec les produits et les poids maximum indiqué. uniquement avec les produits et les poids maximaux indiqués. En cas d'utilisation avec d'autres produits ou des produits plus lourds que le poids maximal indiqué, le chariot peut devenir instable et causer des blessures. Le poids total de l'équipement ne doit pas dépasser 6.8 kg (15 lbs).

Page 2

SUPPLIED COMPONENTS

Sliding Mounting Plate A

(2x) Rivet C

(4x) Square Nut F

Lever Lock™ B

(2x) Washer D

(4x) Pan Head Screw G

(4x) Binding Head Screw E

(4x) Drywall Anchor H

Page 3

(20x) Washer J

INSTALLING THE SLIDING MOUNTING PLATE TO THE WALL NOTE: Sliding mounting plate (A) may be installed directly on the wall in 2 horizontal positions as shown. 1. Using (4x) pan head screws (G) and (4x) drywall anchors (H) provided, mount the sliding plate to the wall as shown. (FIGURE A) CAUTION: Only drywall anchors (H) are to be used for mounting to 3/8 minimum to 5/8 maximum thick drywall. ATTENTION: Seules les ancrages de panneaux de cloisons sèches (H) doivent être utilisés pour le montage à 3/8 minimum à 5/8 de cloisons sèches épaisses maximales.

A

Horizontal Wall Mount - Right

Lever Lock Clip

CAUTION: Lever Lock must be mounted with the clip at the bottom. ATTENTION: Le verrou de levier doit être monté avec le clip en bas. A

Lever Lock Clip

Horizontal Wall Mount - Left G

H

FIGURE A

Page 4

INSTALLING THE SLIDING MOUNTING PLATE TO THE FRONT OF AN EXTRUSION 1. Remove screws and endcap to access binding head screws (E) and square nuts (F). 2. Pre-load (4x) binding head screws (E) and (4x) square nuts (F) loose prior to mounting the sliding plate providing clearance for mounting. (FIGURE B)

Screws and Endcap F

E

FIGURE B

3. Mount sliding plate (A) over screws (E) utilizing keyholes in plate by lowering sliding plate until it rests on screws. (FIGURE C) 4. Tighten screws securely against plate. NOTE: At a minimum use 2 pairs of mounting keyholes to safely mount the sliding plate to the extrusion as far apart as possible. A

E

FIGURE C Page 5

INSTALLING THE SLIDING MOUNTING PLATE TO THE FRONT OF AN EXTRUSION CONT’D NOTE: Sliding mounting plate can be place to either the extreme right end of the extrusion, or the extreme left end of the extrusion. (FIGURE D)

Right End

CAUTION: Lever Lock must be mounted with the clip at the bottom. ATTENTION: Le verrou de levier doit être monté avec le clip en bas.

Lever Lock Clip

Left End

FIGURE D Page 6

Lever Lock Clip

INSTALLING THE SLIDING MOUNTING PLATE TO THE BACK OF AN EXTRUSION 1. Remove screws and endcap to access binding head screws (E) and square nuts (F). 2. Pre-load (2x) binding head screws (E), (2x) washers (D) and (2x) square nuts (F) loose prior to mounting the sliding plate providing clearance for mounting. (FIGURE E)

Screws and Endcap E

D

F

FIGURE E 3. Mount sliding plate (A) over screws (E) utilizing keyholes in plate by lowering sliding plate until it rests on screws. (FIGURE F) 4. Tighten screws/washers securely against plate. NOTE: At a minimum use 2 mounting keyholes to safely mount the sliding plate to the extrusion as far apart as possible. A

E

FIGURE F Page 7

INSTALLING THE SLIDING MOUNTING PLATE TO THE BACK OF AN EXTRUSION CONT’D NOTE: Sliding mounting plate can be place to either the extreme right end of the extrusion, or the extreme left end of the extrusion. (FIGURE G)

Right End

CAUTION: Lever Lock must be mounted with the clip at the bottom. ATTENTION: Le verrou de levier doit être monté avec le clip en bas.

Lever Lock Clip

Left End

FIGURE G Page 8

Lever Lock Clip

INSTALLING THE LEVER LOCK PANEL TO THE SLIDING MOUNTING PLATE 1. Attach the Lever Lock plate (B) by installing the side without the clip into the bracket first. 2. Install the side with the clip until it clicks into place. (FIGURE H) Side without clip

Clip

NOTE: Install plastic securing rivet (C) into hole to secure the clip more permanently, if desired.

Side with clip

NOTE: • The Lever Lock plate may be installed on the brackets at different depths. All 4 corners of the Lever Lock plate must be inserted into the brackets at the same depth in order to function correctly. • (20x) Lever Lock plate washers (J) are provided for equipment mounting convenience.

FIGURE H Page 9

CLEARANCE HEIGHTS Method 1 - Attach the sliding mounting plate (A) directly to the wall. (FIGURE J)

3.1” clearance for components between lever lock plate and back of extrusion when mounted to a wall

FIGURE J

Method 2 - Attach the sliding mounting plate (A) to the back of the extrusion. (FIGURE K)

3.1” clearance for components between lever lock plate and wall when mounted to back of the extrusion

FIGURE K

Method 3 - Attach the sliding mounting plate (A) to the front of the extrusion. (FIGURE L)

1.6” clearance for components between lever lock plate and monitor

FIGURE L

Page 10

WARRANTY For warranty information, refer to http://www.middleatlantic.com/company/about-us.aspx#warranty Corporate Headquarters Corporate Voice: 973-839-1011 - Fax: 973-839-1976 / International Voice: +1 973-839-8821 Fax: +1 973-839-4982 www.middleatlantic.com - [email protected] Middle Atlantic Canada Voice: 613-836-2501 - Fax: 613-836-2690 / ca.middleatlantic.com [email protected] Factory Distribution USA: NJ - CA - IL Canada: ON - BC At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.

Page 11