Outdoor GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for wet locations.
1A
FINIAL GASKET
5
FIXTURE COVER
THREADED NIPPLE
4 FRAME
FIXTURE SCREW
3 LAMP
SHADE
2
1 FIXTURE
SOCKET
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Install the shade by placing it into the fixture and over the socket.
3
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
4
Install the frame to the fixture by securing it in place using the fixture screws.
5
Place the fixture cover and gasket (not included for OL9804) over the threaded nipple and secure it in place by tightening the finial. 1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
FLEURON JOINT
5
COUVERCLE DU LUMINAIRE
ATTACHE FILETÉ
4 CADRE
VIS DU LUMINAIRE
3 AMPOULE
ABAT-JOUR
2
1 LUMINAIRE
DOUILLE
1
Suivez supplément ci-joint des instructions électriques et installation d'accessoires dans la boîte de prise de maison.
2
Installer l'abat-jour en le plaçant dans le luminaire et sur le douille.
3
Vissez l'ampoule dans la douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
4
Installer le cadre sur le luminaire en le fixant en place avec les vis de luminaire.
5
Placez le couvercle et le joint (non inclus pour OL9804) du luminaire sur le attache fileté et fixez-la en place en serrant le fleuron.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
FINIAL JUNTA
5
CUBIERTA DE LA LÁMPARA
CONECTADOR ROSCADO
4 MARCO
TORNILLO DE LA LÁMPARA
3 BOMBILLA
PANTALLA
2
1 LÁMPARA
ENCHUFE
1
Siga las instrucciones de instalación incluido suplemento para eléctricos e instalación del luminario en caja de salida de la casa.
2
Instale la pantalla colocándola en la lámpara y sobre el enchufe.
3
Enrosque la bombilla en el enchufe. Consulte la etiqueta en el enchufe de la lámpara para obtener información de Max Wattage.
4
Instale el marco a la lámpara y fijarlo en su lugar utilizando los tornillos de la lámpara.
5
Coloque la cubierta de la lámpara y la junta (no incluido para OL9804) sobre el conectador roscado y asegúrelo en su lugar apretando el finial.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 2. CAP N
Place the shade and spacer over the socket and secure them in place by screwing the collar nut onto the socket. Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. Install the cover to the fixture arm an
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground in accordance to local ...
Connecter le fil blanc du luminaire (carré et / ou rigide) pour le fil de ligne à neutre ... Parfaitement placer tous les fils dans la boîte électrique, le montage d'essai ...
sujeción en caja de salida de casa. Instale la lámpara enroscándolo en la toma de corriente. Consulte la etiqueta del casquillo de la lámpara para obtener.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamps into the sockets. Refer to the ...
CABLE NEGRO. CAJA ELÉCTRICA. PLACA DE. MONTAJE. LÁMPARA. PRECAUCIÓN: RIESGO DE INCENDIO. Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los
Fije la parte superior del brazo a la cubierta de la lámpara colocando una arandela ... coloque el capuchon decorativo empujándola en el brazo completamente.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house junction box. Raise the housing up to the fixture so that the ...
Install all glass panels by carefully sliding them into the fixture and securing them using the clips. Place the shade and spacer over the socket and secure them in ...
Secure the fixture to the post with the post screws making sure to neatly tuck in all wiring. Insert the shade into the frame and place it over the socket. Screw the lamp into the socket. Refer to the label on the socket for Max Wattage information.
Refer to the label on the socket for Max Wattage information. Follow enclosed supplement installation ... without notification. A Generation Brands Company.
Connect the white driver wire to the neutral power line wire with a wire nut. ... Insert the glass panels into the housing and secure them using the glass panel ...
Install and secure the string of beads by hooking them to the top and bottom of the fixture. Install the candle tube by slipping through the socket. Install candle ...
Connect the white fixture wire to the neutral power line wire with a wire nut. Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws. Install th
Secure the mounting plate to the junction box with two mounting plate screws. Screw the ... Mount the fixture base onto the mounting plate and secure it with the fixture screws. .... Feiss reserves the right to ... A Generation Brands Company.
Augmenter le logement jusqu'Ã le luminaire de sorte que le attache sort par le haut de le luminaire et les fixer ensemble en vissant le fleuron sur le attache.