HALLAHAN MC DONOUCH Ma GARCIA OUSFANE BLANCHET REA
1 2 3 4 5 6 7 8
HOWARTH REMUE PAGNEUX ZERIUL MUELLER VAN HAUWAERT RIBEIRO DELFAVERO
1 2 3 4
LYON ZEMAN PROSTIMAH VIELLY
1 2 3 4
MOUSSEUX GARCERA RAMIREZ-RIVAS SANTI
1 2 3 4
A ANCHEZ HAMOUSIN FERO HERRI
MASTER III LLOYD AUGUSTINE MORINO RICCARDO PIERRE GABRIEL GEORG MASTER II LIONEL THOH ANTONIO PETER DENNIS MILOS DIRK LEON ADRIAN JOCHEN MARCO MASTER 1 – 75 KG ANDY JOHN JOSE MOHAMED PATRICK ERIC MASTER 1 + 75 KG STEVE ALAIN FREDERIC FRANCO ANDREAS OLIVIER GREGORY THIERRY JUNIORS JOSEPH DOMINIK TOMAS MORGAN MEN – 65 KG MICHEL JOSE JUAN MORIS MEN – 70 KG MIGUEL FRANTZ RICCARDO ANTHONI
COUNTRY
4 3 5 2 1 6 102
GREAT BRITAIN IRELAND ITALY CATALONIA FRANCE SLOVAKIA GERMANY
14 11 10 100 16 17 12 7 8 15 9
FRANCE SLOVAKIA CATALONIA GREAT BRITAIN ITALY SLOVAKIA BELGIUM FRANCE IRELAND GERMANY ITALY
23 48 22 18 21 20
GREAT BRITAIN SOUTH AFRICA CATALONIA FRANCE FRANCE FRANCE
29 25 24 101 30 27 26 28
GREAT BRITAIN BELGIUM FRANCE ITALY GERMANY FRANCE SOUTH AFRICA FRANCE
November 18 and 19 – 2011 at Schio in Italy Results by Category NAME FIRST NAME BIBS WOMEN – 52 KG REGA BERNADETTE BACCALANI DEBORAH MEN – 75 KG LOUIS-MARIE RAPHAEL CAKIN SYLVAIN MEN - 80 KG NADDEI ALESSANDRO OAKES MARK WIAME RAPHAEL BARRACHINA FELIX LORENZO CONTER FRANCOS BARONE MEHES ROLAN WOMEN + 52 KG MONCOQ FABIENNE MILLINGTON ANNA BOUCHABA AIMEE VENTER JOAN FRANCESCHINI LAURA MEN - 85 KG KERHARO ADRIEN MEN + 85 KG YRIUS JOHNY KOSORINSKY JURAIJ ROBB WAYNE KOEKEMOER GRANT KAMENI TCHEUFFA JULES VINCENT BODY FORM DE HARO JORDANA TELLO MONTSE SIMONE ROSS NINA COUPLE FABIENN 1 JOHNY
COUNTRY
43 45
FRANCE ITALY
47 49
FRANCE FRANCE
53 59 60 54 55 58 57
ITALT GREAT BRITAIN BELGIUM CATALONIA ITALY ITALY SLOVAKIA
61 63 64 44 62
FRANCE GREAT BRITAIN BELGIUM SOUTH AFRICA ITALY
65
FRANCE
68 67 69 66 70
FRANCE SLOVAKIA GREAT BRITAIN SOUTH AFRICA CAMEROON
performing a cylinder differential pressure test on all TCM engines. Reference 14 CFR Part 43.13. ..... combustion chamber and on piston crown with excessive ...
Repeat this procedure at least four (4) times until the oil pressure gauge indicates a stabilized oil pressure reading during rotation. Continue to rotate the engine ...
Operating Handbook. Switch action ... all Ignition Harness spark plug terminals must be ... spark plug terminals following procedures in CLEANING section of the.
Mar 12, 1976 - present which could damage the oil seal surface during installation. ... the seal over the prop flange is available from Borrough's Tool and Equipment Co., 2429 North ... F. Apply a thin coat of Permatex to O.D. of seal. G. USING ...
Instructions are also provided for the replacement of ..... Using a die grinder or equivalent tool and a fine grinding stone, removed only enough material from the ...
In the initial position, all pits are filled with four stones, thus ... If the last stone is sown into an enemy pit that contains 2 or 3 stones after sowing, the stones are ...
c). Institutional Membership d). Life Membership e). Honorary Life Membership. It is moved by the Executive Committee, and seconded by the Board of Directors, ...
TCM advises any distributor, FBO or Engine. Overhaul Facility to inspect all camshafts packaged in cardboard boxes where paper or paper by-products were ...
Table 1 provides valve application by engine model, cylinder part number, intake valve part number and exhaust valve part number. CATEGORY 5. SIL 02-6A.
General Information: Field reports indicate that there have been instances in which the impulse coupling cam assemblies have cracked upon installation. See.
Refer to the spark plug manufacturer's data for spark plug servicing information and required specialized tools. Spark plugs must be removed, cleaned, ...
Maintenance (Spare) Parts Affected: None. Compliance: At every installation of drive member or impulse coupling. General Information: In order to avoid ...
Aug 14, 1987 - inch feeler gage, Slick Master Service Manual F-1100, standard shop tools. WEIGHT ... B. Grasp shell of the impulse coupling assembly and gently pull the assembly .... NOTE: If the cotter pin will not align with pin hole in the specifi
