DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E

RMT-808/809/811/812

SERVICE MANUAL

Ver 1.3 2003. 06

Level 2

US Model Canadian Model Korea Model DCR-TRV6/TRV11/TRV20

AEP Model UK Model Australian Model Chinese Model DCR-TRV6E/TRV11E/TRV20E

E Model Hong Kong Model Tourist Model Photo : DCR-TRV20E RMT-811

DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E

J MECHANISM On the VC-240/241 board This service manual provides the information that is premised the circuit board replacement service and not intended repair inside the VC-240/241 board. Therefore, schematic diagram, printed wiring board and electrical parts list of the VC-240/241 board are not shown. The following pages are not shown. Schematic diagram .......................... Pages 4-17 to 4-66 Printed wiring board ......................... Pages 4-67 to 4-74 Electrical parts list ............................ Pages 6-23 to 6-44

For MECHANISM ADJUSTMENTS, refer to the “DV MECHANICAL ADJUSTMENT MANUAL J MECHANISM ” (9-929-807-11). DCR-TRV6/TRV11/TRV20 : NTSC model DCR-TRV6E/TRV11E/TRV20E : PAL model

• Table showing differences is shown on page 4.

SPECIFICATIONS

— Continued on next page —

DIGITAL VIDEO CAMERA RECORDER

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1.

2. 3.

Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering.

—2—

• Table showing differences is shown on page 4.

• SUPPLIED ACCESSORIES Check that the following accessories are supplied with your camcorder.

1 Wireless Remote Commander (1) RMT-808: DCR-TRV6/TRV6E: AUS, E, JE, CN RMT-809: DCR-TRV6E: AEP, UK RMT-812: DCR-TRV11E: AEP, UK RMT-811: DCR-TRV11/TRV11E: AUS, E, HK, JE, CN/TRV20/ TRV20E

8 Shoulder strap (1)

2 R6 (size AA) battery for Remote Commander (2)

qa Application software: PictureGear 4.1Lite (CD ROM) (1) DCR-TRV11/TRV11E/TRV20/TRV20E only

3 AC-L10A/L10B/L10C AC power adaptor (1), Mains lead (1) 4 NP-FM50 battery pack (1) 5 PC serial cable (1) DCR-TRV11/TRV11E/TRV20/TRV20E only 6 “Memory Stick” (1) DCR-TRV11/TRV11E/TRV20/TRV20E only 7 A/V connecting cable (1)

9 21-pin adaptor (1) DCR-TRV6E: AEP, UK/TRV11E: AEP, UK/TRV20E: AEP, UK 0 Lens cap (1)

qs Lens hood (1) DCR-TRV20/TRV20E only qd 2-pin conversion adaptor (1) DCR-TRV6E: E, HK/TRV6E: E, HK/TRV11: E, HK/ TRV11E: E, HK/TRV20: E, HK/TRV20E: E, HK qf 2-pin conversion adaptor (1) DCR-TRV6: JE/TRV6E: JE/TRV11: JE/TRV11E: JE/ TRV20: JE/TRV20E: JE

• Abbreviation CND : Canadian model CN : Chinese model HK : Hong Kong model KR : Korea model AUS : Australian model JE : Tourist model

—3—

—4—

a 2.5 200k

MEMORY STICK slot DIGITAL I/O (RS232C) LINE IN LCD (size) LCD (pixel)

NTSC PAL

PAL

DCRTRV11E E, AUS, HK, CN, JE

2.5 200k

960H

a 2.5 200k

960H a a a 3.5 184k

a a

a a a 3.5 184k 3.5 184k

960H

960H

960H

a

a

a

• Abbreviation CND : Canadian model CN : Chinese model HK : Hong Kong model

KR : Korea model AUS : Australian model JE : Tourist model

PD-123

PD-124

PD board

a

113k

CK-92

a

113k

CK-94

a

113k

VC-241

113k

113k

113k

CK board

VC board

EVF (pixel) CD-252 board FP-219 flexible

PAL

DCRDCRTRV11 TRV11E US,CND, AEP, UK E, HK, JE, KR NTSC PAL

DCRDCRTRV20 TRV20E US,CND, AEP, UK E,HK,JE, KR PAL

DCRTRV20E E, AUS, HK, CN, JE

a a a 3.5 246k

1152H a a a 3.5 246k

1152H a a a 3.5 246k

1152H

180k a

180k a

PD-124

CK-94

VC-240

180k a

TYPE ST TYPE ST TYPE ST TYPE SH TYPE SH TYPE SH TYPE CA TYPE ST TYPE ST

960H

LCD type

PAL

DCRTRV6E E, AUS, HK, CN, JE

RMT-808 RMT-809 RMT-808 RMT-811 RMT-812 RMT-811 RMT-811 RMT-811 RMT-811 10× 10× 10× 10× 10× 10× 10× 10× 10× 120× 120× 40× 40× 40× 120× 120× 120× 120×

NTSC

CCD imager

Remote commander Lens Digital zoom

Color system

Table for difference of function DCRDCRModel TRV6 TRV6E US,CND, AEP, UK Destination E, HK, JE, KR

a: with 1152H CCD imager. a: with 960H CCD imager. VC-240: with 1152H CCD imager. VC-241: with 960H CCD imager. CK-92: with LCD TYPE CA or TYPE SH. CK-94: with LCD TYPE ST. PD-123: with LCD TYPE CA or TYPE SH. PD-124: with LCD TYPE ST.

TYPE CA, TYPE SH: with PD-123 board. TYPE ST: with PD-124 board.

1152H : with VC-240 board. 960H : with VC-241 board. a: with IC1406 to IC1412 of VC-240 board or with IC1402 to IC1407 of VC-241 board. a: with REC button and IC903 of VC-240/241 board.

NTSC: X101 is 66MHz (DCR-TRV20) X701 is 36MHz (DCR-TRV6/TRV11) PAL: X101 is 54MHz (DCR-TRV20E) X701 is 36MHz (DCR-TRV6E/TRV11E)

Remark

TABLE OF CONTENTS SERVICE NOTE 1. 2.

POWER SUPPLY DURING REPAIRS ····························· 8 TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) ································································ 8

SELF-DIAGNOSIS FUNCTION 1. 2. 3. 3-1. 3-2. 3-3. 4.

SELF-DIAGNOSIS FUNCTION ······································· 9 SELF-DIAGNOSIS DISPLAY ·········································· 9 SERVICE MODE DISPLAY ············································· 9 Display Method ·································································· 9 Switching of Backup No. ··················································· 9 End of Display ···································································· 9 SELF-DIAGNOSIS CODE TABLE ································· 10

1.

GENERAL

Checking supplied accessories ·················································· 1-1 Quick Start Guide ······································································ 1-1 Getting started ··········································································· 1-2 Using this manual ·································································· 1-2 Step 1 Preparing the power supply ········································ 1-2 Installing the battery pack ···················································· 1-2 Charging the battery pack ···················································· 1-3 Connecting to the mains ······················································ 1-4 Step 2 Inserting a cassette ······················································ 1-4 Recording –Basics ····································································· 1-4 Recording a picture ································································ 1-4 Shooting backlit subjects (BACK LIGHT) ·························· 1-7 Shooting in the dark (NightShot/Super NightShot) ············· 1-7 Checking the recording – END SEARCH/ EDIT SEARCH/Rec Review ··············································· 1-8 Playback –Basics ······································································· 1-8 Playing back a tape ································································ 1-8 Viewing the recording on TV ················································ 1-9 Advanced Recording Operations ············································· 1-10 Recording a still image on a tape –Tape Photo recording ··· 1-10 Adjusting the white balance manually ································· 1-11 Using the wide mode ··························································· 1-12 Using the fader function ······················································ 1-12 Using special effects –Picture effect ···································· 1-13 Using special effects –Digital effect ···································· 1-14 Using the PROGRAM AE function ····································· 1-14 Adjusting the exposure manually ········································ 1-15 Focusing manually ······························································· 1-15 Advanced Playback Operations ··············································· 1-16 Playing back a tape with picture effects ······························ 1-16 Playing back a tape with digital effects ······························· 1-16 Enlaring images recorded on tapes –PB ZOOM ················· 1-17 Quickly locating a scene using the zero set memory function ················································································ 1-17 Searching the boundaries of recorded tape by title –Title search ········································································· 1-17 Searching a recording by date –Date search ························ 1-18 Searching for a photo –Photo search/Photo scan ················· 1-18 Editing ····················································································· 1-19 Dubbing a tape ····································································· 1-19 Dubbing only desired scenes –Digital programme editing ···· 1-20 Using with analog video unit and PC – Signal convert function ····················································· 1-23 Recording video or TV programmes ··································· 1-23 Inserting a scene from a VCR –Insert editing ······················ 1-24 Audio dubbing ····································································· 1-25 Superimposing a title ··························································· 1-26 Making your own titles ························································ 1-27 Labeling a cassette ······························································· 1-28 Customizing Your Camcorder ················································· 1-28 Changing the menu settings ················································· 1-28 Resetting the date and time ·················································· 1-30

“Memory Stick” Operations ···················································· 1-30 Using a “Memory Stick” –introduction ······························· 1-30 Recording still images on “Memory Stick”s –Memory photo recording ··················································· 1-32 Superimposing a still picture in a “Memory Stick” on a moving picture –MEMORY MIX ································ 1-34 Recording an image from a mini DV tape as a still image ·· 1-35 Copying still images from a mini DV tape –Photo save ······ 1-36 Viewing a still picture –Memory photo playback ················ 1-36 Copying the image recorded on “Memory Stick”s to mini DV tapes ······································································ 1-37 Enlarging still images recorded on “Memory Stick”s –Memory PB ZOOM ···························································· 1-38 Playing back images in a continuous loop –SLIDE SHOW ··· 1-38 Preventing accidental erasure –Image protection ················ 1-39 Deleting images ··································································· 1-39 Writing a print mark –PRINT MARK ································· 1-40 Additional Information ···························································· 1-40 Usable cassettes ··································································· 1-40 About i.LINK ······································································· 1-41 Troubleshooting ··································································· 1-42 Self-diagnosis display ·························································· 1-43 Warning indicators and messages ········································ 1-43 Using your camcorder abroad ·············································· 1-44 Maintenance information and precautions ··························· 1-44 Quick Reference ······································································ 1-45 Identifying the parts and controls ········································ 1-45

2.

DISASSEMBLY

2-1. LCD SECTION-1 (TRV6/TRV6E MODEL) (PD-124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY) ·················· 2-2 2-2. LCD SECTION-2 (TRV11/TRV11E/TRV20/TRV20E MODEL) (PD-123/124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY) ········ 2-3 2-3. EVF SECTION (LB-64 BOARD) ··································· 2-4 2-4. FRONT PANEL BLOCK ASSEMBLY (MA-385 BOARD), CABINET (R) BLOCK ASSEMBLY ····························· 2-5 2-5. CK-92/94 BOARD, SPEAKER, CONTROL SWITCH BLOCK (CF30150) ····················· 2-6 2-6. DD-137 BOARD, EVF BLOCK ASSEMBLY, BT PANEL SECTION ···················································· 2-7 2-7. LENS SECTION-1 (LENS DEVICE, FP-219 FLEXIBLE BOARD) (TRV6/TRV6E/TRV11/TRV11E MODEL) ···················· 2-8 2-8. LENS SECTION-2 (LENS DEVICE, CD-252 BOARD) (TRV20/TRV20E MODEL) ············································ 2-8 2-9. VC-240/241 BOARD, MECHANISM DECK ················ 2-9 2-10. CONTROL SWITCH BLOCK (FK30150) ··················· 2-10 2-11. JK-188 BOARD, CONTROL SWITCH BLOCK (PS30150) ······································································ 2-10 2-12. MEMORY STICK CONNECTOR (TRV11/TRV11E/TRV20/TRV20E) ····························· 2-11 2-13. HINGE ASSEMBLY, LCD HARNESS PROCESSING · 2-12 2-14. CIRCUIT BOARDS LOCATION ································· 2-13 2-15. FLEXIBLE BOARDS LOCATION ······························ 2-14

3.

BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV6/TRV6E) ······················································ 3-1 3-2. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV11/TRV11E) ·················································· 3-3 3-3. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV20/TRV20E) ·················································· 3-5 3-4. OVERALL BLOCK DIAGRAM (2/3) ··························· 3-7

—5—

3-5. OVERALL BLOCK DIAGRAM (3/3) ··························· 3-9 3-6. POWER BLOCK DIAGRAM (1/2) ······························ 3-11 3-7. POWER BLOCK DIAGRAM (2/2) (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 3-13 3-8. POWER BLOCK DIAGRAM (2/2) (DCR-TRV20/TRV20E) ················································ 3-15

4.

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM-1 ···························· 4-1 FRAME SCHEMATIC DIAGRAM-2 ···························· 4-3 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS ············································ 4-5 • NS-10 (SUPER NIGHTSHOT SW) PRINTED WIRING BOARD ························· 4-6 • CD-252 (CCD IMAGER) PRINTED WIRING BOARD ························· 4-7 • CD-252 (CCD IMAGER) SCHEMATIC DIAGRAM ···························· 4-11 • FP-219 FLEXIBLE BOARD (CCD IMAGER) SCHEMATIC DIAGRAM ···························· 4-13 • FP-219 FLEXIBLE BOARD (CCD IMAGER) PRINTED WIRING BOARD ······················· 4-15 Shematic diagram and printed wiring board of the VC-240/241 board are not shown. Pages from 4-17 to 4-74 are not shown. • CK-92 (KEY) PRINTED WIRING BOARD ······················· 4-75 • FP-181 FLEXIBLE BOARD (PANEL REVERSE) PRINTED WIRING BOARD ······················· 4-78 • CK-94 (KEY) PRINTED WIRING BOARD ······················· 4-79 • CK-92/94 (KEY) SCHEMATIC DIAGRAM ···························· 4-83 • LB-64 (EVF BACK LIGHT) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM ···························· 4-85 • JK-188 (A/V IN/OUT) PRINTED WIRING BOARD ······················· 4-87 • JK-188 (A/V IN/OUT) SCHEMATIC DIAGRAM ···························· 4-89 • CONTROL SWITCH BLOCK (FK-30150) SCHEMATIC DIAGRAM ···························· 4-91 • PD-123 (LCD DRIVE, RGB DRIVE) PRINTED WIRING BOARD ······················· 4-92 • PD-123 (LCD DRIVE)(1/2) SCHEMATIC DIAGRAM ···························· 4-93 • PD-123 (RGB DRIVE)(2/2) SCHEMATIC DIAGRAM ···························· 4-95 • PD-124 (LCD DRIVE)(1/2) SCHEMATIC DIAGRAM ···························· 4-97 • PD-124 (RGB DRIVE)(2/2) SCHEMATIC DIAGRAM ···························· 4-99 • PD-124 (LCD DRIVE, RGB DRIVE) PRINTED WIRING BOARD ····················· 4-101 • SE-107 (MANUAL FOCUS) PRINTED WIRING BOARD ····················· 4-102 • MA-385 (AUDIO I/O) PRINTED WIRING BOARD ····················· 4-103 • MA-385 (AUDIO I/O) SCHEMATIC DIAGRAM ·························· 4-105 • DD-137 (DC/DC CONVERTER)(1/2) SCHEMATIC DIAGRAM ·························· 4-107 • DD-137 (DC/DC CONVERTER)(2/2) SCHEMATIC DIAGRAM ·························· 4-109

• DD-137 (DC/DC CONVERTER)(1/2) PRINTED WIRING BOARD ····················· 4-111 4-3. WAVEFORMS ···························································· 4-113 4-4. MOUNTED LOCATION ············································ 4-125

5 1. 1-1. 5-1. 1-1.

ADJUSTMENTS

Before starting adjustment ··············································· 5-1 Adjusting items when replacing main parts and boards. ··· 5-2 CAMERA SECTION ADJUSTMENT ··························· 5-6 PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) ··················································· 5-6 1-1-1. List of Service Tools ························································ 5-6 1-1-2. Preparations ····································································· 5-7 1-1-3. Precaution ········································································ 5-9 1. Setting the Switch ···························································· 5-9 2. Order of Adjustments ······················································ 5-9 3. Subjects ··········································································· 5-9 1-2. INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE DATA ··· 5-10 1-2-1. INITIALIZATION OF C, D, 8 PAGE DATA ················ 5-10 1. Initializing the C, D, 8 Page Data ·································· 5-10 2. Modification of C, D, 8 Page Data ································ 5-10 3. C Page Table ·································································· 5-10 4. D Page Table ·································································· 5-12 5. 8 Page Table ··································································· 5-13 1-2-2. INITIALIZATION OF B PAGE DATA (DCR-TRV11/TRV11E/TRV20/TRV20E) ···················· 5-14 1. Initializing the B Page Data (DCR-TRV20/TRV20E) ·· 5-14 2. Modification of B Page Data (DCR-TRV20/TRV20E) ·· 5-14 3. Initializing the B Page Data (DCR-TRV11/TRV11E) ·· 5-14 4. Modification of B Page Data (DCR-TRV11/TRV11E) ·· 5-14 5. B Page Table ·································································· 5-15 1-2-3. INITIALIZATION OF E, F, 7 PAGE DATA ················· 5-15 1. Initializing the E, F, 7 Page Data ··································· 5-15 2. Modification of E, F, 7 Page Data ································· 5-15 3. F Page Table ·································································· 5-16 4. E Page Table ·································································· 5-18 5. 7 Page Table ··································································· 5-19 1-3. CAMERA SYSTEM ADJUSTMENTS ························ 5-20 1. 36MHz Origin Oscillation Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E)(VC-241 board) ·· 5-20 2. 54MHz/66MHz Origin Oscillation Adjustment (DCR-TRV20/TRV20E)(CD-252 board) ······················ 5-20 3. Zoom Key Center Adjustment ······································· 5-21 4. HALL Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-21 5. HALL Adjustment (DCR-TRV20/TRV20E) ················· 5-22 6. MR Adjustment (DCR-TRV20/TRV20E) ····················· 5-22 7. Flange Back Adjustment (Using Minipattern Box) ··············································· 5-23 8. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) ·································· 5-24 8-1. Flange Back Adjustment (1) ·········································· 5-24 8-2. Flange Back Adjustment (2) ·········································· 5-24 9. Flange Back Check ························································ 5-25 10. Optical Axis Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-26 11. Picture Frame Setting ···················································· 5-27 12. Color Reproduction Adjustment ···································· 5-28 13. MAX GAIN Adjustment ··············································· 5-29 13-1. MAX GAIN Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-29 13-2. MAX GAIN Data Input (DCR-TRV20/TRV20E) ········· 5-29 14. Auto White Balance & LV Standard Data Input ··········· 5-29 15. Auto White Balance Adjustment ··································· 5-30 16. White Balance Check ···················································· 5-31 17. Mechanical Shutter Adjustment ···································· 5-31

—6—

17-1. Mechanical Shutter Data Input (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-31 17-2. Mechanical Shutter Data Input (DCR-TRV20/TRV20E) ················································ 5-32 18. Angular Velocity Sensor Sensitivity Adjustment ·········· 5-32 1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT ····························································· 5-33 1. VCO Adjustment (VC-240/241 board) ························· 5-33 2. RGB AMP Adjustment (VC-240/241 board) ················ 5-34 3. Contrast Adjustment (VC-240/241 board) ···················· 5-34 4. Backlight Consumption Current Adjustment (VC-240/241 board) ······················································ 5-35 5. White Balance Adjustment (VC-240/241 board) ·········· 5-35 1-5. LCD SYSTEM ADJUSTMENT ··································· 5-36 1-5-1. LCD SYSTEM ADJUSTMENT (DCR-TRV11/TRV11E/TRV20) ··································· 5-36 1. VCO Adjustment (PD-123 board) ································· 5-36 2. RGB AMP Adjustment (PD-123 board) ························ 5-37 3. Contrast Adjustment (PD-123 board) ···························· 5-37 4. V-COM Level Adjustment (PD-123 board) ·················· 5-38 5. V-COM Adjustment (PD-123 board) ···························· 5-38 6. White Balance Adjustment (PD-123 board) ·················· 5-39 1-5-2. LCD SYSTEM ADJUSTMENT (DCR-TRV6/TRV6E/TRV20E) ····································· 5-39 1. VCO Adjustment (PD-124 board) ································· 5-39 2. Bright Adjustment (PD-124 board) ······························· 5-40 3. Black Limit Adjustment (PD-124 board) ······················ 5-40 4. Contrast Adjustment (PD-124 board) ···························· 5-41 5. Center Level Adjustment (PD-124 board) ····················· 5-41 6. V-COM Adjustment (PD-124 board) ···························· 5-42 7. White Balance Adjustment (PD-124 board) ·················· 5-42 5-2. MECHANISM SECTION ADJUSTMENT ·················· 5-43 2-1. HOW TO ENTER RECORD MODE WITHOUT CASSETTE ··································································· 5-43 2-2. HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE ··································································· 5-43 2-3. TAPE PATH ADJUSTMENT ········································ 5-43 1. Preparation for Adjustment ··········································· 5-43 2. Procedure after operations ············································· 5-43 5-3. VIDEO SECTION ADJUSTMENTS ··························· 5-44 3-1. PREPARATIONS BEFORE ADJUSTMENTS ············ 5-44 3-1-1. Equipment Required ······················································ 5-44 3-1-2. Precautions on Adjusting ··············································· 5-45 3-1-3. Adjusting Connectors ···················································· 5-46 3-1-4. Connecting the Equipment ············································ 5-46 3-1-5. Checking the Input Signals (Except AEP/UK model) ··· 5-46 3-1-6. Alignment Tapes ···························································· 5-47 3-1-7. Input/Output Level and Impedance ······························· 5-47 3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT ········ 5-48 1. Initialization of B, C, D, E, F, 7, 8 Page Data ··············· 5-48 2. Serial No. Input ····························································· 5-48 2-1. Company ID Input ························································· 5-48 2-2. Serial No. Input ····························································· 5-48 3. Battery End Check (VC-240/241 board) ······················· 5-50 3-3. SERVO AND RF SYSTEM ADJUSTMENT ··············· 5-51 1. Cap FG Duty Adjustment (VC-240/241 board) ············ 5-51 2. PLL f0 & LPF f0 Adjustment (VC-240/241 board) ······· 5-51 3. Switching Position Adjustment (VC-240/241 board) ··· 5-52 4. AGC Center Level and APC & AEQ Adjustment ········· 5-52 4-1. Preparations before adjustments ···································· 5-52 4-2. AGC Center Level Adjustment (VC-240/241 board) ···· 5-52 4-3. APC & AEQ Adjustment (VC-240/241 board) ············· 5-53 4-4. Processing after Completing Adjustments ···················· 5-53 5. PLL f0 & LPF f0 Final Adjustment (VC-240/241 board) ······················································ 5-53 3-4. VIDEO SYSTEM ADJUSTMENTS ····························· 5-54 3-4-1. Base Band Block Adjustments ······································ 5-54

1. 2.

Chroma BPF f0 Adjustment (VC-240/241 Board) ········ 5-54 S VIDEO OUT Y Level Adjustment (VC-240/241 Board) ······················································ 5-54 3. S VIDEO OUT Chroma Level Adjustment (VC-240/241 Board) ······················································ 5-55 4. AV OUT Y, Chroma Level Check (VC-240/241 Board) ·· 5-55 3-4-2. BIST Check ··································································· 5-56 1. Playback System Check ················································ 5-56 1-1. Preparations for Playback ·············································· 5-56 1-2. IC301 TRX (RF) PB BIST Check ································· 5-56 1-3. IC301 AUD (ABUS) PB BIST Check ··························· 5-56 1-4. IC301 VFD PB BIST Check ········································· 5-56 1-5. IC301 ENCODER BIST Check ···································· 5-57 1-6. Processing after Completing Playback System Check ·· 5-58 2. Recording System Check ·············································· 5-59 2-1. Preparations for recording ············································· 5-59 2-2. IC301 TRX (RF) BIST Check ······································· 5-59 2-3. Processing after Completing Recording System Check ·· 5-59 3-5. IR TRANSMITTER ADJUSTMENTS ························· 5-60 1. IR Video Carrier Frequency Adjustment (VC-240/241 board) ······················································ 5-60 2. IR Video Deviation Adjustment (VC-240/241 board) ··· 5-60 3. IR Audio Deviation Adjustment (VC-240/241 board) ·· 5-61 3-6. AUDIO SYSTEM ADJUSTMENTS ···························· 5-62 1. Playback Level Check ··················································· 5-63 2. Overall Level Characteristics Check ····························· 5-63 3. Overall Distortion Check ··············································· 5-63 4. Overall Noise Level Check ············································ 5-63 5. Overall Separation Check ·············································· 5-63 5-4. SERVICE MODE ·························································· 5-64 4-1. ADJUSTMENT REMOTE COMMANDER ················ 5-64 1. Using the adjustment remote commander ····················· 5-64 2. Precautions upon using the adjustment remote commander ···································································· 5-64 4-2. DATA PROCESS ··························································· 5-65 4-3. SERVICE MODE ·························································· 5-66 1. Setting the Test Mode ···················································· 5-66 2. Emergence Memory Address ········································ 5-66 2-1. EMG Code (Emergency Code) ····································· 5-66 2-2. MSW Code ···································································· 5-67 3. Bit value discrimination ················································ 5-68 4. Switch check (1) ···························································· 5-68 5. Switch check (2) ···························································· 5-69 6. Record of Use check ······················································ 5-69

6.

REPAIR PARTS LIST

6-1-1. FRONT PANEL BLOCK ASSEMBLY AND BATTERY PANEL SECTION ········································ 6-1 6-1-2. CABINET (R) BLOCK ASSEMBLY ····························· 6-2 6-1-3. LCD BLOCK ASSEMBLY (TRV6/TRV6E MODEL) ··· 6-3 6-1-4. LCD BLOCK ASSEMBLY (TRV11/TRV11E/TRV20/TRV20E MODEL) ················ 6-4 6-1-5. CABINET (L) SECTION ················································ 6-5 6-1-6. CABINET (L) SECTION-2 ············································ 6-6 6-1-7. LENS BLOCK ASSEMBLY AND EVF BLOCK ASSEMBLY ············································· 6-7 6-1-8. CASSETTE COMPARTMENT AND DRUM BLOCK ASSEMBLY ········································· 6-8 6-1-9. LS CHASSIS ASSEMBLY ············································· 6-9 6-1-10. MECHANISM CHASSIS BLOCK ASSEMBLY ······ 6-10 6-2. ELECTRICAL PARTS LIST ········································ 6-11 Parts list of the VC-240/241 board are not shown. Pages from 6-23 to 6-44 are not shown. * Optical axis frame and color reproduction frame are shown on page 247 to 249.

—7—

SERVICE NOTE 1.

POWER SUPPLY DURING REPAIRS

In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so that the unit cannot operate. These following two methods are available to prevent this. Take note of which to use during repairs. Method 1. Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side. Method 2. Use the DC IN terminal. (Use the AC power adaptor (AC-L10, AC-VQ800 etc. ))

2. 1 2 3 4 5 6 7 8 9 0 qa

TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) Refer to 2-4. to remove the top cabinet assembly. Refer to 2-4. to remove the front panel block assembly. Refer to 2-4. to remove the cabinet (R) block assembly. Refer to 2-6. to remove the battery panel section. Refer to 2-6. to remove the VC heat sink. (DCR-TRV20/TRV20E model only) Refer to 2-6. to remove DD-137 board. Open the VC-240/241 board. Refer to 2-9. to remove the two screws (M1.7 × 2.5) with which the MD frame assembly is fixed on the CS frame assembly. Refer to 2-9. to remove the mechanism deck and VC-240/241 board. Remove the CN006 (27P 0.3 mm) of the VC-240/241 board. Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.

DC power supply (+4.5Vdc)

: Unloading : Loading Disconnect from CN006 (27P) of VC-240/241 board

CN006

VC

-24

0/2

41

boa

rd

—8—

Loading motor

SELF-DIAGNOSIS FUNCTION 1.

2.

SELF-DIAGNOSIS FUNCTION

Viewfinder or LCD screen

SELF-DIAGNOSIS DISPLAY

When problems occur while the unit is operating, the counter of the viewfinder, LCD screen or LCD window consists of an alphabet and 4-digit numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed code” of the problem.

When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder, LCD screen or LCD window what to do. This function consists of two display; self-diagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.

LCD window

C : 3 1 : 11

C:31:11

Blinks at 3.2Hz

31

C

Detailed Code

Block

Repaired by:

C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer

3.

11

Refer to page 10. Indicates the appropriate Self-diagnosis Code Table. step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.

SERVICE MODE DISPLAY

The service mode display shows up to six self-diagnosis codes shown in the past.

3-1.

Display Method

While pressing the “STOP” key, set the switch from OFF to “VCR or PLAYER”, and continue pressing the “STOP” key for 5 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes. Viewfinder or LCD screen

LCD window

3 C : 3 1 : 11

[3] C : 3 1 : 1 1

Lights up

[3] Backup No.

C:31:11 Self-diagnosis Codes

Control dial

Order of previous errors

3-2.

Switching of Backup No.

By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time

3-3.

End of Display

Turning OFF the power supply will end the service mode display. Note: The “self-diagnosis display” data will be backed up by the coin-type lithium battery of CK-92/94 board BT3201. When this coin-type lithium battery is removed, the “self-diagnosis display” data will be lost by initialization.

—9—

Ver 1.2 2001. 11

4.

SELF-DIAGNOSIS CODE TABLE

Repaired by:

Self-diagnosis Code Block Detailed Function Code

Symptom/State

Correction

C C C C

0 2 2 3

4 1 2 1

0 0 0 1

0 0 0 0

C

3

1

1

1

C C

3 3

1 1

2 2

0 1

C C C C C C

3 3 3 3 3 3

1 1 1 1 1 1

2 2 2 3 4 4

2 3 4 0 0 2

C

3

2

1

0

C

3

2

1

1

C

3

2

2

0

C

3

2

2

1

Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum. FG fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape.

C

3

2

2

2

T reel fault.

C

3

2

2

3

S reel fault.

C

3

2

2

4

T reel fault.

C

3

2

3

0

FG fault when starting capstan.

C

3

2

4

0

FG fault when starting drum

C

3

2

4

2

FG fault during normal drum operations

E

6

1

0

0

Difficult to adjust focus (Cannot initialize focus.)

E

6

1

1

0

Zoom operations fault (Cannot initialize zoom lens.)

E

6

2

0

0

E

6

2

0

1

Steadyshot function does not work well. (With pitch angular velocity sensor output stopped.) Steadyshot function does not work well. (With yaw angular velocity sensor output stopped.)

Use the info LITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Inspect the lens block focus reset sensor (Pin 8,9 of CD-252 board or Pin qk of CN3000 of FP-219 flexible board) when focusing is performed when the control dial is rotated in the focus manual mode, and the focus motor drive circuit (IC201 of VC-240/241 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (Pin ql,w; of CD-252 board or Pin 9 of CN3000 of FP-219 flexible board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC201 of VC-240/241 board) when zooming is not performed. Inspect pitch angular velocity sensor (SE3051 of JK-188 board) peripheral circuits. Inspect yaw angular velocity sensor (SE3052 of JK-188 board) peripheral circuits.

— 10 —

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E SECTION 1 GENERAL

1-1

This section is extracted from instruction manual. (DCR-TRV6E/TRV11E/TRV20E model)

1-2

1-3

1-4

1-5

1-6

1-7

1-8

1-9

1-10

1-11

1-12

1-13

1-14

1-15

1-16

1-17

1-18

1-19

1-20

1-21

1-22

1-23

1-24

1-25

1-26

1-27

1-28

1-29

1-30

1-31

1-32

1-33

1-34

1-35

1-36

1-37

1-38

1-39

1-40

1-41

1-42

1-43

1-44

1-45

1-46

1-47

1-48E

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E SECTION 2 DISASSEMBLY The following flow chart shows the disassembly procedure.

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

2-1. LCD section-1 (TRV6/TRV6E model) (PD-124 board, Inverter transformer unit, Indication LCD block assembly) 2-2. LCD section-2 (TRV11/TRV11E/TRV20/TRV20E model) (PD-123/124 board, Inverter transformer unit, Indication LCD block assembly)

PD-123/124 board service position (All model)

2-3. EVF section (LB-64 board)

LB-64 board service position

2-4. Front panel block assembly (MA-385 board), Cabinet (R) block assembly

MA-385, CK-92/94 boards service position

2-6. DD-137 board, EVF block assembly, BT panel section

MA-385, CK-92/94, DD-137 boards service position

2-7. Lens section-1 (Lens device, FP-219 flexible board) (TRV6/TRV6E/TRV11/TRV11E model) 2-8. Lens section-2 (Lens device, CD-252 board) (TRV20/TRV20E model) 2-12. Memory stick connector (TRV11/TRV11E/TRV20/TRV20E)

2-9. VC-240/241 board, Mechanism deck

2-10. Control switch block (FK30150)

2-11. JK-188 board, Control switch block (PS30150)

[Connection diagram for service position (Mainly for voltage measurement and check)] (MA-385, JK-188, CK-92/94, CD-252, FP-219 flexible, VC-240/241, DD-137 boards, Mechanism deck)

2-5. CK-92/94 board, Speaker, Control switch block (CF30150)

2-13. Hinge assembly, LCD harness processing

2-1

NOTE: Follow the disassembly procedure in the numerical order given.

2-1. LCD SECTION-1 (TRV6/TRV6E MODEL) (PD-124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY) 1 Two screws (M1.7 × 4), lock ace, p2

4 P cabinet (C) assembly

REMOVING THE PD-124 BOARD, INVERTER TRANSFORMER UNIT, INDICAITON LCD BLOCK ASSEMBLY 6 Screw (M1.7 × 2.5)

1 Liquid crystal indicator module (24P)

3 Four claws

5 Two screws (M1.7 × 2.5)

2 Two screws (M1.7 × 4), lock ace, p2

D

2 Back light (Cold cathode fluorescent tube) (15P)

4 Harness (PC-118) (12P) 3 Harness (PC-119) (14P)

qa P B Doa 1 rd 24

8 Inverter transformer unit (5P)

P B Doa 1 r d 24

B

9 PD-124 board A

7 Two tapping screws (M1.7 × 3.5)

5 FP-182 flexible board (21P) qs Release the two claws, and slide the indication LCD block assembly in the direction of the arrow E.

C

qf Indication LCD block assembly

8 P frame (13)

qd LCD holder 9 Back light Cold cathode fluorescent tube

E q;Two claws

0 Liquid crystal indicator module D

qa P frame assembly A

7 Two claws

C

B 6 P cabinet (M)

2-2

2-2. LCD SECTION-2 (TRV11/TRV11E/TRV20/TRV20E MODEL) (PD-123/124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY) 1 Two screws (M1.7 × 4), lock ace, p2

4 P cabinet (C) assembly 3 Four claws

REMOVING THE PD-123/124 BOARD, INVERTER TRANSFORMER UNIT, INDICAITON LCD BLOCK ASSEMBLY

2 Two screws (M1.7 × 4), lock ace, p2

6 Screw (M1.7 × 2.5)

1 Liquid crystal indicator module (24P)

5 Two screws (M1.7 × 2.5)

D

2 Back light (Cold cathode fluorescent tube) (15P)

4 Harness (PC-118) (12P) 3 Harness (PC-119) (14P) 9 PD-123 board (TRV11/TRV11E/ TRV20 model) PD-124 board (TRV20E model)

9 P B Doa rd

8 Inverter transformer unit (5P)

P B Doa rd

B

C

A

5 FP-182 flexible board (21P)

qs Release the two claws, and slide the indication LCD block assembly in the direction of the arrow E.

qf Indication LCD block assembly 8 Back light Cold cathode fluorescent tube

qd LCD holder E

q;Two claws 7 Liquid crystal indicator module D qa P frame assembly C

A 7 Two claws

B 6 P cabinet (M)

[PD-123/124 BOARD SERVICE POSITION (ALL MODEL)] AC IN

DC IN LANC jack

AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)

Adjustment remote commander (RM-95)

CN009 1

2

19

20

Liquid crystal indicator module

P B Doa rd

CPC lid Screw (M1.7 × 4), lock ace, p2

Back light Cold cathode fluorescent tube

CPC-8 jig (J-6082-388-A)

Indication LCD block assembly Inverter transformer unit

PD-123 board (TRV11/TRV11E/TRV20 model) PD-124 board (TRV6/TRV6E/TRV20E model)

2-3

2-3. EVF SECTION (LB-64 BOARD) 1 Raise the finder in the direction of the arrow A, and slide it in the direction of the arrow B. A

2 Two tapping screws (M1.7 × 5)

B

3 Two tapping screws (M1.7 × 5)

2 VF cabinet (upper) assembly

1 Press down the finder and release the two claws.

3

4 VF cabinet (lower) assembly

REMOVING THE LB-64 BOARD 9 VF lens assembly 6 LCD (16P) 7 LB-64 board 1 FP-180 flexible board (27P)

8 LCD cushion (1) 5 LCD cushion (2) 4 BL illuminator 3 LCD cushion (2) 2 Three claws

[LB-64 BOARD SERVICE POSITION] VF lens assembly

AC IN

LB-64 board

AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)

CPC-8 jig (J-6082-388-A)

Adjustment remote commander (RM-95) CN009 1

2

19

20

CPC lid Screw (M1.7 × 4), lock ace, p2

DC IN LANC jack

2-4

2-4. FRONT PANEL BLOCK ASSEMBLY (MA-385 BOARD), CABINET (R) BLOCK ASSEMBLY 2 Screw (M1.7 × 4), lock ace, p2

1 Slide the finder in the direction of the arrow A.

3 Claw

qd Screw (M1.7 × 4), lock ace, p2 4 Top cabinet assembly

qa Screw (M1.7 × 2.5), lock ace, p2

A qj FP-179 flexible board (51P)

qk Cabinet (R) block assembly qs Screw (M1.7 × 2.5), lock ace, p2

5 Screw (M1.7 × 4), lock ace, p2 8 Screw (M1.7 × 4), lock ace, p2

9 FP-188 flexible qh Screw (M1.7 × 4), lock ace, p2 board (28P) qf Press the eject knob in the direction of the arrow C and open the grip cabinet.

B

B

Eject knob 7 Open the jack cover (DC) and jack cover (S).

C

qg Screw (M1.7 × 4), lock ace, p2

6 Screw (M1.7 × 4), lock ace, p2 0 Front panel block assembly

Grip cabinet

REMOVING THE MICROPHONE UNIT, MA-385, SE-107 BOARD

7 SE-107 board 5 Three tapping screws (M1.7 × 3.5)

6 MA-385 board

1 Three claws 2 Tapping screw (M1.7 × 3.5) 3 Microphone retainer 4 Microphone unit

2-5

[MA-385, CK-92/94 BOARDS SERVICE POSITION]

AC IN

AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)

CPC-8 jig (J-6082-388-A) FP-179 flexible board (51P)

DC IN

CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)

Adjustment remote commander (RM-95)

CN009 1

2

19

20

SE-107 board

CK oard B

JK-188 board (28P) Microphone unit

MA-385 board CPC lid Screw (M1.7 × 4), lock ace, p2

Cabinet (R) block assembly

2-5. CK-92/94 BOARD, SPEAKER, CONTROL SWITCH BLOCK (CF30150) qh Two tapping screws (M1.7 × 3.5)

qg Eject knob 5 Control switch block (CF30150) (7P)

4 FP-181 flexible board (6P)

A C

Slant the bottom frame assembly, tripod insulating sheet and tripod table all three parts together, in the direction of the arrow C and remove from the cabinet (R).

qj Control switch block (CF30150)

B CK Bo ar

d

7 Four tapping screws qs Bottom frame (M1.7 × 3.5) assembly A 1 Two tapping qd Tripod insulating sheet screws (M1.7 × 3.5) B

qf Tripod (large)

2 Speaker retainer assembly

2-6

3 Speaker (2P) 8 Two claws

6 Harness (PC-118) (12P) 9 Harness (PC-119) (14P) qa Three screws (M1.7 ), lock ace, p2 with scotch grip.

q; CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)

2-6. DD-137 BOARD, EVF BLOCK ASSEMBLY, BT PANEL SECTION 1 Two screws (M1.7 × 4), lock ace, p2

5 Screw (M1.7 × 2.5) qs Board to board connector (80P)

B

7 EVF block assembly

2 BT panel section

8 CD-252 board (60P) 4 Raise the finder in the direction of the arrow A. A

B

rd

a Bo

-

DD-137

VC

6 Two tapping screws (M1.7 × 5)

qa Screw (M1.7 × 2.5)

3 FP-180 flexible board (27P)

9 Two screws (M1.7 × 2.5)

qd DD-137 board

q; VC heat sink/VC rubber (TRV20/TRV20E model)

[MA-385, CK-92/94, DD-137 BOARDS SERVICE POSITION] FP-180 flexible board (27P)

EVF block assembly

BT panel block assembly

DD-137 board D Bo D-137 ard

DC IN

AC IN

AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)

Extension cable (J-6082-395-A) (80P) CD-252 board (60P)

CPC-8 jig (J-6082-388-A) FP-179 flexible board (51P) CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)

d

oar

-B VC

Adjustment remote commander (RM-95) SE-107 board

CK oard B

JK-188 board (28P) MA-385 board

Cabinet (R) block assembly Microphone unit

2-7

2-7. LENS SECTION-1 (LENS DEVICE, FP-219 FLEXIBLE BOARD) (TRV6/TRV6E/TRV11/TRV11E MODEL) 8 Remove the fourteen solderings

4 Two tapping screws (M1.7 × 5)

1 Screw (M1.7 × 2.5)

2 Control switch block (FK30150) (8P)

2 Two tapping screws (M1.7 × 3.5) 7 Seal rubber (W) A

A

9 CCD block assembly

4 Lens block assembly

5 DC-IN connector

qa FP-219 flexible board 0 Tapping screw (M1.7 × 3.5)

5 Lens device (LSV-650B)

6 Optical filter block 3 FP-219 flexible board (24P)

3 Two tapping screws (M1.7 × 3.5)

1 FP-219 flexible board (50P)

2-8. LENS SECTION-2 (LENS DEVICE, CD-252 BOARD) (TRV20/TRV20E MODEL) 3 Two tapping screws (M1.7 × 3.5)

1 Screw (M1.7 × 2.5)

A

2 Control switch block (FK30150) (8P)

5 Remove the three solderings

A 2 NS-10 board 4 Outer connector (hot shoe) 7 lens frame

6 CD shield case

REMOVING THE LENS DEVICE, CD-252 BOARD 4 Lens block assembly

1 NS-10 board (5P)

q; CD sheet 8 Remove the fourteen solderings

5 DC-IN connector

7 Seal rubber (W) 1 CD-252 board (60P) 3 Two tapping screws (M1.7 × 3.5)

6 Optical filter block 5 Lens device (LSV-690A)

2-8

3 Tapping screw (M1.7 × 3.5)

4 Two tapping screws (M1.7 × 5) qa CD-252 board 9 CCD block assembly 2 Flexible board (from Lens block) (27P)

2-9. VC-240/241 BOARD, MECHANISM DECK 2 Control switch block (FK30150) (39P)

1 JK-188 board (60P)

3 Two screws (M1.7 × 2.5) d

ar

Bo

VC

2 Two claws

REMOVING THE VC-240/241 BOARD, MECHANISM DECK 9 Two screws (M1.7 × 2.5), lock ace, p2

4 Mechanism deck, MD frame assembly, Cassette compartment cover

4

q; Cassette compartment cover 4 Flexible board (from drum motor) (10P) 5 Flexible board (from video head) (10P)

qa Mechanism deck

A

B

A

B

C

D

d

ar

Bo

VC

3 FP-102 flexible board (27P) 8 MD frame assembly

1 Two screws (M1.7 × 2.5)

D C

2 Flexible board (from capstan motor) (27P)

3 VC-240 board (TRV20/TRV20E model) VC-241 board (TRV6/TRV6E/ TRV11/TRV11E model)

1 FP-179 flexible board (51P)

7 Four screws (M1.4 × 1.5)

6 VC-240 board (TRV20/TRV20E model) VC-241 board (TRV6/TRV6E/TRV11/TRV11E model)

2-9

d

ar

Bo

VC

2-10.CONTROL SWITCH BLOCK (FK30150) 4 FP-183 flexible B A board (8P) (TRV11/TRV11E/ TRV20/TRV20E model)

5 Control switch block (PS30150) (6P)

8 Remove 9 in the direction of the arrow C while taking care not to be caught by other parts. 6 Four tapping screws (M1.7 × 3.5) 3 Zoom cover 2 Claws

C 1 Screw (M1.7 × 2.5)

B A 9 Control switch block (FK30150) CS frame assembly

7 Two tapping screws (M1.7 × 3.5)

REMOVING THE CONTROL SWITCH BLOCK (FK30150), CS FRAME ASSEMBLY 4 Control switch block (FK30150)

1 Screw (M1.7 × 2.5) 3 CS frame assembly

2 Dowel

2-11.JK-188 BOARD, CONTROL SWITCH BLOCK (PS30150) PRECAUTION DURING INSTALLATION

REMOVING THE JK-188 BOARD 2 Screw (M1.7 × 2.5)

1 Screws (M1.7 × 2.5) 3 Tapping screw (M1.7 × 3.5) 4 Control switch block (PS30150) 4 JK-188 board

3 Jack frame

1 Tapping screw (M1.7 × 3.5)

2 JK-188 board, jack frame

2-10

To attach, align the switch position as shown.

[Connection diagram for service position (Mainly for voltage measurement and check)] (MA-385, JK-188, CK-92/94, CD-252, FP-219 FLEXIBLE, VC-240/241, DD-137 BOARDS, MECHANISM DECK) Control switch block (PS30150) (6P)

FP-180 flexible board (27P)

EVF block assembly

BT panel section

DD-137 board D Bo D-13 ard 7

DC-IN connector

Control switch block (FK30150) (39P)

Mechanism deck

(TRV20/TRV20E model) NS-10 board

Extension cable (J-6082-395-A) (80P)

CD-252 board

AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)

VC oard B

Lens block assembly

FP-179 flexible board (51P)

(60P)

(TRV6/TRV6E/TRV11/TRV11E)

AC IN

CPC-8 jig (J-6082-388-A) CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)

Lens block assembly

CK oard B

(60P) FP-219 flexible board (50P)

Adjustment remote commander (RM-95)

VC-240 board (TRV20/TRV20E model) Cabinet (R) block assembly VC-241 board (TRV6/TRV6E/TRV11/TRV11E model) (28P) JK-188 board

SE-107 board MA-385 board Microphone unit

2-12.MEMORY STICK CONNECTOR (TRV11/TRV11E/TRV20/TRV20E) Perform the disassembling after steps 1 – 4 of 2-10 is complete. 5 Open it.

A

3 2 FP-183 flexible board Be careful not to be caught by other parts.

4 Push it in the direction of the arrow A.

7 Remove the MS led assembly in the direction of the arrow B. qd Memory stick connector 1 Screw (M1.7 × 2.5) q;

B

6 Release the two engaged portions. 9 Remove the MS chassis assembly in the direction of the arrow C.

2-11

C

qa Remove the eleven solderings. qs FP-183 flexible board 8 Tapping screw (M1.7 × 3.5)

2-13.HINGE ASSEMBLY, LCD HARNESS PROCESSING Start repair work after removing LCD by performing steps 1 – 6 of 2-1 or 2-2 and remove the CK-92/94 board by performing steps 1 – 0 of 2-5. q; Hinge assembly 8 Screw (M1.7 × 2.5)

2 FP-181 flexible board Be careful not to be caught by other parts.

3 Two claws 4 Hinge cover (rear) 2 Screw (M1.7 × 4), lock ace, p2

5 9 FP-181 flexible board 6 Harness (PC-118) (12P)

3 Harness (PC-119) (14P) Be careful not to be caught by other parts.

1 Two screws (M1.7) with scotch grip

4 Harness (PC-118) (12P) Be careful not to be caught by other parts.

7 Harness (PC-119) (14P) 1 Two screw (M1.7 × 4), lock ace, p2 5 Hinge cover (front)

PRECAUTION DURING INSTALLATION (LCD HARNESS PROCESSING)

Extra length is not required in LCD.

Be careful thet harness must not protrude from upper and lower side.

Create an extra length to allow opening and closing.

PDBoard

CKBoard

Allow extra length of this extent in the cabinet.

2-12

2-14.CIRCUIT BOARDS LOCATION

LB-64 (EVF BACK LIGHT)

CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)

DD-137 (DC/DC CONVERTER)

INVERTER TRANSFORMER UNIT

JK-188 (AV IN/OUT)

PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)

VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O

MA-385 (AUDIO I/O)

SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)

2-13

2-15.FLEXIBLE BOARDS LOCATION CONTROL SWITCH BLOCK (FK30150)

CONTROL SWITCH BLOCK (PS30150)

FP-183 (TRV11/TRV11E/TRV20/TRV20E)

FP-181 CONTROL SWITCH BLOCK (CF30150)

FP-182 FP-228

FP-180

FP-100

FP-179

(From LENS BLOCK) (TRV20/TRV20E model) FP-219 (TRV6/TRV6E/TRV11/TRV11E) (CCD IMAGER)

FP-102 From TOP/END SENSOR, TAPE LED (From VIDEO HEAD)

(From DRUM MOTOR) (From CAPSTAN MOTOR)

(From LENS BLOCK) (TRV6/TRV6E/TRV11/TRV11E model)

2-14E

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

SECTION 3 BLOCK DIAGRAMS ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

3-1. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV6/TRV6E) FP-219

VC-241 BOARD(1/3)

(FLEXIBLE)(1/2)

LENS ASSY

J3004 DV IN/OUT

(4-13)

IRIS (SHUTTER)

(4-25)

138 139

IC3000

CCD OUT

8

CCD IMAGER

(4-31)

IC701

CN701

CN3001 17 17

2

30

| (GCAM3) S/H,AGC A/D CONV.

AD0-AD9

|

47

AD SO AD SCK

23

16 CLP OB

CLPDM,PBLK XSHP,XSHD

V DRAIN 6

112

205

203 Y0-Y7

Y0-Y7 207

211

213

215

59

1 C0-C3

3

C0-C3 5

7

56 17 HD,VD,OE

HD,VD OE

71

21

72

23

145

(CAIN)

18

IC702

21

V1-V4,VSHT H1,H2,RG

5

5

9

9

22

TIMING GENERATOR

30

15

42

33

12

CL

HD,VD

44

13 15

132

1

SPCK

M

IRIS HALL +,-

5

37

AFCK(IC903)

196

20 • 19

IC302

I HALL AD

HD VD

184 • 183

(4-29)

IRIS HALL AMP

IC801

50

18 • 17 • 16 • 14

CHARACTER GENERATOR

4

1

COL0 195 • | COL3 194 • 191 • 190

159 VSP SO,SI,SCK

3

75 73 71 105 • 106

31 31

18

67

(4-28)

65

FC A,B FC XA,XB

139 35 35

14

2

4

FOCUS MOTOR DRIVE

21 23

38 38

63

ENO,DIR OA,DIR OB

9

ZOOM MOTOR DRIVE

17 19

28 28

24

7

PANEL R PANEL B

JK-188 BOARD (2/3)

HD,VD EVF G

(4-61)

EVF R EVF B 10 • 11

13

55 59

ENI,DIR 1A,DIR 1B

Y

46

C

7

IC1301

18 14

143 16

22

(TAKO) 144

ZOOM MOTOR

FC RST

137 SPCK (IC751)

ZM RST

ZOOM RESET SENSOR

9

31 • 68

138

39 39

AFCK

2 6

Y C

34

G

S VIDEO

51 47 IR V

IC1001

42

IR L

62

IR R

63

54

L

L

15 VSP SO,SCK

14

30 30

AUDIO I/O

V 55

J3003

49 40

(XYZ)

34 (ALIGN)

20

J3001 G

V

(4-64)

(4-50)

Y

C 31 46

48

36

C

35 50 C

39

(4-48)

IC903

Y

V

24

LINE OUT LINE IN AGC ACC

IC204

CN3001 Y

CN001

12 142

5

25 25

PANEL G

140 141

ZM A,B ZM XA,XB

FRRV,TRRV,TRRT

161

OSD CS OSD SO OSD SCK

M

(SEE PAGE 3-7)

MC BUS 179

52

IRIS DRIVE

2

21

ATF ERR

79

170

44 44

11

TO OVERALL BLOCK DIAGRAM (2/3)

PB CK

48

8 IRIS PWM

EEPROM

M

6

88 81

SPCK(IC751)

38

AD DT 6

182

3

FOCUS MOTOR

REC DT

83

110

IR FSC

42 42

4

FOCUS RESET SENSOR

REC CK

97

111

IC202 IC203

49 49 48 48

6

SFD BCK

(4-36)

IRIS DRIVE +,-

2

H

DATA TO SFD DATA FROM SFD

46

35

(4-25)

37

FRRV,TRRV,TRRT

127

4

(4-27)

CN3000 IRIS METER

MC BUS

49

99

45 X701 36MHz

47

LCK

153

133

11 11 13 13

51 141

11

C4-C7 2

16

42 42

29

156

1

25

9 (LIP) DV INTERFACE

TRCK

152

115 9

1

IC361

CN3001 39 39

DV SIGNAL PROCESS

AD CLK

1

TPA+,TPB+,-

6

42

(4-33)

IC301

CN001

(4-36) 45

L BUS

68

|

X301 24.576MHz

142

201

61

70

V DRAIN 6

199 |

(BIRDS+) CAMERA PROCESS, FOCUS/ZOOM CONTROL, EVR

48 19

IC751

121

11

6

1-4 • 10-13

131

AUDIO/VIDEO

R

R 50 36

59 NIGHT SHOT

CN3001

CN701

A/D CONV. Y0-Y7 43

14

52

JK-188 BOARD(1/3)

8

PITCH SENSOR

66

18

58 58

SFD BCK 47

2

57 57

9 8 12

IC1002 (ADC&DAC) D/A CONV. A/D CONV.

38 HD,VD,OE 37 34

15 16

19 64 17 2

3 2

L R

58

PITCH AD

62

AD SO,AD SCK

23

EXCEPT AEP/UK MODEL 46

ZOOM AD

49

HI SO,SI SCK | 50

CN2051 11

11 11

10

10 10 HI SO,SI,SCK

TO OVERALL BLOCK DIAGRAM (3/3) CN2001

MIC L

1

35

(SEE PAGE 3-10)

IC2002 22

MIC R

3

1

J2001

R

MIC

L

MIC AMP

14

SHOE MIC L SP+,ZOOM AD OSD CS,SO,SCK PANEL R,G,B,EVF R,G,B,HD,VD IR V,IR L,IR R

L 3

3

3

1

1

1

5

5

5

LANC SIG

R

36

3

48

33

(4-105) J2002 LANC SIG

LANC

26

26 26

CN2701

16

MA-385 BOARD(1/2)

3-1

3-2

J3002 L

45 41

25

48

59

SE-94 BOARD

2

R 46 37

SP+,-

63-66 54

1

L R

10

35

YAW AD

MANUAL FOCUS SENSOR

R

53

L R

8

CAM SO,SI,SCK 36

53

YAW/PITCH SENSOR AMP

|

I HALL AD

33

41

CN001

CN3001

12

SE3051

DATA TO SFD

CAMERA CONTROL 40

X801 20MHz

IC3051

YAW SENSOR

IC802

23

(4-89)

SE3052

DATA FROM SFD 49 C0-C7

L

51

IRIS PWM

(4-29) 22

MF A,B

(4-64)

|

L R

HEADPHONE

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

3-2. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV11/TRV11E) FP-219

VC-241 BOARD(1/3)

(FLEXIBLE)(1/2)

LENS ASSY

J3004 DV IN/OUT

(4-13)

IRIS (SHUTTER)

(4-25)

138

X301 24.576MHz

139

IC3000

CN3001

CCD OUT

8

CCD IMAGER

17 17

131

2

30

AD0-AD9

| (GCAM3) S/H,AGC A/D CONV.

47

IC751

|

|

AD SO AD SCK

48 19

CLP OB CLPDM,PBLK XSHP,XSHD

V DRAIN 6

V DRAIN

6

Y0-Y7

|

|

C0-C3

C0-C7

|

|

56

2

29

70

14

28

18 1

IC702

71

13

27

72

12

26

5

5

9

9

22

TIMING GENERATOR

215

7

5

51

| 30

15

42

25

16

33

12

SPCK

10

21

152

23

153

200

202

156

204

206

133

208

212

132

214

216

127

Y0-Y7

49 |

C0-C3

2

4

6

8

13 13

CL

46

MC BUS

49

37

FRRV,TRRV,TRRT

DATA TO SFD DATA FROM SFD SFD BCK

REC CK

99

46

11 11

42 42

29

47

LCK

141

(CAIN)

51 2

9

DV INTERFACE

TRCK

DV SIGNAL PROCESS

17

58

IC361

REC DT

97

45

CN3001 39 39

(LIP)

IC301

3

1 C0-C3

TPA+,TPB+,-

6

42

145

(4-33)

HD,VD OE

1

21

V1-V4,VSHT H1,H2,RG

211

213

115

AD CLK

1

207

32

HD,VD,OE

112

205

203 Y0-Y7

34

(SHIORI) DIGITAL STILL PROCESS

9

L BUS

41

| 17

59

16

23

Y0-Y7

61

(BIRDS+) CAMERA PROCESS, FOCUS/ZOOM CONTROL, EVR

CN001

(4-36) 45

142

201

199

IC1406

24

68

121

11

6

1-4 • 10-13

(4-46)

(4-31)

IC701

CN701

18 HD,VD,OE

44 44

HD,VD

22

110 43

6

4

35

IR FSC

182

5

37

AFCK(IC903)

196

38

SPCK(IC751)

48

(4-25)

AD DT

24

111

45 X701 36MHz

83

6 TO OVERALL BLOCK DIAGRAM (2/3)

88 PB CK

81

ATF ERR

79

(SEE PAGE 3-7)

CN3000 IRIS METER

1

M

IRIS DRIVE +,-

2

8

IC202 IC203

49 49 48 48

IC801

42 42 IRIS HALL AMP

4

3 EEPROM

(4-36)

2

(4-27) 19

1 13

SHUTTER ON

FOCUS MOTOR

M

21

FRRV,TRRV,TRRT

159 VSP SO,SI,SCK 161

3

PANEL G

75

133

PANEL R PANEL B

71 105 • 106

SHUTTER DRIVE

5

11

COL0 195 | • COL3 194 • 191 • 190

31 31

18

M

MC BUS 179

OSD CS OSD SO OSD SCK

15 7

184 • 183

73

IC201

17

FOCUS RESET SENSOR

18 • 17 • 16 • 14

CHARACTER GENERATOR

4

44 44

(4-27)

HD VD

52 50

IRIS HALL +,-

6

20 • 19

IC302

I HALL AD

(4-29)

IRIS DRIVE

H

170

IRIS PWM

EVF G

139 35 35

14

2

4

38 38

21 23

25 25

5

FOCUS MOTOR DRIVE

15

ENO,DIR OA,DIR OB

9

140

AFCK (IC1903)

28 28

24

13

ZOOM MOTOR DRIVE

17 19

(4-50) 10 • 11

CN001

12 Y

55 115

142 7

EVF B

63

141 ZM A,B ZM XA,XB

(4-61)

EVF R

65

FC A,B FC XA,XB

JK-188 BOARD (2/3)

HD,VD

67

IC1301

46

C

59

ENI,DIR 1A,DIR 1B

7

143 144

IC204 ZOOM MOTOR

FC RST

137

ZM RST

96

138

39 39

9

VSP SO,SCK

112

(4-28) ZOOM RESET SENSOR

LINE OUT LINE IN AGC ACC

113

74

85

103

80

72

60

94

Y

2

IC903

C

6

34

42

IR V

IC1001 15

VSP SO,SCK A0-A11

CN701 14

22

JK-188 BOARD(1/3)

43

CN3001

12

SE3051 8

PITCH SENSOR

DATA FROM SFD 31

1

13 • 38

48

49 DATA TO SFD C0-C7

66

I HALL AD

| SFD BCK

IC752

47

18

58 58

2

57 57

35

62

58

PITCH AD

IC1002 (ADC&DAC) D/A CONV. A/D CONV.

15 16

L

J3003

49 40 V

55

AUDIO/VIDEO

R 50 36

19 64 17 2

3 2

L

R

R

L

R J3002

46 37 L

R 45 41

HEADPHONE

25 23 8

SP+,-

10

(4-48)

(4-32)

L

53

L R

37

63-66

AD SO,AD SCK

EXCEPT AEP/UK MODEL

54 YAW AD

12

HD,VD,OE

16Mbit SDRAM

CAM SO,SI,SCK

36

53

YAW/PITCH SENSOR AMP

9 8

38 34

L

R

51

52 18

33

41

CN001

(4-64)

|

CAMERA CONTROL 40

X801 20MHz

IC3051

YAW SENSOR

IC802

23

(4-89)

SE3052

14

AUDIO I/O

IRIS PWM

(4-29) MF A,B

IR R

63

A/D CONV.

D1-D10 Y0-Y7

IR L

62

54

(ALIGN)

59 CN3001

S VIDEO

G

51 47

30 30

20 NIGHT SHOT

J3001 G

V

(4-64) 48

Y

C

24

36

C

35 50 31 46

(XYZ)

34

AFCK

Y C V

39

31 • 68

SPCK (IC751)

14 22

(TAKO)

16

18

CN3001 Y

4 46

ZOOM AD

49

L R

48

59

KASYA ON

HI SO,SI SCK |

SE-94 BOARD

50

(4-45)

(4-45)

171 • 172 • 178

CN2051 MANUAL FOCUS SENSOR

1

11

11 11

2

10

10 10

IC1405 HI SO,SI,SCK

IC1407

16Mbit SDRAM

(4-44)

IC1404

4Mbit FLASH

160 TO OVERALL BLOCK DIAGRAM (3/3) CN2001

MIC L

1

35

(SEE PAGE 3-10)

IC2002 22

MIC R

3

1

MIC AMP

14

L

SHOE MIC L 19 SP+,-

2

12

1

8

39

49

16

24

32

29

(KATHMANDU) DIGITAL STILL CONTROL

45

ZOOM AD

3

A1-A19

PANEL R,G,B,EVF R,G,B,HD,VD

R

MIC

L

1

5

5

5

RXD TXD

(4-105)

232C ON

J2002

IC1403

Q1111 LANC SIG/232C RD

LANC/ DIGITAL I/O

26 LANC GND/232C TD 24

14

23 23

RS232C I/F

181 175

9

12

26 26

7

RXD

5

24

4

23

2

(SEE PAGE 4-91)

TXD

CN2701

MA-385 BOARD(1/2) 16

3-3

CN062 26

CONTROL SWITCH BLOCK (FK-30150) (1/2)

| 35

(4-39)

48

33

MS DIO,MS SCLK,MS BS

53

36

3

193 192

D0-D15

J2001

194

LANC SIG 1

CN008

| 79

3

1

X1401 25.8048MHz

57

OSD CS,SO,SCK

IR V,IR L,IR R 3

R

161

3-4

MEMORY STICK

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

3-3. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV20/TRV20E) CD-252 BOARD(1/2)

VC-240 BOARD(1/3)

IC751

(4-23)

LENS ASSY

J3004

(CARILLON)

DV IN/OUT

138

(4-11)

IRIS (SHUTTER)

(4-11)

13

(4-17)

9

PLL

IC101

IC104

CCD OUT 8

CCD IMAGER

5

11

CDS, AGC

4

2

2

36

4

4

32

SPCK

199

201

203

205

207

211

213

215

142

16

1,13,14

|

|

145

Y0-Y7

65

1 |

IC301

3

C0-C3 5

7

(CAIN)

248

16,17,22

HD,VD OE 60

34

26 26

61

35

25 25

62

15 15

57

23

256

(4-11)

IC102

MCK

25

RC PROCESS

200

202

156

204

206

133

208

212

132

214

216

127

33 Y0-Y7

| 25

29

TIMING GENERATOR

30

(TRV20) 54MHZ(TRV20E)

(4-17)

IC702

18 18

DRAM 18 |

A0-A11

2

16Mbit SDRAM

22 22 CN101

C0-C3

|

109

20

|

16

122

H

ND FILTER METER

17

43 43

IRIS HALL +,-

IC202 IC203 IRIS DRIVE

I HALL AD

25

M

27

DQ0-DQ15

182

89

AFCK(IC903)

196

|

SPCK(IC751)

48

26

19

60 60

20 • 19

18 • 17 • 16 • 14

CHARACTER GENERATOR

42 43 45

1

HD VD

184 • 183

8

F MR A,B

9

FOCUS MOTOR

M

3

M

2

FOCUS +,-

4

ZOON +,-

1

39 39

7

40 40

17

ND FILTER PRE DRIVE

13

36 36

23

35 35

2

34 34

21

SHUTTER DRIVE

PWMO EN0

10

VSP SO,SI,SCK 161

12

(4-22)

32

105 • 106

MR

21

Z MR A,B

19

IC803

Y0-Y7

1

28

46

27

213 233

EVR

|

12 15

EVF G (4-61)

EVF R

65

EVF B

63

10 • 11 Y

55

46

C

59

7

(TAKO)

49

LINE OUT LINE IN AGC ACC

47 38

2

236

37

6

234

36

Y C

48

26

IC801

IR V

IC1001

2 CN101

(4-64)

CN701 37 14

43

(4-21) MF A,B

22

JK-188 BOARD(1/3)

46

IC802

23

65 66

IRIS PWM

IC3051

SE3052 12

YAW SENSOR SE3051

8

PITCH SENSOR

165

SFD BCK |

|

IC1404 CAM SO,SI,SCK

A0-A13

58 58

2

57 57

JID0-JID7

|

AD SO,AD SCK

193 13 • 42

58

62

ZOOM AD

D0-D15

X1401 6,875MHz

|

|

77

212

145

79

|

83

SYSCLK

(4-40) 27 34

CN2051

IC1407

JID0-JID7 11

11 11

2

10

10 10

41

JPEG

18 TO OVERALL BLOCK DIAGRAM (3/3)

(4-105)

CN2001 1

35

22

MIC R

3

1

J2001

R

MIC

L

(SEE PAGE 3-10)

IC2002 MIC AMP

3 33

14

L

19

2

21

4

3

HEADPHONE

SP+,-

4 46

6 49

(4-39)

DI,CI

109

DIGITAL STILL CONTROL

1

L R

50

IC1408

TXD RXD

4

SHUTTER SOUND

2

112

IC1412

(4-40)

16Mbit DRAM FAST PAGE

2,9-16 58-64

5-15

51

1-13 38-48

20-31

62-75

28

(4-40)

SHOE MIC L SP+,-

36 A0-A10

ZOOM AD

|

10

15

26

5

|

|

24

4

17

23

2

1

1

1 • 48

5

5

5

26

26 26

12

24

23 23

14

D0-D15

36

(4-39)

48

IC1410

232C ON

40 SCK

13

XTAL OSC 9

RS232C I/F

MEMORY STICK I/F

|

X1402 20MHz 2 4

IC1403

Q1111

7

TXD

CONTROL SWITCH BLOCK (FK-30150) (1/2) (4-69)

RXD

(4-42)

CN2701

MA-385 BOARD(1/2)

3-5

CN062

CN008

38

PANEL R,G,B,EVF R,G,B,HD,VD

1

LANC GND/232C TD

(4-42)

IC1409

OSD CS,SO,SCK

LANC SIG

LANC SIG/232C RD

16

J3002 L

45 41

23

EEPROM

3

R

J2002 LANC/ DIGITAL I/O

R 46 37

R

25

SPCK1(IC751)

IC1406

IR V,IR L,IR R 3

R

2

L

SYSCLK(IC1412) HI SO,SI,SCK

MIC L

L

3

R

IC1411

50

1

64 17

8

|

SE-94 BOARD

50 36 L

10

53

MANUAL FOCUS SENSOR

19

R

J3003 AUDIO/VIDEO

R

54-52

48

59

55

R

53

L

(4-40)

154

L 49 40 V

2

D/A CONV. A/D CONV.

A0-A10

2

54

PITCH AD

16

(ADC&DAC)

HI SO,SI SCK

181

|

YAW AD

12

|

155

18

8

130 35

64Mbit SDRAM

35 53

YAW/PITCH SENSOR AMP

20

15

IC1002

9

161 34

41

CN001

138

(4-41)

I HALL AD

33

40

X801 20MHz CN3001

DATA FROM SFD SYSCLK(IC1412) DATA TO SFD

CAMERA CONTROL

(4-89)

36 143

ND HALL AD

L

51

VSP SO,SCK

(4-21)

ND PWM

AUDIO I/O

14

EEPROM

38 38 CN151

IR R

63

54

3 5

IR L

62

(XYZ) 15

63-66

NIGHT SHOT

S VIDEO

G

51 47

42

(4-50)

J3001 G

V

(4-64) 39

Y

C 31 46

V

24

34

C

Y 35 50

C

14

36

CN3001

Y

18

22

52

HD,VD,OE

4

CN001

IC1301

|

C0-C7

237

52 52

IC903

JK-188 BOARD (2/3)

HD,VD

67

|

224

50 50

(4-48)

A/D CONV.

17

(4-19)

PANEL B

71

59

222 |

16

PANEL R

73

(ALIGN)

SPCK1(IC751)

FOCUS/ ZOOM MOTOR CONTROL

31

PANEL G

75

34

223 23

34 PWM1 EN1

11

31 • 68

(4-19)

IC204

33

IC201 ZOOM MOTOR

SPCK (IC751)

14

ZOOM MOTOR DRIVE

4

33 33

15

FRRV,TRRV,TRRT

159

COL0 195 | • COL3 194 • 191 • 190

OSD CS OSD SO OSD SCK

SHUTTER ON

9

(SEE PAGE 3-7) MC BUS

3

IRIS COM

15

FOCUS MOTOR DRIVE

TO OVERALL BLOCK DIAGRAM (2/3)

ATF ERR

179

AFCK

MR

6

PB CK

170

ND PWM ND FILTER DRIVE

AD DT

88

79

ND HALL AMP 5

REC DT

83

8

ND HALL AD

59 59

REC CK

81

(4-36)

IC205

55 55 ND DRIVE +,-

SFD BCK

99

6

(4-19)

57 57

23

8

IR FSC

48

IRIS HALL AMP

H

DATA TO SFD DATA FROM SFD

24

18 1

IC302

48 48 ND HALL +,-

4

6

22

17

| IRIS PWM

47 47

16

FRRV,TRRV,TRRT

107

(4-19)

13

37

97

CN701 13 • 38

M

MC BUS

49

18

|

44 44

2

CAM SO,SI,SCK

20 20

47

IRIS DRIVE +,-

47

LCK

HD,VD,OE 31

12

42 42

29

24 X101 66MHz

1

IRIS METER

51 141

153

HD,VD,FLD CAMERA SIGNAL PROCESS

9 (LIP) DV INTERFACE

TRCK

152

21

| 23 23

33

CN3001 39 39

DV SIGNAL PROCESS

17

253

AD SO,SCK

42

(4-33)

251

47 48

TPA+,TPB+,-

6

IC361

L BUS

|

AD0-AD9

11

CLPDM, XSHP,XSHD

V1-V4 RG,H1,H2 40-42,44,45, 9,12,13

45

247 A/D CONVERTER

CN001

(4-36)

78

2

238 1-4,10-12,14

X301 24.576MHz

139

10

IC701

CCD OUT(+) CCD OUT(-)

SPCK1

3-6

MEMORY STICK

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

3-4. OVERALL BLOCK DIAGRAM (2/3)

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. CN009 FOR ADJUSTMENTS 17 SWP

VC-240/241 BOARD(2/3)

(SEE PAGE 4-55) (4-38)

RF MON

REC CK

REC CK

REC DT

REC DT

40

IC102

42

(TRW)

(4-37) 42 AD DT

AD DT

6

6

PB CK

PB CK

ATF ERR

ODD

7

REC/PB AMP

5 6 DRUM

2

27

EVEN

1

8 9

(TRF) EQ A/D CONV. PLL

13

22 24

34

(SEE PAGE 3-2,3-4, 3-6)

PB Y OUT

CN101 6

IC101

15 20

TO OVERALL BLOCK DIAGRAM (1/3)

(4-52)

J MECHA DECK

20

31

SWP

95 60

SWP

78 |

(4-59)

MC BUS FRRV TRRT,TRRV

IC501

VSP SO,SI,SCK

MECHA CONTROL

(4-60)

2-4

M902 CN007

115 45

32

CAP FG

CN002 69

CAP PWM

56

IC401

| (RABI) 108

(4-107)

CN1603

54

CN1603

68 68

18

(2/2)

IC1601

SWITCHING 66 66

61

PWM DRIVE DRUM PWM

52

53

CAP VS

62 62

18.22

(SEE PAGE 3-10)

HI SO,SI,SCK

CAPSTAN MOTOR

11

(4-56)

| 14

58 58

DRUM VS

SWITCHING 58

60 60

(RABI) DRUM MOTOR DRIVE

11

LPF

TO OVERALL BLOCK DIAGRAM (3/3)

M

1 | 4

(4-55)

IC401

Q1611

DRUM ERROR 22

1

21,23,19

(2/2)

|

X501 20MHz

FG

17 | 20

CAPSTAN MOTOR DRIVE

CN002 64 64

CAP ERROR

LPF

68

25

Q1610

74

76

CAPSTAN

IC402

(4-55)

37 106

CAPSTAN FG AMP

2,3

| FRRV TRRT TRRV

14,15

CAP ON,CAP FWD

46

26

IC502 EEPROM

DRP SO,XDRP SCK

80

DD-137 BOARD(1/3)

CN005

M901 5

20,21,24

2

DRUM MOTOR

M

| 10

(1/2)

2

DRUM FG

1

DRUM PG

47 DRUM ON,DRUM FWD,DRUM START

83

48

82

63

16,6,3

81 116

DRUM FG

1

DRUM PG

59

DRUM FG AMP

64

CHIME SDA,CHIME SCK,CHIME VDD XCC DOWN

117

61 DRUM PG AMP

CN006 1

49

LOAD,UNLOAD

26,25

50

114 113

54

53

96

LOADING MOTOR DRIVE

28,30

|

M

M903 LOADING MOTOR

4 TREEL FG

40

SREEL FG

48

TAPE END

34

42,43 REEL FG AMP

45,46

5

35 TAPE END DETECT

TAPE TOP

36

37 TAPE TOP DETECT

DEW SENSOR

20

T REEL

21

SENSOR

24

S REEL

23

SENSOR Q902

DEW DET

TAPE END SENSOR 25

55

TAPE LED ON Q901 TAPE TOP SENSOR

44

39

27

REC PROOF SW

D901 TAPE LED

MODE SW A - MODE SW D

| 42

12

REC PROOF 15

S901

7 |

4PIN CONNECTOR

CN901

9 XCC DOWN 11

S903 C IN

16 MODE |

Note : VC-240 BOARD : DCR-TRV20/TRV20E VC-241 BOARD : DCR-TRV6/TRV6E/TRV11/TRV11E

S902

16

3-7

SWITCH

18

3-8

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

3-5. OVERALL BLOCK DIAGRAM (3/3)

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. Note : VC-240 BOARD : DCR-TRV20/TRV20E VC-241 BOARD : DCR-TRV6/TRV6E/TRV11/TRV11E

9

FP-181

CK-92/94 BOARD(1/2)

(FLEXIBLE)

PANEL REVERSE SW

3

4

4

CAMERA FUNCTION SW MEMORY FUNCTION SW PANEL CLOSE SW MENU SW DISPLAY SW DATA CODE SW

AD4X

CN3204

7

CK-94 BOARD (2/2)

(4-62)

IC1104

CN003 3

11 10

VC-240/241 BOARD(3/3)

S3201-3216 CN96

S97

PD-123 BOARD(REF.NO.2000 SERIES): TRV11/TRV11E/TRV20 PD-124 BOARD(REF.NO.3000 SERIES): TRV6/TRV6E/TRV20E

CN009 FOR ADJUSTMENTS

13 39

97

KEY AD4

99

KEY AD6

15 37

HI CONTROL

17 35

CN3205 XCS OSD

44

OSD SO XOSD SCK

45

1 2

PD-123/124 BOARD

51

OSD SO,SCK

1

50

8

1

2

46

IC2171 IC3171

CN3171 CN2176

CN3201

(4-93/4-97)

LCD DRIVE

7

2

11

1

30

20

9

9

12

12

LCD INDICATOR

CN2175 CN3173

PANEL VG 13 39

COM1-4 SEG1-16

PSIG 27 25 PANEL COM

CONTROL SWITCH BLOCK(CF-30150)

15 37 CHIME SDA CHIME SCL

S103-106 LCD BRIGHT SW VOLUME SW

6

5

100

19 33

6

96

11 41

5

CHIME AD0

71

CHIME AD2

73

KEY AD7

KEY AD3

XCC DOWN

4

4

3

3

1

51

67

DIAL A

3

49

68

DIAL B

CN3203

CN100

S3218 21 31

(SEE PAGE 4-83)

RESET

38

5

(4-96/4-99)

8

48

9

43

7

7

47

7

45

6

6

46

CHIME SDA CHIME SCK CHIME VDD

40

XCC DOWN

18

HI SO

33

HI SI

34

XHI SCK

35

TO OVERALL BLOCK DIAGRAM(2/3)

(SEE PAGE 3-7)

BATT LI 3V

3

CN3205

7

IC1102

21 31

9

9

22 30

10

10

45 42

(4-61)

51

6

LANC IN

1

10

LANC OUT

2

12

VDD 77

IC1103

VDD SWITCH

HD 17 35

1

1

1

2

2

48

LANC SIG

CN2173 CN3172

11

LANC I/O

(4-61)

CONTROL SWITCH BLOCK(FK-30150) (2/2)

CN008

X1101 20MHz

40

X1102 32.768KHz

52

IB SI

48

53

IB SO

49

41

Q1104

S1

2

1

1

XCAM STBY SW

POWER SW

4

3

3

XVTR MODE SW

BATT/EXT SW

66

1

5

5

XPHOTO STBY SW

FAST CHARGE

50

S2 START/STOP SW

5 CN064

4

16

XS/S SW

21

17

XEJECT SW

S61

(SEE PAGE 4-91)

EJECT SW

VTR DD ON

29

CAM DD ON

28

SHOE ON

81

VTR FUNCTION SW LASER LINK SW

14

94

KEY AD1

18

93

KEY AD0

36

SIRCS ENV

59

46

6

48

4

SP+,-

KEY AD2 19

10

XPHOTO FREEZE SW SIRCS SIG

47

4

9 PWM

PANEL 4.6V Q2172,2173 Q3171,3172

P UNREG

DD-137 BOARD (3/3)

LB-64 BOARD 3

6

25

3

4

26

2

8

8

24

4

2

2

27

1

10 10

23

5

5

14

14

14

R,G,B 2 4 COM

12

1

14 14 CN2202

95

45

HI SO,SCK

4

16 16

(4-54)

24

IC1803

18 18

1

(4-86)

20 20 14

42 TIMING GENERATOR

48 9

1

1

3

3

5

5

7

7

IC2201 EVF BL 4.6V

Q2201 INVERTER PWM

17 17 36

3

25

8

20

7

21

ND2201 BACK LIGHT

BACK LIGHT DRIVE

EVF BL + 24 24

37

R1693,1694

SHOE UNREG 38

EVF BL -

EVF BL 4.6V

22 22 CN1603 CN2201

CN1604 BATT SIG EVF BL+

73 73 BATT/EXT SW

2 75 75

EVF BL-

71 71

EVF VG

76 76

EVF VCO

FAST CHARGE

3

BATT UNREG J1602 BATTERY TERMINAL

4

CN009 FOR ADJUSTMENTS

5 TRV20/TRV20E

70 70

S

VTR UNREG

2

VTR UNREG

72 72 3

74 74

Q1602

65 65 67 67

1 DC IN

(4-107)

IC1601 IC1602

2 3

DC/DC CONVERTER

CN701

A 3.1V

P UNREG 80 80

D 1.5V

CN152

OSD,CS,SO,SCK

A 2.8V

MA-385 BOARD(2/2)

SHOE ON 27 27

AU 2.8V

HI,SO,SI,SCK TO OVERALL BLOCK DIAGRAM(1/3)

Q1626 30 30

CAM -7.5V

ZOOM AD SHOE UNREG

32 32

CAM 15V CN1603

SHOE MIC L CN002

LANC SIG

PANEL -15.3V

28

30 30

S2061 FOCUS SW

JK-188 BOARD (3/3)

(SEE PAGE 3-1,3-3,3-5)

IR V,IR L,IR R

PANEL 4.6V 15 15

PANEL/EVF 2.8V

1

15

REMOTE COMMANDER RECEIVER

TRV6/TRV6E/TRV11/TRV11E

FP-219

EVF 13.3V RP 4.6V

(FLEXIBLE)(2/2)

IR V IR L

A 4.6V

IR R S3000

AU 4.6V

SIRCS PWM SUPER NIGHT SHOT SW

EVF BL 4.6V

3-9

41 46 48

IC1901 IR TRANSMITTER

18

IR DRV EM

22 7

IR FSC

( IC301

S2071-2074

196 )

50 50 CN3001

16

18 18 CN701

(4-105)

IC2091

SIRCS SIG

PANEL 13.3V

DD-137 BOARD (2/3)

SUPER NIGHT SHOT SW

3 CN101

PANEL R,G,B EVF R,G,B HD,VD,SP+,SP-

78 78

D 1.9V

MT 4.9V

S001

31 31

D 3.1V

D 2.8V

NS-10 BOARD

CD-252 BOARD (2/2)

VTR DD ON CAM DD ON

CN1601

BACK LIGHT DRIVE

5

4

LANC SIG

CN1602

2

6

31

1

INVERTER BLOCK

22

MOD

1

(SEE PAGE 4-91)

1

20

24

RGB DRIVE

SHOE MIC L

8

CN3101

CN3174 CN2174

12 12

VD

7

18 22

24

39

HD

INTELLIGENT ACCESSORY SHOE

12

CN2101

2

SP901 SPEAKER

CN002

IC1802

46

8

2

1

(4-54) 48 EVF R,G,B

RV51 ZOOM VR

2 7 8 10 12 13 12 19

BL ON

2

46

PHOTO SW

6

CN003

BATT SIG

PHOTO REC S71

LCD UNIT

I/F

Q1102,1105 SIRCS CARRIER

3

PSIG

HD OUT

40

S62-70,72

5

21 11

TIMING GENERATOR

CN3206

87

CONTROL SWITCH BLOCK(PS-30150)

27

IC2105 IC3102

46

42

4

20

VCOM

(4-96/4-99)

VD 50

24

CN3202

16 36 2

19 VR,VG,VB

22

5

HI SO,SCK

XRESET

20

RGB DRIVE

39

RESET BT3201 LITHIUM BATTERY

IC2104 IC3101

PANEL R,G,B

HI SO,SI,SCK

DIAL

11

8

6

S102

CONTROL

10

11

11 41

5

S100,101 PROGRAM AE SW EXPOSURE SW

10

26 26

XHD OUT

CK-92 BOARD : TRV11/TRV11E/TRV20 CK-94 BOARD : TRV6/TRV6E/TRV20E

(4-52)

CN001

18 CN3001

3-10

LED DRIVE CN2071

D2701,2072

LCD UNIT

ND901 BACK LIGHT

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

3-6. POWER BLOCK DIAGRAM (1/2) PD-124 BOARD

*1 : DCR-TRV6/TRV6E/TRV11/TRV11E *2 : DCR-TRV20/TRV20E

DD-137 BOARD

IC3101

BATT SIG 73

Q1625, 1626

J901 BATTERY TERMINAL

RGB DRIVE

SHOE ON 27

SHOE UNREG

(4-61)

INIT CHARGE ON 69 VTR DD ON 65 CAM DD ON

(4-99)

67

CN1602

CN3171

1

FAST CHARGE

F1601

BATT UNREG

71 BATT/XEXT SW

PANEL 4.6V

75

8

Q3103

7

Q1601, 1602

F1602

Q1603, 1604

3

L3101

PANEL 13.3V 6

BATT SIG

2

P UNREG

76 Q1615-1617,1624

12 POFF

IC3171

70 VTR UNREG 72

F1603

ACV UNREG

1

TIMING GENERATOR

74 30

SHOE UNREG

2 BATT/XEXT

4

(4-99)

MT 4.75V 55 57

32

3 CN1601

BLON

LCD INDICATOR DRIVE

2

INVERTER BLOCK

5

BACK LIGHT DRIVE

Q3171,3172

CN3174

INIT CHARGE ON

(4-97)

LF1601

SHOE ON

CN3172

53

MT 4.9V

F1604

J902 DC IN

IC3102

EVER 3.0V 5

4.9V REG

F1605

CN3101

14

BATT UNREG

BATT UNREG

F1606

CHARGE SWITCH

18

BATT FET ON

TO POWER BLOCK DIAGRAM (2/2) (CK-94)

S

LCD UNIT

PANEL 2.8V 5

78

IC1601

Q1606, 1607 D1609

TRV6/TRV6E/TRV20E

DC/DC CONVERTER

EMERGENCY DETECT

T1601

(4-107)

P UNREG

80

Q1612 SWITCHING

TRV11/TRV11E/TRV20/TRV20E L1604

L1608

A 3.1V

L1607

D 3.1V

PANEL 2.8V 23 PANEL -15.3V 25 PANEL 13.3V 26 PANEL 4.6V

5 D1607 RECT

PD-123 BOARD

VCC(0)1234

OUT7-1

64

2

VCC(0)5678

OUT7-2

1

28

VCC

-IN7

IC2104

28

Q1621 SWITCHING

EVF 13.3V 19

13

43 AU 4.6V 44

RGB DRIVE

Q1613 SWITCHING

7

(4-96) 8

CN2173 CN2101

TRV20

L2104

PANEL 4.6V 8

LCD UNIT

23 PANEL -15.3V

7

4

3

L2103

PANEL 13.3V

1

6 P UNREG

2

1

(4-96)

12

VSS(0)1234

57

VSS(0)567

3

46 L1608

L1605

49

VDD(0)123

60

VDD(0)567

OUT3-1

53

OUT3-2

54

IC1602

Q1622 SWITCHING

CN2176

28

8

+IN8

7

-IN8

IC2171

3

TRV11/TRV11E

OUT8

INVERTER BLOCK

5

BACK LIGHT DRIVE

Q2172,2173

(4-93)

AU 2.8V 48 D 1.5V 49

54

Q1614 SWITCHING

OUT2-1

50

OUT2-2

51

-IN2

BLON 2

L1606

L1612

AU 2.8V

L1610

A 2.8V

L1609

Q1623 SWITCHING

D1610,1613 -15.3V REG

VREF

27

56

4

5

1

6

-IN4

37

33

VB

34

RT

35

VTR DD ON

IC2201

COMP

11

CT

OUT1-1

47

OUT1-2

48

-IN1

44

RP 4.6V CAM 15V(*2)

L1617

PANEL 13.3V

L1618

D1612 RECT

EVF 13.3V

*1

D1611(2/2) RECT

EVF 13.3V CAM -6.5V(*1) CAM -7.5V(*2)

Q1635,1639,1643

3

Q1609 SWITCHING

-6.5V/-7.5V REG

*2 L1603

L1615

Q1618 SWITCHING

PANEL 4.6V

L1614

A 4.6V

L1616

RP 4.6V

L1613

AU 4.6V EVF BL 4.6V

29

CTL1-6,8

30

CTL7

CAM DD ON Q1610 SWITCHING

L1601

CAP VS

INVERTER

CAM 12V(*1)

12V REG CN1604 21

R1693,1694

7

20

8

17

11

EVF BL 4.6V

A 4.6V

46

*2

8

D 3.1V

40

41

*2 OUT4

2

LCD UNIT

38

EMERGENCY DETECT

D1611(1/2) RECT

VREF

TRV11/TRV11E/TRV20

BACK LIGHT DRIVER

EVF 2.8V PANEL -15.3V

44 T1602

OUT6-1

61

OUT6-2

62

+IN6

18

Q1619 SWITCHING

Q1647,1649, 1650,1653 *1

EVF 13.3V EVF VCC

16

EVF 2.8V CN1603 11

22 24

19

CAP ERROR Q1611 SWITCHING

CN2201

CN2202

64 L1602

CAP VS

66

DRUM VS

CAP ERROR

21 68

LB-64 BOARD

11

22 24

19

21 L1803

CN002

OUT5-1

58

OUT5-2

59

+IN5

22

58

Q1620 SWITCHING

DRUM VS

60 DRUM ERROR 62

DRUM ERROR

CN009 FOR ADJUSTMENTS

EVF BL+

3-11

IC1803

RGB DRIVE

TIMING GENERATOR

CAM 12V(*1) CAM 15V(*2) 36

CAM -6.5V(*1) CAM -7.5V(*2)

2 EVF BL3

16

IC1802 (4-54)

VC-241 BOARD(1/2) VC-240 BOARD(1/2)

TO POWER BLOCK DIAGRAM (2/2) (VC-240)*2 (VC-241)*1

(SEE PAGE 3-13,3-15)

PANEL 2.8V Q1632,1637 1641

43

Q1608 SWITCHING

D 1.5V

D 2.8V

Q1629

(4-86)

D 2.8V

56

L1611

RECT

CN2174

A 2.8V

47

40

Q1605 SWITCHING

LCD INDICATOR DRIVE

D 1.9V

51

Q2102 2106 2103

XC SAVE

4

(4-109)

1.5V REG -IN3

45

Q1627,1628

5 TIMING GENERATOR

50

D 1.9V

52

D1606 RECT

IC2105

EVER 3.0V

46

D1608 RECT

24

L2102

PANEL 2.8V 5 TO POWER BLOCK DIAGRAM (2/2) (CK-92)

55

34

(4-54)

A 3.1V 42

*1 *2

CN1603

3-12

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

3-7. POWER BLOCK DIAGRAM (2/2) (DCR-TRV6/TRV6E/TRV11/TRV11E) VC-241 BOARD(2/2)

CN008 38

SHOE UNREG 8

IC1104

37

(4-62)

INTELLIGENT ACCESSORY SHOE

TRV11/TRV11E

HI CONTROL MS VCC 28 SHOE ON BATT SIG INIT CHARGE ON VTR DD ON CAM DD ON FAST CHARGE BATT XEXT SW BATT UNREG

27 73 69 65

IC1102

(4-61)

67 71 75

IC1101

D1103

76

REG

2

ACV SENS

IB SO

49

IB SI

48

INIT CHARGE ON

25

VTR DD ON

29

5

XRESET

38

3

31 42

6

54

7

IC1103

BATTER IN DETECT

REG

51

63 87

VDD

4

(4-61)

61

CAM DD ON

28

FAST CHARGE

50

POWER

4

MT 4.75V KEY ILLUMINATION LED

17 RV51 D 2.8V

7

ZOOM VR

BATT/XEXT

66

XVTR MODE SW

14

3

4

XCAM+STBY SW

15

1

2

XPHOTO STBY SW

20

5

1

LANC I/O UNREG

1

BATT SIG I/F

12

CONTROL SWITCH BLOCK(FK-30150)

CN064

BATT IN

8

70 72

MEMORY STICK

1 CN062

Q1104

D62-70

D1102

55

VTR UNREG

81

15

D1104 53 MT 4.75V

91

SHOE ON

(4-61)

RESET 3

90

BATT SENS

OFF

LANC DC

14

VCC

S1

CAMERA

POWER

MEMORY

TRV11/TRV11E

XLANC ON

Q1106

74

CONTROL SWITCH BLOCK (PS-30150)

VCR

8

D 2.8V

CK-92/94 BOARD

7

CHIME PWR CONT

92

VTR DD SENS CN003

Note : CK-92 BOARD : TRV11/TRV11E CK-94 BOARD : TRV6/TRV6E PD-123 BOARD : TRV11/TRV11E PD-124 BOARD : TRV6/TRV6E

S100-106 D 2.8V

SHOE UNREG

7

40 12

30

SHOE UNREG 31 21

P UNREG

50

78

PANEL 2.8V

PANEL 13.3V PANEL 4.6V

2

VTR UNREG

21

PANEL 4.6V 8

38 14

25

PANEL 2.8V Q1011

26

REG

5

32 20

LANC DC

PANEL -15.3V 7

36 16

28

PANEL 13.3V 6

25 27

EVF 13.3V

19

(4-64) 43 AU 4.6V

SW

CONTROL SWITCH BLOCK(FC-30150)

BT3201 LITHIUM BATTERY

34 18 EVF 13.3V

7 CN100

RESET

BTT LI 3V

80 PANEL -15.3V

CN3203

S3218

31

44

IC1002

(XYZ) AUDIO I/O

AUDIO ADC&DAC

12

24 28

(4-64)

IC1001

P UNREG

TO POWER BLOCK DIAGRAM (1/2) (PD-123/124)

CN3202 EVER 3.0V 5

5

47 CN3201

CN3205

46

IC502 50

IC501

52 45

(4-60)

A 2.8V

XREEL HALL ON

D2071,2072

JK-188 BOARD CN001 21 21

5

AU 2.8V TO POWER BLOCK DIAGRAM (1/2) (DD-137)

D 2.8V

AU 2.8V

48

(4-105)

12

IC002

D 1.5V

9

9 A 4.6V

D 2.8V

MIC AMP

13 13

13 LANC DC

51

28 28

(4-106)

27

(4-33)

54

CN2071

56

(SEE PAGE 4-12)

59 59

EVER 3.0V

IC2091

A 2.8V

60 60

IC903 D 3.1V

IC1301

IC301

IC361

(ALIGN)

(TAKO)

(CAIN)

(LIP)

A/D CONV.

VIDEO LINE IN/OUT AMP

DV SIGNAL PROCESS

DV INTERFACE

38

IC302

IC1901

CHARACTER GENERATER

IR TRANSMITTER

RP 4.6V

44

A 4.6V

46

D 3.1V

(4-48)

(4-50)

(4-36)

J2002 SE3501,3502

PITCH,YAW SENSOR AMP

MA-385 BOARD

FB753

(4-55)

TRV6/TRV6E

MT 4.75V

(4-56)

D 1.9V D 2.8V

IC401

IC402

A 2.8V

L801

DRUM VS

CAM 12V CAM -6.5V

IC801

IC753

IC751

68 58

FC RST LED

60 DRUM ERROR

DRUM ERROR

TRV11/ TRV11E

(4-29)

IC802

66 CAP ERROR

(4-29)

CAP ERROR

64

62

L201

ZM RST LED

16

CAMERA CONTROL

EEPROM

IC752

(BIRDS+) CAMERA SIGNAL PROCESS

REG

CAP_VS

IC701 (GCAM3) S/H,AGC A/D CONV.

16M SDRAM

Q802

18

CAPSTAN MOTOR DRIVE, CAP FG AMP

Q1109 CHIME VDD

(RABI)

EVF 13.3V

CAP VS

LANC/DIGITAL I/O

(4-89)

(4-52)

TRV11/TRV11E

RP 4.6V

41

(4-36)

EXCEPT AEP/UK MODEL

REMOTE COMMANDER RECEIVER

PITCH,YAW SENSOR

IC3051

40 A 4.6V

SE-94 BOARD

AU 2.8V 9

49

R052

22 MF VCC

12 12

MANUAL FOCUS AENSOR

4

47 FB501

PH081,082

CN2051

21

VTR UNREG

22 22

(4-59)

R051

IR LED

CN3001

DRUM VS

52 54 51

DRUM MOTOR DRIVE DRUM FG,PG AMP LOADING MOTOR DRIVE REEL FG AMP TAPE TOP,END DET DRUM,CAP ERROR AMP

D 2.8V

R424

MT 4.75V

36

21

(4-32)

MF LED

(4-31)

(4-32)

SENSOR VCC

VTR UNREG

15

18

4PIN CONNECTOR

19

T REEL, S REEL SENSOR

13

TAPE LED

Q402

XREEL HALL ON

A 2.8V

105

MECHA CONTROL

EEPROM

CHIME PWR CONT

D 1.9V

TAPE LED A

(4-25)

CN006

J MECHA DECK

34

(SEE PAGE 4-55)

(4-25) A 3.1V

RP 4.6V

A 4.6V

42 MT 4.75V

L102

L203

IC702

A 2.8V

FB101

D 2.8V

D 1.9V

FB201

IC201 SHUTTER DRIVE

IC202 IC203

IC204 FOCUS/ZOOM MOTOR DRIVE

IRIS DRIVE IRIS HALL AMP

FP-219

TIMING GENERATOR

IC102

IC101 (TRF)

REC/PB AMP

EQ, A/D CONV. PLL

(4-38)

(4-13) CAM 12V

(TRW)

(FLEXIBLE)

IC3000

21 21

CAM -6.5V 8

(4-37)

CCD IMAGER

8

TRV11/TRV11E

IC1403

IC1405

IC1407

RS232C I/F

16Mbit SDRAM

4Mbit FLASH

IC1406

IC1404

FC RST LED LENS ASSY

D 1.5V

(4-43)

(4-45)

(SHIORI) DIGITAL STILL PROCESS

(4-45)

DIGITAL STILL CONTROL

(4-46)

(4-44)

33

MS VCC ON

Q204 CN3000 D 2.8V

16

FOCUS RESET SENSOR

8

ZOOM RESET SENSOR

FC SENS VCC 33 33

ZM RST LED Q203

Q1406,1407

D 3.1V

ZM SENS VCC 41 41 CN3001

16

CN701

3-13

3-14

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

3-8. POWER BLOCK DIAGRAM (2/2) (DCR-TRV20/TRV20E) VC-240 BOARD(2/2)

CN008 38

SHOE UNREG 8

IC1104

37

(4-62)

INTELLIGENT ACCESSORY SHOE

HI CONTROL MS VCC 28 SHOE ON BATT SIG INIT CHARGE ON VTR DD ON CAM DD ON FAST CHARGE BATT XEXT SW BATT UNREG

27 73 69 65

IC1102

(4-61)

67

91

ACV SENS

SHOE ON

75

IC1101

D1103

76

49

IB SI

48

5

7

IC1103

55

BATTER IN DETECT

REG

6

31 42 51 63 87

4

61

VDD

(4-61)

70 UNREG

1

POWER

MT 4.75V

VTR DD ON

29 28

FAST CHARGE

50

4

12

CONTROL SWITCH BLOCK(FK-30150)

RV51 D 2.8V

7

ZOOM VR

(SEE PAGE 4-91)

BATT/XEXT

66

XVTR MODE SW

14

3

4

XCAM+STBY SW

15

1

2

XPHOTO STBY SW

20

5

1

CN064

BATT IN

8

LANC I/O 72

D62-70 15

25

CAM DD ON

XRESET

38

D1102

54

BATT SIG I/F

KEY ILLUMINATION LED

3

3

MEMORY STICK

1 CN062

Q1104

17

RESET

REG

2

53

VTR UNREG

IB SO

INIT CHARGE ON 71

81

(4-61)

D1104

MT 4.75V

90

BATT SENS

VCR OFF CAMERA

14

LANC DC

VCC

POWER

XLANC ON MEMORY

Q1106

74

CONTROL SWITCH BLOCK (PS-30150)

S1

(SEE PAGE 4-91)

8

D 2.8V

CHIME PWR CONT

92

CK-92/94 BOARD

7

VTR DD SENS CN003

Note : CK-92 BOARD : TRV20 CK-94 BOARD : TRV20E PD-123 BOARD : TRV20 PD-124 BOARD : TRV20E

S100-106 D 2.8V

SHOE UNREG

7

40 12

30

SHOE UNREG 31 21

P UNREG

50

78

PANEL 2.8V PANEL -15.3V PANEL 13.3V PANEL 4.6V

2

CONTROL SWITCH BLOCK(CF-30150)

BT3201 LITHIUM BATTERY

(SEE PAGE 4-83)

VTR UNREG

21

PANEL 4.6V 8

38 14

25

PANEL 2.8V Q1011

26

REG

5

32 20

LANC DC

PANEL -15.3V 7

36 16

28

TO POWER BLOCK DIAGRAM (1/2) (PD-123/124)

PANEL 13.3V 6

34 18 EVF 13.3V

SW CN100

RESET

BTT LI 3V

80

7

CN3203

S3218

31

25 27

EVF 13.3V

19

P UNREG 12

24 28

CN3202

43 AU 4.6V

(XYZ) AUDIO I/O

AUDIO ADC&DAC

EVER 3.0V 5

5

47 CN3201

CN3205

46

(4-64) D 1.9V

(4-64)

IC502

50

IC501

52 A 2.8V

45

(4-60)

A 2.8V

105

XREEL HALL ON

D2071,2072

JK-188 BOARD 21 21 22 22

(4-59)

5

21

VTR UNREG

PH081,082

CN2051

R051

IR LED

CN3001

CN001

MECHA CONTROL

EEPROM

(4-105)

22

MANUAL FOCUS AENSOR

4 R052

SE-94 BOARD

47 AU 2.8V D 2.8V

12 12 AU 2.8V 9

9

9 A 4.6V

49

D 2.8V

MIC AMP

13 13

13 LANC DC

51 D 1.5V

12

AU 2.8V

48

IC2002

MF VCC

FB501

28 28

(4-106)

27

54

CN2071

56

59 59

EVER 3.0V

IC2091

A 2.8V

60 60

IC903 D 3.1V

IC1301

IC301

IC361

(ALIGN)

(TAKO)

(CAIN)

(LIP)

A/D CONV.

VIDEO LINE IN/OUT AMP

DV SIGNAL PROCESS

DV INTERFACE

38

IC302 CHARACTER GENERATER

IC1901

IC3051

IR TRANSMITTER

REMOTE COMMANDER RECEIVER

PITCH,YAW SENSOR

J2002 SE3501,3502

PITCH,YAW SENSOR AMP

LANC/DIGITAL I/O

MA-385 BOARD

(4-89)

40 A 4.6V

RP 4.6V

44

A 4.6V

46

D 3.1V

(4-48)

(4-50)

(4-33)

(4-36)

(4-36)

(4-52) (4-55)

RP 4.6V

41

MT 4.75V

(4-56)

D 1.9V D 2.8V

IC401

IC402

A 2.8V EVF 13.3V L801

CAP VS

IC803

66 CAP ERROR DRUM VS

CAM 15V CAM -7.5V

DRUM ERROR

(4-21)

CAP ERROR

IC802

IC801

IC752

EEPROM

2.4V REG

IC751

68

2.4V

58

EVR

CAMERA CONTROL

60 DRUM ERROR

(4-21)

64

62

(4-22) 36

(4-24)

MF LED

21

(CARILLON) CAMERA SIGNAL PROCESS RC PROCESS

IC702

CAP_VS

IC701 A/D CONV.

16M SDRAM

18

CAPSTAN MOTOR DRIVE, CAP FG AMP

DRUM VS

52 54 51

CHIME VDD

DRUM MOTOR DRIVE DRUM FG,PG AMP LOADING MOTOR DRIVE REEL FG AMP TAPE TOP,END DET DRUM,CAP ERROR AMP

SENSOR VCC

VTR UNREG

(4-17)

18

4PIN CONNECTOR

19

T REEL, S REEL SENSOR

13

TAPE LED

Q402

D 2.8V

Q801

R424

MT 4.75V

(4-23)

Q1109

(RABI)

XREEL HALL ON

(SEE PAGE 3-12)

44

IC1002

CHIME PWR CONT

TO POWER BLOCK DIAGRAM (1/2) (DD-137)

IC1001

(4-17)

TAPE LED A CN006

J MECHA DECK

34

(SEE PAGE 4-55) A 3.1V

RP 4.6V

A 3.1V

42

MT 4.75V

A 2.8V

L203

D 2.8V FB201

CD-252 BOARD

D 1.9V

L102

A 2.8V

FB101

IC204 FOCUS/ZOOM MOTOR CONTROL

(4-19)

IC1403 RS232C I/F

IC201

IC202 IC203

IC205

FOCUS/ZOOM MOTOR DRIVE SHUTTER DRIVE ND FILTER DRIVE

(4-19)

IC1404 64M SDRAM

CAM DD ON

ND FILTER PRE DRIVE, ND HALL AMP

IC102

IC1407 JPEG

(4-19)

IC1408 16M DRAM FAST PAGE

(4-39)

(4-41)

(4-40)

(4-40)

5

CCD IMAGER (4-11)

IC103

DIGITAL STILL CONTROL FB1401

IC1411 118

SHUTTER SOUND

(4-39)

(4-40)

IC104

(4-18)

IC703

LENS ASSY 10 10

(4-11)

A 2.8V

12 12 3.3V REG

D 3.3V

3

(4-11) MR VCC

3-15

F MR VCC 7 Z MR VCC 18

L151 CN701

FOCUS MR

CN151

11 11

49 49 FB1406

TIMING GENERATOR

CDS,AGC

MEMORY STICK I/F

(4-42)

IC102

AMP

IC1409 IC1410

D 3.1V

16

IC101

Q1404,1405

IC1412

EEPROM

Q103,104

(4-11)

(4-37)

IC1406

(4-40)

8

5

CAM -7V

2 D 2.8V

8

CAM 15V

EQ, A/D CONV. PLL

(4-38)

7

MS VCC ON

(TRF)

REC/PB AMP

IRIS DRIVE IRIS HALL AMP

(4-20)

IC101

(TRW)

7

CN101

3-16E

ZOOM MR

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM-1 11

12

13

14

15

16

17

CD-252 BOARD

CCD IMAGER

C NIGHT SHOT OFF

37

GND

39

F MR A

41

GND

43

IRIS DRIVE-

45

IR SW OUT

38

F MR B

40

TEMP OUT

42

IRIS DRIVE+

44

IRIS BIAS+

IRIS BIAS-

46

47

IRIS HALL+

IRIS HALL-

48

49

MR VCC

Z MR A

50

51

TEMP/MR GND

Z MR B

52

53

ND BIAS+

GND

54

55

ND HALL-

ND BIAS-

56

57

ND HALL+

GND

58

59

ND DRIVE+

ND DRIVE-

60

ZOOM-

ZOOM+

FOCUS+

FOCUS-

IR_SW_OUT

FP-219 FLEXIBLE BOARD

CCD IMAGER

50P

1

V3

V2

2

3

V4

V1

4

5

VSHT

V_DRAIN

6

7

HDR_GND

-6.5V

8

9

H2

HDR_GND

10

11

H1

HDR_GND

12

13

RG

HDR_GND

14

15

CCD_GND

CCD_GND

16

17

CCD_OUT

CCD_GND

18

19

CCD_GND

CCD_GND

20

21

12V

CCD_GND

22

OFF

23

S_GND

S_GND

24

25

ZM_XA

ZM_XB

26

27

ZM_A

ZM_B

28

VC-240 BOARD VC-241 BOARD

24P

5

4

3

29

Gnd

NightShot_Vcc

30

31

FC_SENS_OUT

THERMO_OUT

32

33

FC_SENS_Vcc

Gnd

34

35

FC_XA

FC_XB

36

37

FC_A

FC_B

38

39

ZM_SENS_OUT

Gnd

40

41

ZM_SENS_Vcc

HALL(+)

42

43

BIAS(+)

HALL(-)

44

45

BIAS(-)

Gnd

46

47

Gnd

DRIVE(-)

48

49

DRIVE(+)

SLOW SHUT

50

CN701 50P

1/24 CH BLOCK

13/24 MS-2 BLOCK 14/24 MS-1 15/24 MS-2 16/24 IN BLOCK 17/24 IO BLOCK 18/24 IR BLOCK

4/24 CA BLOCK 5/24 CH BLOCK 6/24 LD BLOCK 7/24 CM BLOCK

2

S VIDEO

AU_GND

2

AU_GND

4

5

SHOE_MIC_L

7

EXT_MIC_JACK

9

AU_2.8V

XMIC_MONO

J2002

8

MF_B

10

MF_LED

12

F_TALLY_LED

14

CN101

10P

CN005

10P

4

3

2 XOSD_SCK

1

5

XCS_LCD_DRIVER

OSD_SO

6

16

LCD_COM/XDATA

17

7

18

C-SYNC/XHD

EVER_3.0V

19

XVD

8

20

REG_GND

REG_GND

21

REG_GND

9

22

REG_GND

PANEL_B

23

31

HI_SO

32

CN007

16

EVF_RGT

18

19

EVF_13.3V

EVF_DCG/CLR

20

21

EVF_2.8V

EVF_BL-

22

23

PANEL_2.8V

EVF_BL+

24

25

PANEL_-15.3V

PANEL_13.3V

26

27

SHOE_ON

PANEL_4.6V

28

29

SHOE_GND

SHOE_UNEREG

30

31

SHOE_GND

SHOE_UNEREG

32

33

REG_GND

CAM_-7.5V

34

35

REG_GND

CAM_15V

36

37

REG_GND

D_3.1V

38

39

REG_GND

D_3.1V

40

41

RP_4.6V

A_3.1V

42

43

AU_4.6V

A_4.6V

44

45

A_2.8V

A_4.6V

46

47

A_2.8V

AU_2.8V

48

49

D_2.8V

D_1.9V

50

51

D_2.8V

D_1.9V

52

53

MT_4.75V

D_1.5V

54

55

MT_4.75V

D_1.5V

56

57

MT_4.75V

DRUM_VS

58

59

MT_GND

DRUM_VS

60

61

MT_GND

DRUM_ERROR

62

63

MT_GND

CAP_VS

64

65

VTR_DD_ON

CAP_VS

66

67

CAM_DD_ON

CAP_ERROR

68

69

INIT_CHARGE_ON

VTR_UNREG

70

71

FAST_CHARGE

VTR_UNREG

72

73

BATT_SIG

VTR_UNREG

74

75

BATT_XEXT_SW

BATT_UNREG

76

77

P_UNREG_GND

P_UNREG

78

79

P_UNREG_GND

P_UNREG

80

B TO(2/2)

XX

XDS_FLASH CAM_XRESET CAM_RXD CAM_TXD CAM_TEST_A XCS_MC_FLASH XDRP_SCK DRP_SO DRP_SI MC_F_BUSY REG_GND HI_XRESET HI_RXD HI_TXD HI_TEST_A

27P

17

18

19

20

21

22

23

24

25

26

27

17

18

19

20

21

22

23

24

25

26

27

CAP_U

CAP_U

CAP_U

CAP_U

N.C.

FG1

FG_VCC

FG_VCC

FG2

FG_GND

FG_GND

FG_GND

16 16 VHE-

FG_GND

15 15 WHE-

FG2

14 14 CAP_W

FG_VCC

13 13 CAP_W

FG_VCC

12 12 CAP_W

FG1

11 11 CAP_W

N.C.

HE_GND 10 10 HE_GND

CAP_U

WHE+ 9 9 WHE+

CAP_U

VHE+ 8 8 VHE+

CAP_U

UHE+ 7 7 UHE+

CAP_U

HE VCC 6 6 HE VCC

VHE-

UHE5 5 UHE-

WHE-

CAP_V 4 4 CAP_V

CAP_W

CAP_V 3 3 CAP_V

CAP_W

CAP_V 2 2 CAP_V

CAP_V 1 1 CAP_V

TAPE_TOP 27 27 TAPE_TOP

TOP/END_GND 26 26 TOP/END_GND

TAPE_END 25 25 TAPE_END

SREEL+ 24 24 SREEL+

SREEL23 23 SREEL-

HALL_GND 22 22 HALL_GND

TREEL21 21 TREEL-

TREEL+ 20 20 TREEL+

HALL_VCC 19 19 HALL_VCC

CHIME_VDD 18 18 CHIME_VDD

CHIME_SDA 17 17 CHIME_SDA

CHIME_SCK 16 16 CHIME_SCK

XREC_PROOF 15 15 XREC_PROOF

MIC/REC_SW_GND 14 14 MIC/REC_SW_GND

TAPE_LED_A 13 13 TAPE_LED_A

TAPE_LED_K 12 12 TAPE_LED_K

XCCDOWN_SW 11 XCCDOWN_SW 11

SW_COM/SW_GND 10 10 SW_COM/SW_GND

MODE_SW_C 9 9 MODE_SW_C

MODE_SW_B 8 8 MODE_SW_B

MODE_SW_A 7 7 MODE_SW_A

DEW6 6 DEW-

DEW+ 5 5 DEW+

LM_UNLOAD 4 4 LM_UNLOAD

LM_UNLOAD 3 3 LM_UNLOAD

LM_LOAD 2 2 LM_LOAD

LM_LOAD 1 1 LM_LOAD

DRUM_W 10 DRUM_W 10

DRUM_W 9 9 DRUM_W

DRUM_V 8 8 DRUM_V

DRUM_V 7 7 DRUM_V

DRUM_U

58

6

YS_OUT

6

PS_OUT

DRUM_U

57

DRUM_U

56

5

54

C_RESET

5

52

REG_GND

REG_GND

DRUM_U

AV_GND

REG_GND

55

M COM

VIDEO_I/O

53

4

51

4

50

M COM

R_IO

FG/PG COM

L_IO

3

48

49

3

AV_JACK_IN

FG

XHP_JACK_IN

2

46

47

2

HP_L

FG

HP_R

PG

44

45

1

DV_GND

1

DV_GND

PG

42

43

GND

TPA

10

TPB

10

40

41

GND

NTPA

XEVEN

NTPB

9

38

39

9

DV_GND

XEVEN

DV_GND

YEVEN

36

37

8

XSJACK_IN

8

S_Y_OUT

YEVEN

34

35

GND

S_Y_GND

7

32

REG_GND

7

S_C_OUT

33

GND

30

31

S_C_GND

XODD

KEY_AD2

6

REG_GND

6

28

29

XODD

LANC_DC

YODD

REG_GND

5

26

27

5

24

LANC_SIG/232C_RD

YODD

22

REG_GND

GND

25

20

XLANC_JACK_IN

4

LANC_GND/232C_TD

4

23

18

VTR_UNREG

GND

VTR_UNREG

XSDL

21

16

REG_GND

YSDL

IR_DRV_CL

GND

19

REG_GND IR_DRV_EM

3

REG_GND

2

SIRCS_SIG

17

1

A_4.6v

15

LM_UNLOAD

LM_UNLOAD

DEW+

DEW-

MODE_SW_A

MODE_SW_B

MODE_SW_C

SW_COM/SW_GND

4

5

6

7

8

9

10

A_2.8V

A_2.8V CN3001

3

59

FG/PG COM

M901 FG PG VIDEO HEAD

60

60P

M DRUM MOTOR

LM_LOAD

INFINITY

2

MAN

TRV6 MODEL:DCR-TRV6 TRV6E MODEL:DCR-TRV6E TRV11 MODEL:DCR-TRV11 TRV11E MODEL:DCR-TRV11E TRV20 MODEL:DCR-TRV20 TRV20E MODEL:DCR-TRV20E

S901 CN901 3P

LM_LOAD

AUTO

CN2001

(CC DOWN)

M902

REC PROOF HALL

Q902

Q901

TAPE TOP

TAPE END

M

FG

CAPSTAM MOTOR

D901

4P

1

INT MIC L

2

INT MIC GND

3

INT MIC R

4

INT MIC GND

1

MF_A

2

MF_B

IC2091

3

GND

R

4

MF_LED_A

5

MF_LED_B

TAPE LED

M903

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

1 MIC_R

AU_GND

MIC_L

AU_GND

SHOE_MIC_L

XMIC_MONO

EXT_MIC_DET

ZOOM_MIC_CONT

AU_2.8V

MF_B

MF_A

MF_LED

A_4.6v

XF_TALLY_LED

XSIRCS_IN

GND

GND

20 GND

IR_EM

IR_DRV

21 VTR_UNREG

22 VTR_UNREG

23 GND

24 232C_TD

25 LANC_JACK_IN

26

27

CN2071

REMOTE COMMANDER RECEIVER

28P

5P

LANC_SIG

KEY_AD2

MIC

LANC_DC

28

MIC

CN2051

MANUAL FOCUS SENSOR

27P

3

13

1

J2001

LASER LINK

SE-94 BOARD

CN006

2

MF_A

FOCUS

N

14

EVF_HST

EVF_PWM

6

ZOOM_MIC_CONT

S903 S2061

MIC (R)

EVF_HCK2

EVF_LED_K

17

MT_4.75V

7

1

MA-385 BOARD

DIGITAL I/O

MIC (L)

EVF_DET

15

CN001 60P

J3002

MIC901 MIC UNIT

13

J3004

K

M

24

33

XRESET_SW

CN004

GND

DV IN/OUT

MIC

XHI_SCK

34

PANEL_2.8V

22/24 HI BLOCK 23/24 AU BLOCK 24/24 CN BLOCK

XSDL

J3003

AUDIO/VIDEO

PLUG IN POWER

12

RF_MON

20

YSDL

J

L

EVF_HCK1

J3001 11

LANC

EVF_VCC

GND

19

16

MIC_R

11

6

RF_IN/LANC_JACK_IN

18

15

MIC_L

10

SWP

13

3

EVF_BLK

GND

12

1

EVF_GND

JIG_TDO

11

JK-188 BOARD

8

9

JIG_TDI

14

I

EVF_B

TCK

17

TRV6/6E/11/11E MODEL

EVF_VST

TMS

10

1

CPC

21/24 MC BLOCK

10/24 JC-2 BLOCK 11/24 RF BLOCK 12/24 MS-1 BLOCK

7

PANEL_COM

16

19/24 VF BLOCK 20/24 MD BLOCK

8/24 CA BLOCK 9/24 JC-1 BLOCK

4

EVF_R

EVF_EN

XHD/PSIG

8

DRIVE(-)

DRIVE(+)

Gnd

HALL(-)

BIAS(-)

BIAS(+)

ZM_SENS_Vcc

ZM_SENS_OUT

Gnd

FC_B

FC_A

FC_XB

FC_XA

Gnd

FC_SENS_Vcc

THERMO_OUT

FC_SENS_OUT

Gnd

NightShot_Vcc

ZM_B

ZM_A

CN3000

ZM_XB

ZM_XA

HALL(+) 6

25

H_START

9

7

8

XCS_LCD

PD_VCO

9

6

9

26

PANEL_VG

8

5

24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

P_UNREG

7

14

2/24 LD BLOCK 3/24 CM BLOCK

EVF_G

EVF_VCK2

GND

13

(TRV6/6E/11/11E MODEL)

2

EVF_STB

5 EVF_VCO

12

(TRV20/20E MODEL)

EVF_COM

3

1

EVF_VG

4

SUPER NIGHT SHOT

CN002 80P

TRV20/20E MODEL

3

H

27

EFN_BL-

2

NIGHT SHOT ON

P_UNREG

3

1

G

28

EVF_BL+

15

LENS UNIT

XHD_OUT

LANC_SIG

2

11

CN101

20P

1

10

F

29

35

KEY_AD7

30

36

PANEL_13.3V

51P

6

E

10

36

REG_GND

FOCUS+

11

FOCUS-

PANEL_G

34

35

12

ZOOM+

CN003

39P

FLEXIBLE

REG_GND

ZOOM-

21

13

32

33

37

1

GND

KEY_AD6

2

S.N.SHOT

38

3

XCAM_STBY_SW

30

31

PANEL_-15.3V

4

N.C.

FRQ

39

5

XVTR_MODE_SW

GND

KEY_AD5

6

XS/S_SW

28

29

40

7

XPHOTO_STBY_SW

ZV1

PANEL_4.6V

8

GND

ZSG1

41

9

D_2.8V

26

27

KEY_AD4

10

ZOOM_AD

TG_VD

42

11

GND

TG_FLD

D_2.8V

12

XPHOTO_FREEZE

24

25

43

13

MS_LED_VCC

22

TG_ID

KEY_AD3

14

XMS_ACCSEE

20

CAM_SI

TG_HD

44

15

GND

CAM_SCK

GND

23

REG_GND

16

KEY_AD_1

CSUB

21

45

17

MT_4.75V

19

CN008

REG_GND

18

FK_LED_ON

18

46

19

MT_4.75V

16

CAM_SO

REG_GND

20

KEY_AD_0

14

CS_CAM

GND

47

21

IR_LED_ON

XCAM_RST

MCK

17

REG_GND

22

IR_LED_VCC

GND

15

48

23

XEJECT_SW

13

SP+

24

GND

12

49

25

SCLK

A_2.8V

REG_GND

26

DIO

D_3.3V

50

27

GND

11

SP-

28

BS

10

51

29

MS_IN

8

A_2.8V

DIAL_B

30

MS_VCC

CAM_15V

PBLK

DIAL_A

31

SHOE_GND

6

CAM_DD_ON

9

BATT_LI_3V

32

SHOE_GND

GND

33

CAM_-7V

7

1

2

3

IR_SW

F_MR_VCC

F_MR_A

F_MR_B

TEMP/F_MR_GND

5

CN701 60P

5

4

5

6

7

8

TEMP

IRIS_DRIVE+

IRIS_DRIVE-

IRIS_BIAS+

IRIS_BIAS-

IRIS_HALL-

IRIS_HALL+

Z_MR_VCC

Z_MR_B

Z_MR_GND

Z_MR_A

ND_BIAS-

ND_HALL-

ND_BIAS+

ND_HALL+

4

4

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

CN051

ND_DRIVE+

ND_DRIVE26

27

D

2

CCDout (-)

CN009

27P

ON

CCDout (+)

GND

CAP_W

LENS UNIT

GND

3

SHOE_MIC_L

B

60P

1

34

CN101 SUPER NIGHT SHOT

MIC_GND

S001

35

5

SHOE_MIC_R

4

GND

36

3

GND

GND

SHO_ID2

SLOW_SHUT

GND

5

37

SLOW_SHUT

4

SHO_ID1

3

FP-179

NS-10 BOARD 38

2

LANC_SIG

1

GND

39

GND

GND

N.C.

GND

2

SHOE_UNREG

1

20

A TO(2/2)

PSIG

5P

SHOE_UNREG

CN052

19

PANEL_R

C TO(2/2)

A

18

14

10

REG_GND

9

15

8

PANEL_VG

7

REG_GND

6

PANEL_COM

5

P_UNREG_GND

4

P_UNREG_GND

3

CAP_W

2

P_UNREG_GND

1

M LOADING MOTOR

S902 MODE SWITCH

DEW SENSOR

FP-100

FP-228

FLEXIBLE

FLEXIBLE

FP-102 FLEXIBLE

J-100 MECHANISM

16

4-1

4-2

FRAME SCHEMATIC DIAGRAM (1/2)

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

FRAME SCHEMATIC DIAGRAM-2 2

1

3

5

4

6

7

8

9

10

11

12

14

13

LCD902 CHARACTER DISPLAY

3

DIAL_B

13

2

DISP_VD

P_UNREG

12

3

GND

S3201 5

REG_GND

6

SP+

7

REG_GND

XCS_LCD_DAC

11

XHI_SCK

10

PC-119

5

PANEL_2.8V

HI_SO

9

HARNESS

6

PANEL_13.3V

8

7

PANEL_-15.3V

9

REG_GND

10

REG_GND

11

KEY_AD3

S3203

8

PANEL_4.6V

6

9

HI_SO

5

10

XHI_SCK

4

11

XCS_LCD_DAC

GND

3

12

P_UNREG

DISP_VD

2

13

P_UNREG_GND

PANEL_-15.3V

7

PANEL_13.3V PANEL_2.8V GND

MEMORY INDEX

5 24P

4

N.C.

5

BL_LOW

3

GRES

6

LED

2

GPCK

7

BL_GND

1

9

12

13

14

15

16

17

18

19

20

21

SEG10

SEG11

SEG12

SEG13

SEG14

SEG15

SEG16

COM3

COM4

N.C.

8

11

7

SEG9

6

SEG6

10

5

SEG5

SEG8

4

SEG4

KEY_AD6

1/2 LCD/CN BLOCK

RESET

10

18

PANEL_13.3V

2/2 RGB/TG BLOCK

VCOM

11

19

KEY_AD7

VBC

12

20

PANEL_2.8V

STBYB

13

21

XRESET_SW

SRT

14

22

P_UNREG_GND

OE

15

23

P_UNREG_GND

CLR

16

24

P_UNREG_GND

MCLK

17

25

PSIG

HCNT

18

26

XHD_OUT

VR

19

27

P_UNREG

VG

20

28

P_UNREG

VB

21

29

XCS_LCD

VSS

22

30

XHI_SCK

VDD

23

31

HI_SO

VSH

24

32

REG_GND

33

REG_GND

CN2176

PANEL_COM

MEMORY+

10

PANEL_VG

9

PANEL_R

S3207

8

PANEL_G

DIGITAL EFFECT

7 8 9 10 11

2

OSD_SO

12

1

12P

OSD_SO XOSD_SCK XCS_LCD_DRIVER LCD_COM/XDATA EVER_3.0V PANEL_B PANEL_G PANEL_R PANEL_VG PANEL_COM XHD_OUT PSIG

S3215 MEMORY DELETE

TITLE REG_GND S3211 35

XVD

36

C-SYNC/XHD

37

PANEL_COM

38

REG_GND

39

PANEL_VG

40

REG_GND

S3216 MENU

END SEARCH

S3212

S3217 DISPLAY

MEMORY MIX

S3213

DD-137 BOARD

S3218

LB-64 BOARD

CONTROL SWITCH BLOCK (FK-30150)

41

PANEL_R

42

REG_GND

43

PANEL_G

44

REG_GND

45

PANEL_B

1

EVF_EN

EVF_COM

2

COM

27

1

COM

VDD

16

46

REG_GND

3

EVF_STB

EVF_G

4

G

26

2

G

VSS

15

47

EVER_3.0V

5

EVF_VCK2

EVF_R

6

R

25

3

R

VST

14

48

LCD_COM/XDATA

7

EVF_VST

EVF_B

8

B

24

4

B

VCK2

13

PB ZOOM

RESET

S3214

BT3201

CN1603

80P

CN1604

27P

CN2201

27P

CN2202

49

XCS_LCD_DRIVER

50

XOSD_SCK

S3209 MEMORY INDEX

51

OSD_SO

S3205

S3212 MEMORY PLAY

S3206

SP+

2

SP-

EVF_BLK

10

BLK

23

5

BLK

EVF_HCK1

12

HCK1

22

6

HCK1

13

EVF_DET

15

EVF_LED_K

2P

14

HCK2

21

7

HCK2

EVF_HST

16

HST

20

8

HST

17

EVF_PWM

EVF_RGT

18

RGT

19

19

EVF_13.3V

EVF_DCG/CLR

20

DCG/CLR

18

21

6P

PANEL_-15.3V

27

SHOE_ON

22

EN

17

24

STB

16

26

VCK2

15

PANEL_4.6V

28

VST

14

N.C.(XTALLY_LED)

A_2.8V

A_4.6V

46

47

A_2.8V

AU_2.8V

48

GND

EVF_BL_4.6V

44

GND

42

A_4.6V

KEY_AD4X

A_3.1V

AU_4.6V

6

RP_4.6V

43

KEY_AD4X

8

5

9

EVF_BL_4.6V

4

10

EVF_BL_GND

40

3

EVF_BL_GND

38

D_3.1V

GND

36

D_3.1V

REG_GND

GND

CAM_15V

REG_GND

39

2

REG_GND

37

1

35

D_2.8V

11

KEY_AD7

VDD

KEY_AD3

34

7

CAM_-7.5V

CTRL_B

REG_GND

6

33

CTRL_A

12

5

13

VSS

4

VSS

32

3

30

SHOE_UNEREG

GND

SHOE_UNEREG

SHOE_GND

GND

SHOE_GND

31

45

9 10

RGT DCG/CLR

11

EN

12

STB

13

VCK2

14

VST

EVF_BL_GND EVF_BL_GND EVF_BL_4.6V

7

21

EVF_BL_4.6V

6

22

N.C.(XTALLY_LED)

DET

5

23

DET

LED_K

4

24

LED_K

25

PWM

26

N.C.

1

27

N.C.

55

MT_4.9V

D_1.5V

56

FLEXIBLE

57

MT_4.9V

DRUM_VS

58

S97

59

MT_GND

DRUM_VS

60

VTR_DD_ON

CAP_VS

66

CAM_DD_ON

CAP_ERROR

68

69

INIT_CHARGE_ON

VTR_UNREG

70

71

FAST_CHARGE

VTR_UNREG

72

BATT_SIG

75

BATT/XEXT_SW

VTR_UNREG

74

BATT_UNREG

76

S103

P_UNREG_GND

P_UNREG

78

79

P_UNREG_GND

P_UNREG

80

5

SHOE_MIC_L

2

MIC_GND

3

SHOE_MIC_R

4

XPHOTO_STBY_SW

SHO_ID2

5

6

GND

SHO_ID1

6

7

2.8V

LANC_SIG

7

SHOE_UNREG

8

S61 OPEN/EJECT

LCD

8

ZOOM_AD

9

GND

EVF

S62 10

XPHOTO_FREEZE

11

MS_LED_VCC

12

XMS_ACCSEE

STOP S71

S63 13

GND

14

KEY_AD_1

15

MT_4.75V

PHOTO REW (FREEZ)

CONTROL SWITCH BLOCK (PS-30150)

(PHOTO REC) S64

FK_LED_ON PLAY

17

MT_4.75V

18

KEY_AD_0

19

IR_LED_ON

CN64

6P POWER XPHOTO_STBY_SW

1

XCAM_STBY_SW

2

20

IR_LED_VCC

21

XEJECT_SW

GND

3

XVTR_MODE_SW

4

XS/S_SW

5

OFF(CHG) S66 22

GND

23

SCLK

24

DIO

25

GND

26

BS

27

INS

16

MEMORY S67

S2 START/STOP

28

MS_VCC

29

SHOE_GND

30

SHOE_GND

EDITSEARCHLINE IN/OUT MODEL

TO(1/2)

1

ACV_GND

2

BATT_XEXT

3

31 J902 DC IN

SHOE_MIC_L

CN62

CN52

FRAME SCHEMATIC DIAGRAM (2/2)

32

MIC_GND

33

SHOE_MIC_R

34

SHO_ID2

35

SHO_ID1

VSS

1

2

BS

SCLK

2

3

VCC

4

DIO

5

36

LANC_SIG

N.C

6

37

INS

7

N.C

S72

3P BATT_UNREG

1

BATT_SIG

2

BATT_GND

3

J901 BATTERY TERMINAL

INS

3

DIO

4

BS

5

SHOE_UNREG

VSS

6

38

SHOE_UNREG

STATICS_GND

7

8

SCLK

39

N.C.

N.C.

8

9

VCC

10

VSS

S106

4-3

1 VCC

8P

10P

REC

SUPER LASER LINK

LCD BRIGHT+

VOLUME-

CAMERA

6

MEMORY MODEL S104

M

VCR

FF

S105 VOLUME+

S1

S65

S69,70

CN1602 77

XS/S_SW

LCD903

C 3P

S100 73

XVTR_MODE_SW

4

1

EDITSEARCH+

TO(1/2)

PROGRAM AE

N.C.

3

SHOE_GND

S68

ACV_UNREG

67

2

8P

PAUSE

2

65

3

20

3

B

R

19

N.C.

SEL/PUSH EXEC

4

18

N.C.

64

XCAM_STBY_SW

16

PWM

CAP_VS

5

B

VDD

54

MT_GND

6

BLK

17

52

63

HCK1

1

50

62

7

2

D_1.5V

DRUM_ERROR

8

G

D_1.9V

MT_GND

HST HCK2

COM

D_1.9V

61

9

CN63

39P

1

10

VSS

D_2.8V

FP-181

DCG/CLR

VSS

MT_4.9V

S102

EXPOSURE

11

16

D_2.8V

(PANEL REV)

S101

12

EN

15

53

CN1601

L

STB

RGT

51

49

K

EVF_BLEVF_BL+ PANEL_13.3V

29

2

CN3204

PANEL_2.8V

25

41

CONTROL SWITCH BLOCK (CF-30150)

EVF_2.8V

23

1

CN3203

EVF_HCK2

MEMORY DELETE

MEMORY MODEL

J

EVF_GND EVF_VCC

S3215

7P

1

MEMORY MIX

MEMORY+

CN3206 SP901 SPEAKER

I

9 11

MEMORY –

FLEXIBLE

H

CN003

FP-180

S3203

INTELLGENT ACCESSORY SHOE

16P

DATA CODE

LCD BRIGHT-

4-4

MEMORY STICK CONNECTOR

34

6

3

XOSD_SCK

S3210

5

4

XCS_LCD_DRIVER

MEMORY –

HARNESS

5

LCD_COM/XDATA

S3209

4

6

EVER_3.0V SELFTIMER

PC-118

7

PANEL_B S3208

3

LCD

P_UNREG_GND

12P

2

6 5

17

11

N.C.

LCD901

N.C.

9

XHD_OUT

7

N.C.

STBYB

S3206

8

N.C.

4

PANEL_-15.3V

1

9

N.C.

3

16

12

10

N.C.

2

8

CN3201

N.C.

VDD

GSRT

14

BACK-LIGHT

11

VGL

KEY_AD5

1

NR901

12

N.C.

VSS

15

DISP_HD

13

N.C.

1

PANEL_4.6V

(TRV6/6E/20E MODEL)

14

N.C.

VGH

KEY_AD4

PSIG

G

P_UNREG

D_2.8V

MEMORY PLAY

F

4

14

S3205

E

P_UNREG_GND

13

BACK LIGHT

A TO(1/2)

(TRV11/11E/20 MODEL)

PD-123 BOARD PD-124 BOARD

3

12

S3204

D

SEG7

3

SEG3

REG_GND FADER

2

BL_DET

CN2101

15

N.C.

FLEXIBLE

8

GND

PANEL_4.6V

(PANEL CLOSE)

S3202

4

1

PANEL_4.6V

SP-

BL_HI 5P

LCD_PWM

FP-183

4

P_UNREG_GND

15P CN2174

21P

BATT_LI_3V

DISP_HD

INVERTER UNIT

FP-179 FLEXIBLE

C

2

1

2

CN2173 14P 14

SEG2

14P P_UNREG_GND

1

CN3202

SEG1

51P

DIAL_A

MEMORY MODEL : DCR-TRV11/TRV11E/TRV20/TRV20E TRV6 MODEL : DCR-TRV6 TRV6E MODEL : DCR-TRV6E TRV11 MODEL : DCR-TRV11 TRV11E MODEL : DCR-TRV11E TRV20 MDEL : DCR-TRV20 TRV20E MODEL : DCR-TRV20E

FLEXIBLE

CN2175

1

(TRV6/6E/20E MODEL)

COM2

CN3205

B

FP-182

(TRV11/11E/20 MODEL)

COM1

CK-92 BOARD CK-94 BOARD

18

17

LINE IN/OUT MODEL : DCR-TRV6/TRV6E:E,HK,AUS,CN,JE/ TRV11/TRV11E:E,HK,AUS,CN,JE/ TRV20/TRV20E

LCD

A

16

15

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

NS-10 (SUPER NIGHTSHOT SW) PRINTED WIRING BOARD

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

— Ref. No. NS-10 Board; 4,000 Series —

THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (Measuring conditions voltage and waveform)

(For printed wiring boards) • b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) • Through hole is omitted. • Circled numbers refer to waveforms. • There are few cases that the part printed on diagram isn’t mounted in this model. • Chip parts. Transistor Diode C

B

E

65 4

45 6

4

12 3

32 1

32 1

5

1

3

2

54 3

2

3

1

2

• Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. * (VOM of DC 10 MΩ input impedance is used.). • Voltage values change depending upon input impedance of VOM used.) * 1. Connection

3

1

2

Pattern Box

1

(For schematic diagrams) • All capacitors are in mF unless otherwise noted. pF : m mF. 50V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10W unless otherwise noted. kW=1000W, MW=1000kW. • Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520

1.5m

Front of the lens

1-677-555-

Kinds of capacitor Temperature characteristics External dimensions (mm) 2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.

Yellow

White Magenta Red Blue

A=B

For printed wiring board • Refer to page 4-125 for parts location. • This board is four-layer print board. H5owever, the patterns of layers two to four have not been included in the diagram.

B A

LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)

There are few cases that the part printed on this diagram isn’t mounted in this model.

DD-137 (DC/DC CONVERTER)

Fig. a (Video output terminal output waveform) JK-188 (AV IN/OUT)

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

Yellow Cyan Green White Magenta Red Blue

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

A B

H

Cyan Green

• Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2 : non flammable resistor • 1 : fusible resistor • C : panel designation • A : B+ Line * • B : B– Line * •J : IN/OUT direction of (+,–) B LINE. * • C : adjustment for repair. * • Circled numbers refer to waveforms. * * Indicated by the color red.

INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)

Electron beam scanned frame CRT picture frame

Fig.b (Picture on monitor TV) When indicating parts by reference number, pleas include the board name.

4-5

4-6

SUPER NIGHTSHOT SW NS-10

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

CD-252 (CCD IMAGER) PRINTED WIRING BOARD — Ref. No. CD-252 Board; 4,000 Series —

For printed wiring board • Refer to page 4-125 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram. • Chip parts Transistor C

B

E

There are few cases that the part printed on this diagram isn’t mounted in this model. LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER) DD-137 (DC/DC CONVERTER)

JK-188 (AV IN/OUT)

1-677-549-

INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)

CCD IMAGER CD-252

4-7

4-8

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

1-677-549-

4-9

4-10

CCD IMAGER CD-252

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E For Schematic Diagram • Refer to page 4-7 for CD-252 printed wiring board. • Refer to page 4-6 for NS-10 printed wiring board. • Refer to page 4-113 for waveforms.

R108

C128 0.1u B

GND R1.7/P0 SHD R1.7/P0 SHP

GND R2.6/P0 CLPDM

CCDout (+)

2

3

GND

CCDout (-)

4

5

CAM_-7V

GND

6

7

CAM_DD_ON

CAM_15V

8

9

PBLK

A_2.8V

10

11

D_3.3V

A_2.8V

12

13

GND

XCAM_RST

14

15

MCK

CS_CAM

16

17

GND

CAM_SO

18

19

CSUB

CAM_SCK

20

21

GND

CAM_SI

22

0.1u B

4

23

TG_HD

TG_ID

24

25

TG_FLD

TG_VD

26

27

ZSG1

ZV1

28

29

GND

FRQ

30

31

S.N.SHOT

GND

32

5

CAM_DD_ON

CCDPBLK

IC104

TG_HD TG_FLD ZSG1

SLOW_SHUT

FOCUS-

39

VM

40

V2

41

V4

42

V1

45

SHT

46 47 48

VSS1

TG_ID

CHCK

TEST

CK

VSS5

OSCO

OSCI 1.3

ID

VDD3

2.6

R1.3/P0

TGVD

TGHD

TGFLD

2.3

R2.6/P0

1.3

0.9

22

PBLK

21

NC

20

VSS4

19 18

16

VL

AVDD2

15

SSO

AVDD1

14

H2

13

33

ZOOM-

ZOOM+

34

35

FOCUS-

FOCUS+

36

37

SLOW_SHUT_GND

IR SW OUT

38

39

F MR A

F MR B

40

41

GND

TEMP OUT

42

43

IRIS DRIVE-

IRIS DRIVE+

44

45

IRIS BIAS+

IRIS_BIAS-

46

47

IRIS HALL+

IRIS HALL-

48

49

MR VCC

Z MR A

50

51

TEMP/MR GND

Z MR B

52

53

ND BIAS+

GND

54

RG

VSS2

4

5

6

7

8

9

10 11 12

CLPDM PBLK

FB104 0uH

ND_HALL55 ND_HALL+ ND_DRIVE+

C126 C127 10u 0.1u B P

ND HALL-

ND BIAS-

TRV20 MODEL :DCR-TRV20 TRV20E MODEL:DCR-TRV20E

TG_ID TG_VD ZV1

ZOOM+

ND_DRIVE-

CN151

FOCUS+

ND_HALL+

NT_SHOT

ND_BIAS+

F_MR_B

ND_HALL-

TEMP I_DRIVE+

CD-252

ND_BIAS-

ND_BIAS+

23

ND_HALL-

22

ND_BIAS-

21

Z_MR_A

20

Z_MR_GND

19

Z_MR_B

18

Z_MR_VCC

17

IRIS_HALL+

16

IRIS_HALL-

15

IRIS_BIAS-

14

IRIS_BIAS+

13

IRIS_DRIVE-

12

IRIS_DRIVE+

11

TEMP OUT

10

TEMP/F MR GND

I_BIAS-

56

57 59

GND

ND HALL+ ND DRIVE+

58

ND DRIVE-

ND_DRIVE-

LENS BLOCK

I_DRIVE-

60 I_DRIVE+

FB105 0uH

TO VC-240 BOARD CN701 TEMP

(SEE PAGE 4-18)

F_MR_B 9

F_MR_B

8

F_MR_A

7

F_MR_VCC

6

IR_SW

5

IR_SW_OUT

4

FOCUS(-)

3

FOCUS(+)

2

ZOOM+

1

ZOOM-

F_MR_A

NT_SHOT FOCUS-

NS-10 BOARD

FOCUS+

XSHD

(TRV20/20E MODEL)

ZOOM+ XSHP L151 10uH

2.6 3.4 H2

R151 XX

ZOOM-

C151 10u 6.3V P

SLOW SHUTTER SW -REF.NO.:4000 SERIESXX MARK:NO MOUNT

C152 1u B CN152

SIGNAL PATH

1

GND

2

GND

3

SLOW_SHUT

4 5

REC

Y

Y/CHROMA

CN152

S001

5P GND

1

GND

2 3

GND

GND

4

GND

GND

5

LENS BLOCK is replaced as a block, so that these PRINTED WIRING BOARD and SCHEMATIC DIAGRAM are omitted.

4-12

5P

SLOW_SHUT

VIDEO SIGNAL

H1

RG

ND_HALL+

24

I_HALL+

PB

4-11

ND_DRIVE-

25

Z_MR_B

16

CCD IMAGER

26

27P

Z_MR_A

Z_MR_A Z_MR_B

ND_DRIVE+

ND_BIAS-

I_BIASI_HALL-

27

I_BIAS+

CHROMA

I

CAM_SI

H1

VSS3

AVDD0

3

C105 0.1u B

CAM_SCK

I_HALL-

R0.9/P0

R1.3/P0

R0.4/P0

TESTEN

3.4

R2.9/P0

2.6

DSGAT

2

CAM_DD_ON

VDD1

2.6

2.3

1 CAM_SCK

H

2.4

CLPDM

XSHP

R1.7/P0

RST

C104 10u 10V A

23

XRS R1.7/P0

SEN

-7.8 CAM_SI

VDD2

17

XCAM_RST

R-7.2/P0

R2.2/P0

24

XSHD

CS_CAM

G

V3

2.6

IC102 CXD2477R-T4

C125 0.1u B

L103 10uH

L104 10uH 3.3V

TIMING GENERATOR

VH

44

C124 10u P

XCHCK

6

IC102

0.2

43 R-0.4/P0

CS_CAM CAM_SO

ND_BIAS+

R2.6/P0

2.5

R-7.0/P0

R2.6/P0

ZSG1 CSUB

R15.0/P0 V3

ZV1

38

R-7.2/P0

V1

R109 0

SSI

37 R2.4/P0

R-0.5/P0

V4

I_BIAS+

SSK

V2

ZV1

I_DRIVE-

R102 82

36 35 34 33 32 31 30 29 28 27 26 25

CAM_SO

0uH FB101

F

nor exposed to strong light. XCAM_RST

SLOW_SHUT

TG_VD

C103 3.3u 20V TA A

In addition, ensure that the receiver is not covered with dusts

ND_DRIVE+

F_MR_A

C112 0.001u B

its structure, handle it carefully like for the MOS IC.

CLPDM

AMP

FB109 0uH

• As the CCD imager may be damaged by static electrictiy from

CCD+

I_HALL+

TG_HD

ZSG1

FB102

E

TG_FLD

0uH

C110 0.001u B

17

adjustments for the camera section.

60P

GND

4

CCD_IN

GND 0.6 OUT2 0.5 OUT1 2.6 VDD

CN101 1

3

2

BYP

ZOOM-

C111 5p CH

X101 66MHz

16

• If the CCD imager has been replaced, carry out all the 1.6

AD80017JSTRL

15k

R107 470k

15

with a CCD imager. When replaching this board, remove the CCD imager from the

2

8 9

B

BYP R0.5/P0 BYP

14 13 12 11 10

B 68p

0.1u

C131

5

VCO

D101 1T379-01-T8A

14

• The CD-252 board mounted as a repair part is not equipped

7

C114

R106 5600

IC103

13

Precautions Upon Replaching CCD imager

6

2.8 OUT

12

C129 10u P

C119

IN-

0.7

11

FB106 CAM_DD_ON 0uH

1

R0/P13.4

2

VCC VSS

3

1

9.8

IN+

C130 0.1u L105 10uH B

3

R113 10k 3.3u A

V1

V2

V3

V4

XSHP

IC103 TA75S01F(TE85R) 0.7

D

XSHD FB103 0uH

Q101 UN9213J-(TX).SO SWITCH

BYP

0.4

FB108 0uH

Q104 UN9213J-(K8).SO

IC104

C118 0.1u

R123 0

1

R8.9/P0 0

2

R104 0

10

old one and mount it onto the new one.

C122 0.1u B R1.3/ P0.1

1.3

R105 4700

C

C113 0.022u B

C109 0.1u B

C116

7

9

2 R2.9/P0

3

0.1u F

6

R112 220k

VDD

RCSUB

VL 5

8

1

Q103,104 CAM DD ON SWITCH

C120

R14.9/ P0

R0/P13.7 R114 1M

5

4

C107 10u 10V A

7

15.0

4

3

C108 0.1u B 1608

R12.4/ P0 R11.7/ P0

2

C106 4.7u 25V TA B BUFFER

GND

Q102 2SC4250(T5LSONY1)

8

CCD IMAGER

1

1

H1 RG

H1

H2

GND

VSUB

9

IC101 V4

R122

B

ICX237AKF-13

0

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

14 13 12 11 10

CCD_OUT

C101 0.1u B

6 Q103 NDS356AP

R15.0/P0

V1

-REF.NO.:5000 SERIESXX MARK:NO MOUNT

V2

CCD IMAGER

5 L101 100uH

V3

(TRV20/20E MODEL)

C132 2200p B

H2

C102 0.1u B

CD-252 BOARD

4

3

3

IC101

A

2 RG

1

SUPER NIGHT SHOT

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

For Schematic Diagram • Refer to page 4-16 for printed wiring board. • Refer to page 4-113 for waveforms.

2

1

3

FP-219 FLEXIBLE BOARD CCD IMAGER

A

4

5

6

7

8

9

10

(TRV6/6E/11/11E MODEL)

R3001 0

CN3001

7

HDR_GND

9

H2

HDR_GND

10

11

H1

HDR_GND

12

13

RG

HDR_GND

14

15

CCD_GND

CCD_GND

16

17

CCD_OUT

CCD_GND

18

7

19

CCD_GND

CCD_GND

20

21

12V

CCD_GND

22

23

S_GND

S_GND

24

25

ZM_XA

ZM_XB

26

27

ZM_A

ZM_B

28

29

GND

NightShot_Vcc

30

31

FC_SENS_OUT

THERMO_OUT

32

33

FC_SENS_Vcc

GND

34

35

FC_XA

FC_XB

36

37

FC_A

FC_B

38

39

ZM_SENS_OUT

GND

40

41

ZM_SENS_Vcc

HALL(+)

42

43

BIAS(+)

HALL(-)

44

45

BIAS(-)

GND

46

47

GND

DRIVE(-)

48

49

DRIVE(+)

SLOW SHUT

50

Q3001 UN9213J-(K8).SO

H2 H1

R11.6/P0

RG

GND

CCD_OUT

9

8

R9.9/P0 RG

H1

H2

R-6.7/ P0.4

C3000 10u 10V TA A

R11.6/P0

H1

10

R9.2/P0

H2

11

0

12

R1.3/P0

13

R6.5/P0

14

D

E

4

SUB

5

VL

6

C3001 10p CH

IC3000

C3003 22u 16V B TA

C3002 0.1u F

R8.4/ P0

IC3000

2

BUFFER

L3000 100uH

Q3000 2SC4178-F13F14-T1

V_HOLD

V_DRAIN

V1

V2

V3

R3.7/P0

R-0.3/P0

R-0.3/P0

R-6.3/P0

R-6.3/P0 V4

3

1

6

6

VSHT

0

5

4

V4

5

RG

4

2

3 R3.7/P0

SWITCH

3

V2 V1 V_DRAIN

V3

C3004 XX B

2

50P

1

VDD

B

1

12

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

-REF.NO.:30000 SERIESXX MARK:NO MOUNT

C

11

R3000 2200

7

TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV11 MODEL :DCR-TRV11 TRV11E MODEL:DCR-TRV11E

-6.5V

8

TO VC-241 BOARD CN701

CCD IMAGER

(SEE PAGE 4-26) IC3000 ICX220BKC-13 : TRV6/11 MODEL ICX221BKC-13 : TRV6E/11E MODEL

F

Y

Y/CHROMA

13

14

15

16

17

18

19

20

21

22

23

24

FC_XA

GND

FC_SENS_Vcc

THERMO_OUT

FC_SENS_OUT

GND

NightShot_Vcc

ZM_B

ZM_A

ZM_XB

ZM_XA

D3000 MA8082-(K8).S0

12

FC_XB

8

11

7

ZM_SENS_Vcc

FC_A

6

BIAS(+)

FC_B

5

HALL(+)

9

4

BIAS(-)

10

3

HALL(-)

GND

2

GND

ZM_SENS_OUT

1

SUPER NIGHT SHOT

GND

CN3000

VIDEO SIGNAL CHROMA

DRIVE(-)

24P

SIGNAL PATH

G

DRIVE(+)

S3000

LND300

REC PB

LENS BLOCK

LENS BLOCK is replaced as a block, So that these PRINTED WIRING BOARD and SCHEMATIC DIAGRAM are omitted.

H 16

Precautions Upon Replaching CCD imager • The FP-219 flexible board mounted as a repair part is not equipped with a CCD imager. When replaching this board, remove the CCD imager from the old one and mount it onto the new one. • If the CCD imager has been replaced, carry out all the adjustments for the camera section. • As the CCD imager may be damaged by static electrictiy from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strog light.

4-13

4-14

CCD IMAGER FP-219

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

FP-219 FLEXIBLE BOARD (CCD IMAGER) PRINTED WIRING BOARD — Ref. No. FP-219 Flexible Board; 30,000 Series —

FP-219 FLEXIBLE BOARD (SIDE A) (CCD IMAGER) F

50

2 40

30

20

10

CN3001 45

35

25

15

5 1

49

E Q3001 IC3000 1

10

D

1

5

3

2

5

4

R3001

24 5

10

15

C3000

1

6

C3004

C3003

L3000

14

20

CN3000

C3001

8

7

Q3000 R3000

B C E

7

C3002

C For printed wiring board • This board is two-layer print board. However, the patterns of layers two have not been included in the diagram. • Chip parts Transistor C

B

B

E

There are few cases that the part printed on this diagram isn’t mounted in this model. A

K

D3000

FP-219 (TRV6/TRV6E/TRV11/TRV11E) (CCD IMAGER)

A S3000

1-667-566(From LENS BLOCK) (TRV6/TRV6E/TRV11/TRV11E model)

CCD IMAGER FP-219

4-15

16

1

2

3

4

4-16

11

5

Schematic diagram and printed wiring board of the VC-240/241 board are not shown. Pages from 4-17 to 4-74 are not shown.

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

CK-92 (KEY) PRINTED WIRING BOARD — Ref. No. CK-92 Board; 20,000 Series —

For printed wiring board • Refer to page 4-125 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram. • Chip parts Transistor

Diode

C

B

3

E

2

1

There are few cases that the part printed on this diagram isn’t mounted in this model. VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O

1-677-556-

MA-385 (AUDIO I/O)

SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)

KEY CK-92

4-75

4-76

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

FP-181 FLEXIBLE BOARD (PANEL REVERSE) PRINTED WIRING BOARD

S906 (PANEL REVERSE)

1-677-563-

11

FP-181 FLEXIBLE BOARD

CONTROL SWITCH BLOCK (PS30150) FP-183 (TRV11/TRV11E/TRV20/TRV20E)

1-677-556-

FP-181 FP-182

4-77

4-78

KEY CK-92

/ PANEL REVERSE FP-181

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

CK-94 (KEY) PRINTED WIRING BOARD — Ref. No. CK-94 Board; 30,000 Series —

For printed wiring board • Refer to page 4-125 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram. • Chip parts Transistor

Diode

C

B

3

E

2

1

There are few cases that the part printed on this diagram isn’t mounted in this model. VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O

1-677-559-

MA-385 (AUDIO I/O)

SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)

KEY CK-94

4-79

4-80

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

1-677-559-

4-81

4-82

KEY CK-94

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

For Schematic Diagram • Refer to page 4-75,79 for printed wiring board.

2

1 CK-92 BOARD CK-94 BOARD A

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

(TRV11/11E/20 MODEL) CN3201

(TRV6/6E/20E MODEL)

KEY -REF.NO.:30000 SERIESXX MARK:NO MOUNT

(TRV11/11E/20 MODEL) TO PD-123 BOARD CN2176

1

51

OSD_SO

XOSD_SCK

2

50

XOSD_SCK

3

49

XCS_LCD_DRIVER

LCD_COM/XDATA

4

48

LCD_COM/XDATA

EVER_3.0V

5

47

EVER_3.0V

PANEL_B

6

46

REG_GND

PANEL_G

7

45

PANEL_B

PANEL_R

8

44

REG_GND

PANEL_VG

9

43

PANEL_G

PANEL_COM

10

42

REG_GND

XHD_OUT

11

41

PANEL_R

PSIG

12

40

REG_GND

39

PANEL_VG

TO PD-124 BOARD CN3171

(SEE PAGE 4-97)

B

OSD_SO

XCS_LCD_DRIVER

(SEE PAGE 4-93)

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

CN3205

12P

51P

(TRV6/6E/20E MODEL)

CN3202

C

TO PD-123 BOARD CN2173

(SEE PAGE 4-93) S104

S105

LCD BRIGHT-

LCD BRIGHT+

38

REG_GND

37

PANEL_COM

36

C-SYNC/XHD

35

XVD

34

REG_GND

DISP_HD

1

DISP_VD

2

GND

3

GND

4

PANEL_2.8V

5

33

(TRV11/11E/20 MODEL)

CONTROL SWITCH BLOCK (CF-30150) S106

14P

C3203 10u 25V TA C

MEMORY MODEL

REG_GND

PANEL_13.3V

6

32

REG_GND

PANEL_-15.3V

7

31

HI_SO

PANEL_4.6V

8

30

XHI_SCK

S103

VOLUME-

VOLUME+

TO PD-124 BOARD CN3202

HI_SO

9

29

XCS_LCD

XHI_SCK

10

28

P_UNREG

TO VC-240 BOARD CN003

XCS_LCD_DAC

11

27

P_UNREG

(SEE PAGE 4-62)

(SEE PAGE 4-97)

D

(TRV6/6E/20E MODEL) R106 3300

R104 1200

R105 1500

R103 10k

P_UNREG

12

26

XHD_OUT

P_UNREG_GND

13

25

PSIG

P_UNREG_GND

14

24

P_UNREG_GND

23

P_UNREG_GND

C3201 10u 16V TA B

S100

S102 SEL/PUSH EXEC

PROGRAM AE R3201 0 1/10W

S101

E

EXPOSURE

R102 1500

R101 1200

CN3203 R100 10k

7P

PANEL_2.8V

19

KEY_AD7

D_2.8V

7

18

PANEL_13.3V

KEY_AD7

KEY_AD7

6

17

KEY_AD6

KEY_AD3

KEY_AD3

5

16

PANEL_-15.3V

4

DIAL_B

DIAL_B

4

15

KEY_AD5

3

DIAL_A

DIAL_A

3

14

PANEL_4.6V

2

GND

GND

2

13

KEY_AD4

1

GND

GND

1

12

D_2.8V

11

KEY_AD3

CN100

7P

10

G S97

D3203 01ZA8.2(TPL3)

(PANEL_REV)

6P

CN3204

D3201 01ZA8.2(TPL3)

R3202 22k

R3208 3300

R3205 6800

R3211 1500

R3214 1200

D3202 01ZA8.2(TPL3)

KEY_AD6

BT3201 BATTERY

6P

6

GND

GND

1

5

GND

GND

2

4

PANEL_REV

KEY_AD4X

3

3

PANEL_REV

KEY_AD4X

4

2

GND

GND

5

1

GND

GND

6

S3201

S3203

S3206

S3209

(PANEL_CLOSE)

MEMORY INDEX

MEMORY+

MEMORY-

R3203 22k

R3206 6800

R3209 3300

S3212

S3215

MEMORY MIX

R3212 1500

MEMORY DELETE

R3215 1200

REG_GND

9

REG_GND

8

REG_GND

7

REG_GND

6

SP+

5

REG_GND

4

SP-

3

DIAL_B

2

BATT_LI_3V

1

DIAL_A

2

SP-

1

SP+

MEMORY MODEL

KEY_AD5 CN3206

D3204 01ZA8.2(TPL3)

FP-181 FLEXIBLE

MEMORY MODEL:DCR-TRV11/TRV11E/ TRV20/TRV20E

LND321

S3202

S3204

S3207

S3210

S3213

GND

FADER

BACK LIGHT

DIGITAL EFFECT

TITLE

PB ZOOM

R3204 22k

R3207 6800

R3213 1500

R3210 3300

S3216 MENU R3216 1200

KEY_AD4

LND322 GND R3217 1k

I LND323

16

GND S3205 MEMORY PLAY

S3208 SELFTIMER

S3211

S3214

S3217

S3218

END SEARCH

DATA CODE

DISPLAY

RESET

MEMORY MODEL

KEY

20

D_2.8V

CN96

CK-92/94

XRESET_SW

5

CONTROL SWITCH BLOCK(CF-30150)is replaced as a block. So that this PRINTED WIRING BOARD is omitted.

H

P_UNREG_GND

21

6

GND

TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV11 MODEL :DCR-TRV11 TRV11E MODEL:DCR-TRV11E TRV20 MODEL :DCR-TRV20 TRV20E MODEL:DCR-TRV20E

22

7

LND100

F

C3202 XX 16V TA G

4-83

4-84

2P SP901 SPEAKER

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

LB-64 (EVF BACK LIGHT) PRINTED WIRING BOARD — Ref. No. LB-64 Board; 10,000 Series —

2

1

4

3

5

6

7

LB-64 BOARD EVF BACK LIGHT

A

-REF.NO.:10000 SERIESXX MARK:NO MOUNT NO MARK:REC/PB MODE R :REC MODE P :PB MODE CN2201

CN2202

27P COM

1

1

COM

G

2

2

G

R

3

3

R

B

4

4

B

BLK

5

5

BLK

HCK1

6

6

HCK1

HCK2

7

7

HCK2

HST

8

8

HST

B

RGT TO DD-137 BOARD CN1604

9

9

DCG/CLR

10

10

DCG/CLR

EN

11

11

EN

STB

12

12

STB

VCK2

13

13

VCK2

(SEE PAGE 4-110)

VST

14

14

VST

VSS

15

15

VSS

VSS

16

16

VDD

VDD

17

EVF_BL_GND

18

EVF_BL_GND

19

EVF_BL_4.6V

20

BUFFER

EVF_BL_4.6V

21

IC2201 TC7SET08FU(TE85R)

N.C

26

N.C

27

E

4.6

25

C2204 2200p B

5

24

PWM

10

L2202 10uH 2

VCC

0.4

0.5

LED_K

1

L2201 47uH 3225

R2205 10k

0.5

C2201 0.1u B

3

4.5

4

23

4.6

22

1

N.C DET

T2201 INVERTER TRANS

IC2201

2

D

LCD903 EVF LCD

RGT

THROUGH THE FP-180 FLEXIBLE BOARD

3

C

16P

4

5

6

ND2201 BACKLIGHT

Q2201 FX216-TL1 SWITCHING C2202 33u 10V TA B

LND201

C2203 4.7u B

A

F

LND202 A

R2204 XX

R2203 82

1-677-553-

D2202 XX

R2202 XX

G

For printed wiring board • Refer to page 4-126 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram.

LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER)

H

NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)

There are few cases that the part printed on this diagram isn’t mounted in this model.

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

16 DD-137 (DC/DC CONVERTER)

JK-188 (AV IN/OUT)

INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)

4-85

4-86

EVF BACK LIGHT LB-64

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

JK-188 (A/V IN/OUT) PRINTED WIRING BOARD — Ref. No. JK-188 Board; 10,000 Series —

1-677-552-

For printed wiring board • Refer to page 4-126 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram.

LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)

There are few cases that the part printed on this diagram isn’t mounted in this model.

DD-137 (DC/DC CONVERTER)

JK-188 (AV IN/OUT)

INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)

A/V IN/OUT JK-188

4-87

4-88

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

2

1

3

5

6

7

8

9

10

11

12

13

14

A/V IN/OUT -REF.NO.:10000 SERIESXX MARK:NO MOUNT

C

J3001

Y S

D3001 015AZ8.2-TPL3

3

4

S

2

R3056 10k

R3061 0

2

1.6

47

46

HP_L

44

DV_GND

42

TPA

40

NTPA

38

DV_GND

36

XSJACK_IN

34

S_Y_GND

AM2

OUT2

C_RESET

VCC 2.8

Vref2

0.1

HO2

1.5

HI2 C3061 10u

1.4

LO2

1.4

53

49

LIA2

1.4

GND

XHP_JACK_IN

LIB2

1.5

GND

XAVJACKIN

20

1.5

55

54

48

19

1.0

57

GND

51

18

R3060 1k

C3062 10u

R3057 1M

SIGNAL PATH

R3002 0

R3003 0

VDR005

VDR006

LND033 GND

HP_R

45

4

DV_GND

43

3

TPB

41

2

NTPB

39

1

TPA NTPA

IC3051

DV_GND

37

S_Y_OUT

35

GND

33

LND033

TPB NTPB J3004

4P

GND

32

S_C_GND

S_C_OUT

31

30

KEY_AD2

GND

29

28

LANC_DC

GND

27

26

LANCK_SIG/232C_RD

GND

25

24

XLANC_JACK_IN

LANC_GND/232C_TD

23

VTR_UNREG

21

IR_DRV

19

22

VTR_UNREG

20

GND

18

IR_EM

16

GND

14

XF_TALLY_LED

12

MF_LED

10

MF_B

GND

17

XSIRCS_IN

15

A_4.6v

13

MF_A

11

AU_2.8V

8

ZOOM_MIC_CONT

6

XMIC_MONO

9

EXT_MIC_DET

7

SHOE_MIC_L

5

4

AU_GND

MIC_L

3

2

AU_GND

MIC_R

1

J3003 FB3004 0uH

AUDIO/VIDEO VDR001

FB3005 0uH VDR002

R3004 0 VDR007 FB3007 0uH

J3002

HEADPHONE

FB3008 0uH VDR003 1000p

R3005 0

VDR004 1000p

LND031 GND

VIDEO SIGNAL CHROMA

PS_OUT

C_RST

L_IO

17

E

F

YS_OUT

56

V_IO

16

R3055 10k

58

GND

15

C3059 0.047u B

59

R_IO

14

R3054 22k

G

G

DV IN/OUT

3 R3051 22k

A_2.8V

50

13

C3057 0.047u B

C3055 0.1u B

A_2.8V

52

12

0.8

4

60

1

2

11

C3051 XX

SE3052 (YAW)

3

IC3051 UPC6756GR-8JG-E2

C3054 22u A

1

L3052 10uH

PASS

C3052 XX P

D

1.4 4

S VIDEO

R3001 0

C3067 0.1u B

R3059 1M

OUT1

5

C3066 22u A

R3058 15k

AM1

6

1.4

1.4

1.5 7

Vref1

LIB1

8

HO1

9

GND

10

HI1

C3053 22u A

1.0

R1.8/P0.8

C3056 0.1u B

R0/P1.5

C3064 10u

R3053 22k

C3065 0.33u B

C3063 10u

C3060 0.047u B

LO1

R3052 22k

B

C3058 0.047u B

LIA1

1

SE3051 (PITCH)

C

15

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

JK-188 BOARD A

4

Y

Y/CHROMA

CN3001

AUDIO SIGNAL

LND032

60P

TO VC-240 BOARD CN001

GND

(SEE PAGE 4-65)

REC PB

G

H

28

KEY_AD2

27

LANC_DC

26

LANC_SIG

25

LANC_JACK_IN

24

232C_TO

23

GND

22

VTR_UNREG

21

VTR_UNREG

20

GND

19

IR_DRV

18

IR_EM

17

GND

16

GND

15

XSIRCS_IN

14

XF_TALLY_LED

13

A_4.6V

12

MF_LED

11

MF_A

10

I 16

4-90

(SEE PAGE 4-106)

MF_B

9

AU_2.8V

8

ZOOM_MIC_CONT

7

EXT_MIC_DET

6

XMIC_MONO

5

SHOE_MIC_L

4

AU_GND

3

MIC_L

2

AU_GND

1

MIC_R CN3002

4-89

TO MA-385 BOARD CN2071

28P

A/V IN/OUT JK-188

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

PD-123 (LCD DRIVE, RGB DRIVE) PRINTED WIRING BOARD — Ref. No. PD-123 Board; 20,000 Series — 3

4

5

6

7

8

CONTROL SWITCH BLOCK (FK-30150)

A CN008

B

CN062

39P N.C.

39

SHOE_UNREG

38

SHOE_UNREG

37

SHOE_UNREG

1

LANC_SIG

36

LANC_SIG

2

SHO_ID1

35

CN63

SHO_ID1

3

SHO_ID2

34

SHO_ID2

4

33

SHOE_MIC_R

5

MIC_GND

32

MIC_GND

6

31

SHOE_GND

30

SHOE_GND

29

MS_VCC

28

INS

27

BS

26

GND

25

8

N.C.

7

STATICS_GND

6

VSS

5

BS

4

DIO

3

INS

2

SCLK

1

VCC

8P

10

CN51

11

FP-183 FLEXIBLE

8P N.C

8

STATICS_GND

7

VSS

6

1

VSS

BS

5

2

BS

DIO

CN52

INTELLGENT ACCESSORY SHOE

4

3

VCC

INS

3

4

DIO

SCLK

2

5

N.C

VCC

1

6

INS

7

TO VC-240 BOARD CN008

(SEE PAGE 4-65)

D

DIO

24

SCLK

23

GND

22

XEJECT_SW

21

IR_LED_VCC

20

N.C

8

SCLK

9

VCC

10

VSS

IR_LED_ON

19

KEY_AD_0

18

MT_4.75V

17

FK_LED_ON

16

MT_4.75V

15

KEY_AD_1

14

GND

13

XMS_ACCSEE

12

MS_LED_VCC

11

XPHOTO_FREEZE

10

R073 150

S61 EJECT

R063 1200 S062

IR_LED

S069

GND

9

ZOOM_AD

8

D_2.8V

7

D64

R072 470

D66

S066

FF

S068

D62

D65

PAUSE

R068 1500

S067

R067 3300

S072

S71

R069 6800

PHOTO (FREEZE)

LINE IN/OUT MODEL 30150

F

D63

R071 150

(MS ACCESS) REC

E

R070 150

MEMORY MODEL

(SWITCH BACK LIGHT)

S065

PLAY

R074 1200

D70

D69

R066 6800

S064

REW

S070 D73

R065 3300

R064 1500 S063

STOP

MS_ACCSEE

MEMORY STICK CONNECTOR

8

SHOE_GND

D72

10P

7

SHOE_MIC_L

LINE IN/OUT MODEL

C

12

8P

SHOE_MIC_R

SHOE_MIC_L

9

ENDSERCH -

ENDSERCH +

IR_ON

(PHOTO REC)

R085 0

RV61

MEMORY MODEL

CONTROL SWITCH BLOCK (PS-30150)

GND

6

XPHOTO_STBY_SW

5

XS/S_SW

4

XVTR_MODE_SW

3

N.C.

2

1

XPHOTO_STBY_SW

XCAM_STBY_SW

1

2

XCAM_STBY_SW

CN064

6P

3

GND

4

XVTR_MODE_SW

5

XS/S_SW

N.C.

6

XS/S_SW

5

XVTR_MODE_SW

4

START/STOP

S1

S2

POWER

S/S

VTR

1-677-557-

2

1

(VTR) GND

3

XCAM_STBY_SW

2

XPHOTO_STBY_SW

1

RV61

OFF (CAM)

6 ZOOM

CAMERA (PHOTO) PHOTO

T

G

W

CONTROL SWITCH BLOCK(FK-30150,PS-30150) is replaced as a block.so that this PRINTED WIRING BOARD is omitted. MEMORY MODEL :DCR-TRV11/TRV11E/TRV20/TRV20E LINE IN/OUT MODEL:DCR-TRV6/TRV6E:E,HK,AUS,CN,JE,/TRV11/ TRV11E:E,HK,AUS,CN,JE/TRV20/TRV20E

16

For printed wiring board • Refer to page 4-126 for parts location. • This board is four-layer print board. However, the patterns of layers two to four have not been included in the diagram. • Chip parts

LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER) DD-137 (DC/DC CONVERTER)

Transistor C

B

E

JK-188 (AV IN/OUT)

PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)

There are few cases that the part printed on this diagram isn’t mounted in this model.

CONTROL SWITCH BLOCK FK-30150

/ LCD DRIVE, RGB DRIVE PD-123

INVERTER TRANSFORMER UNIT

4-92

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

For Schematic Diagram • Refer to page 4-113 for waveform.

2

3

PD-123 BOARD(1/2)

4

5

6

8

9

(TRV11/11E/20 MODEL) SEG11

SEG12

SEG13

SEG14

COM2 SEG2 SEG3

1.5

1.5

1.5

SEG15

1.5

SEG16

1.5

1.5

-REF.NO.:20000 SERIESXX MARK:NO MOUNT NO MARK:REC/PB MODE R :REC MODE P :PB MODE

SEG4 SEG5

SEG11

SEG12

SEG13

SEG14

SEG15

SEG17

SEG18

32 31 30 29 28 27 26 25

SEG6 SEG7

1

B

OSC1

2

2.0 3 4

3.0 3.0 6

LCD DRIVE

VLCD

IC2171 BU9735K-E2

SEG5

7

SEG4

8

SEG3 SO

1.5 1.5 1.5 1.5 1.5 1.5 1.5

SEG10

VG

10

COM_OUT

XHD_OUT

11

XHD_OUT

PSIG

12

PANEL_VG

CN2173

2

TO(2/2)

14P DISP_HD

1

SYNC

DISP_VD

2

XVD

REG_GND

3

REG_GND

4

TO(2/2) C2174 10u 6.3V

SEG9

SEG10

SEG8

SEG11

SEG7

SEG12

SEG6

SEG13

SEG5

SEG14

SEG4

SEG1

SEG3

SEG16

SEG2

4

SEG3

5

SEG4

6

SEG5

7

SEG6

8

SEG7

9

SEG8

10

SEG9

11

SEG10

12

SEG11

13

SEG15

CHARACTER DISPLAY

SEG12

14

SEG13

15

SEG14

16

SEG1

17

SEG16

18

COM4

SEG2

SEG1

COM2

3

SEG15

19

COM3

20

COM4

21

N.C

1.5

1.5

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Q2173 2SB1462J-QR(K8).SO BACK LIGHT SWITCH 4.5 0

L2173 100uH

3

2

13

21P

SEG2

TO(2/2)

COM1

2.9

9

PANEL_COM

1

SEG1

PANEL_R

COM4

8

1.5

PANEL_G

PANEL_R

COM4

PANEL_B

7

COM3

6

PANEL_G

1.5

5

PANEL_B

COM1

12

10 11 12 13 14 15 16

COM3

EVER_3.0V

9

COM2

4

COM1

LCD_COM/XDATA

1.5

3

COM2

XCS

2

C/XD

XOSD_SCK

0

1

1.5

OSD_SO

1

11

LCD902

SEG9

COM3

XCS_LCD_DRIVER

E

SEG6

1.5

12P

(SEE PAGE 4-83)

D

SEG7

VC

SCK

0.1

TO CK-92 BOARD CN3201

SEG8

VDD

2.8

CN2176

SEG9

IC2171

VSS

3.0

C

1

OSC2

5

C2180 0.01u B

SEG10

17 18 19 20 21 22 23 24

SEG8 R2180 680k 1.5

10 CN2175

COM1

LCD DRIVE

A

7

SEG16

1

C2175 0.1u B

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

R2175 4700 3.7 R2176 1k BL

TO CK-92 BOARD CN3202

(SEE PAGE 4-83)

F

PANEL_2.8V

5

PANEL_2.8V

PANEL_13.3V

6

PANEL_13.3V

PANEL_-15.3V

7

PANEL_-15.3V

PANEL_4.6V

8

PANEL_4.6V

HI_SO

9

XHI_SCK

10

XCS_LCD_DAC

11

P_UNREG

12

P_UNREG_GND

13

P_UNREG_GND

14

0

2.7

(STARTER) 13P

REG_GND

XHI_SCK

4

5

BACK LIGHT SWITCH

TO(2/2)

TO(2/2)

L2172 4.7uH C2172 47u 16V

HI_SO

7

Q2172 UN9214J-(K8).SO

6

C2182 XX C2173 0.1u B

R2177 0

1

BL_GND

BL_DET

2

LED

PWM

3

BL_LOW

4

NC

5

NC

6

NC

7

NC

8

NC

5P

CN2174 1

PWM

2

PANEL_4.6V

3

BL_DET

4

P_UNREG_GND

5

P_UNREG

5P PWM PANEL_4.6V

5 4

BL_DET

3

P_UNREG_GND

2

P_UNREG

1

TO(2/2)

XCS_PANEL

R2178 XX

LND217 A

G

TO(2/2)

SIGNAL PATH

INVERTER UINT

9

NC

10

NC

11

NC

12

NC

13

BL_HI

ND901 BACK LIGHT

VIDEO SIGNAL CHROMA

Y

Y/CHROMA

REC PB

H 16

TRV11 MODEL :DCR-TRV11 TRV11E MODEL:DCR-TRV11E TRV20 MODEL :DCR-TRV20

4-93

4-94

LCD DRIVE PD-123 (1/2)

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

For Schematic Diagram • Refer to page 4-92 for printed wiring board. • Refer to page 4-114 for waveforms.

2

PD-123 BOARD(2/2)

5

6

7

L2103

L2104

0

6.7

COM_OUT

24 23 22 21 20 19 18

C2122 6.8u 16V TA A

17

N.C

4.5 13.5

C2124 0.1u B

C2125 1u 3216 B

C2123 0.1u B

*

R2140

4

5

6

7 0

3

L2102 10uH

8

9

10

*

D2103

11

TG24

12

TG23 TG22

R2113 2700 R2116 68k

C2114 0.1u B

R2114 47k

TG21

R2120 100k R2119 1M

C2108 10u 6.3V TA

* R2122

N.C

2

1

D2102 1T369-01-T8A

C2113 560p CH

R2117 22k

G

R2118 68k

TG19 TG12

* C2118

R2126

TG16 TG15 TG14 TG13 XP.SAVE

* C2127 25V TA *

*

XC.SAVE

XHI_SCK

C2128 R2111 0.1u B Q2107 100k 1608 2SD2216J-QR(K8).SO

6

XCS_PANEL

RGB DRIVE PD-123 (2/2)

XHD_OUT

VG

19

VR

18

HCNT

17

MCLK

16

CLR

15

OE

14

SRT

13

STBYB

12

VBC

11

VCOM

10

RESET

9

STBYB

8

GSRT

7

GPCK

6

GRES

5

N.C.

4

VDD

3

VGL

2

VSS

1

VGH

LCD901

*

*MARKED:MOUNT TABLE TRV11/11E MODEL

Q2102 *

6

7

8

9

10

11

12

XX

0.01u 16V B

XX

C2131

0.01u 16V B

XX

C2132

C2118

82p 16V CH

56p 16V CH

D2103

MA111-TX 871940450

XX

L2105

3.3uH ± 5%

2.2uH ± 5%

IC2105

LZ9FF424

CM7019L2-T

IC2106

TC7SET04FU

XX

Q2102

MGSF1P02LT

XX

Q2103

2S81462J-Q

XX

Q2104

2SD2216J-Q

XX

Q2105

2S81462J-Q

XX

Q2106

2SD2216J-Q

XX

R2101

XX

0

R2103

0

XX 56k

* *

*

5

1 2

R2125 0uH

0

TG23

4

C2131 B

IC2106

* Q2105 R2145 XX

TG22 *

2.6

Q2106

R2150

TG21

0

C2132 B

*

DR.P.SAVE CPMODE/CLS

5

1u 25V

TG24 R2127 120

3

OSCI

OSCO

4

1.3

(Note)

*

XC.SAVE

3

TRV20 MODEL

C2127

*

PD

2

R2147

R2151

TG20 * R2103

2.7

TG19

0

TG18

2.7

TG17

0

TG16

0.1

TG15

2.5

TG14

0.5

TG13

* R2149

R2141 10k

BL_DET

Q2108 UN9213J-(K8).SO

7 PWM

TO(1/2)

BL

SIGNAL PATH

R2123

VIDEO SIGNAL CHROMA

TG12

Y

R2122

XX

R2123

XX

0

R2124

0

XX

R2126

Y/CHROMA

16

4-96

XX

0

R2140

XX

0

R2143

180k

XX

R2144

PB

4-95

VB

20

* Q2104

REC

XCS_PANEL

TO(1/2)

M

2.5

2.7

L

SYNC

1.4

*

PS/VDD

TESTI

HI_SO

24

GND

TESTI

XVD

HI_SO

23

-IN/TESTO

PWM

XVD

2.7

TO(1/2)

2.7

8

SYNC

22

+IN/TESTO

1

XHD_OUT XHD_OUT

CP/SPS

21

OUT/TESTO

9

16

LED

XVD

GPCK/MODE1 GRES/EX1

2.7

VSYB

20

37 38 39 40 41

10

SI

TESTI/GND

2.6

STBYB/SPG GSRT/MODE2

GND/TESTI

1.1

SO

BL-DET

HI_SO

XCS

RESET/EX2

BL-ON

2.6

11

W/H

XTG_SO

VDD/RES

* IC2105

VDD/TESTI

MCLK/CLD

SRT/PSS1

TIMIING GENERATOR

XSCK

HCNT/SPD

OE/PSS2

12

IC2105

R2101

14

CLR/CTR

HDB

3.0

K

SYNC

VSS

21

IC2106

19

25

18

26

17

27

16

28

15

29

14

30

HDI

XCS_PANEL

COM_FRP

42

2.4 2.7

3

22

R2148

13

31

13

FRP

43

1.3

44

1.3

XVD

2.7

32

SW

45

FRP COM_FRP

SWCOM

46

0.1

XHI_SCK

0

33

15

BGP

47

0

48

J

1.4

34

13.5

35

I

BLK

0

0

2.7

36

R2142 470k

BGP

1.4

C2109 0.1u

SYF

2.7

POCB

0

0

D2101 MA111-TX

C2130 1u B 3216

* R2144

R2146

Q2103

*

H

VDD

TG17

* R2121

TO(1/2)

VSH

23

TG18

* L2105

XHI_SCK

24

LCD

TG20

C2117 1000p SL

* R2124

C2110 0.1u B

TO(1/2)

R2129 10k

C2121 1u B 2012

16

43

1.7

2

CN2101

N.C

4

VR

13

R_IN

C2133 XX CH

2.2

VG

C2120 1u B 2012

VG

14

3

1.7

15

Vcc4

G_IN

2.2

C2119 1u B 2012

VB

N.C

COM_OUT

B_IN

1.7

N.C

0.01u

C2135 XX CH

VSH

VCO

C2107

PANEL_R

1.8

2

XP.SAVE

VB

2.2

0

0.01u

GND1

OP_OUT

C2106

LPF_ADJ 2.7

OP_IN-

0

PANEL_G

GND2

0

R2152

1.7

TRAP_ADJ 1.1

OP_IN+

0.01u

VR

R_DC_DET

IC2104 RB5P003AM1

0

C2105

5

RGB DRIVE

Vcc1 1.1

BIAS

0

XCS

VG

G_DC_DET

0

R2154

1.7

46

XP.SAVE

0

47

C2101 C2102 68u 0.1u 4V TA B

R2153 PANEL_B

48

C2134 XX CH

C2104 XX R2109 R2107 27k XX ± 0.5%

IC2104

SI

N.C

38 39 42

R2108 0 XX C2103 XX R2106 33k ± 0.5%

6

N.C

L2101 10uH

VB

B_DC_DET

XSCK

N.C

0

XC.SAVE

N.C

XCS_PANEL

7

EXT_DA2

N.C

0

40

XTG_SO

41

2.4

44

D

XHI_SCK

45

R2105 470k

0

37

1.6 XC.SAVE

VG

FRP

COM_FRP

25

100

GND3

26

R2135

27

VR

28

100

29

100

30

R2133

31

R2134

32

13.5 Vcc3

33

Vcc2

FRP

COM_FRP

34

BLACK_IN

0

1.3

BLK

35

N.C

0

0.1

36

* R2143

5

18

C2115 0.1u B

C2112 0.1u B 1608

BGP

0

C2111 3.3u 20V TA

EXT_DA1

0

BGP

C2129 0.01u B

R_INJECT

C

F

17

16

C2116 10u 10V TA A R2112 15k

TO(1/2)

15

14

10uH

PANEL_2.8V

1

13

10uH

PANEL_4.6V

REG_GND

E

12

TRV11 MODEL :DCR-TRV11 TRV11E MODEL :DCR-TRV11E TRV20 MODEL :DCR-TRV20

PANEL_13.3V

B

11

(Note) Inductor is mounted to the location where R2125 is printed.

PANEL_-15.3V

TO(1/2)

10

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

-REF.NO.:20000 SERIESXX MARK:NO MOUNT

4

9

8

(TRV11/11E/20 MODEL)

RGB DRIVE

A

4

3

*

1

XX

0

R2146

XX

0

R2147

10k

XX

R2148

47k

XX

R2149

XX

0

R2150

1M

XX

R2151

1M

XX

R2121

1M

XX

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

For Schematic Diagram • Refer to page 4-101 for printed wiring board. • Refer to page 4-114 for waveform.

SEG16

(TRV6/6E/20E MODEL)

LCD DRIVE -REF.NO.:30000 SERIESXX MARK:NO MOUNT

8

9

10

11

1.5

1.5

1.5

1.5

1.5

1.5

SEG11

SEG12

SEG13

SEG4

SEG14

SEG3

SEG16

2

COM2

3

SEG2

4

SEG3

5

SEG4

6

SEG5

7

SEG6

8

SEG7

9

SEG8

10

SEG9

SEG5 SEG6

3

2

1.9

3.0

4

C3171 0.01u B

5

3.0

6

3.0

7

2.9 0.1

8

C

SEG10

OSC1 SEG9 OSC2

IC3171

VSS

SEG8 SEG7

VC SEG6

IC3171 BU9735K-E2

VLCD

SEG5

VDD SEG4 SCK SEG3 SO

1.5 1.5 1.5 1.5 1.5 1.5 1.5

SEG10

SEG7

SEG9

SEG8

SEG8

SEG9 SEG10

SEG7

SEG11

SEG6

SEG12

SEG5

SEG13

SEG4 SEG3

1.5

SEG16

SEG2

SEG1

COM4

COM3

COM2

XCS

2

COM1

XOSD_SCK

1

SEG10

12

SEG11

13

SEG12

14

SEG13

15

SEG14

16

SEG1

17

SEG16

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

LCD XXX

SEG1

SEG15 OSD_SO

11

14

SEG14

12P

C/XD

CN3171

1

1.5

1

R3174 680k

17 18 19 20 21 22 23 24

B

13

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

SEG2

32 31 30 29 28 27 26 25

SEG17

COM1

COM2

SEG18

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

1

12

21P

CN3173 COM1

SEG15

A

7

SEG11

6

SEG12

5

SEG13

PD-124 BOARD(1/2)

4

SEG14

3

SEG15

2

1

18

SEG15

COM3 19

COM3

20

COM4

21

N.C

COM4

PANEL_R

2.9

9

VG

PANEL_COM

10

COM_OUT

XHD_OUT

11

PSIG

12

PANEL_VG

TO(2/2)

2

TO(2/2)

3

TO(2/2)

1

SYNC

DISP_VD

2

XVD

REG_GND

3

REG_GND

REG_GND

4

R3175 4700

4

TO(2/2)

5

TO(2/2)

4.6

4.6

14P DISP_HD

Q3172 2SB1462J-QR(K8).SO

L3172 100uH

PSIG XHD_OUT

CN3172

E

1

1.5

8

SEG2

PANEL_R

1.5

PANEL_G

SEG1

PANEL_B

7

1.5

6

PANEL_G

COM4

PANEL_B

(SEE PAGE 4-83)

COM1

D

1.5

5

COM3

EVER_3.0V

10 11 12 13 14 15 16

1.5

TO CK-94 BOARD CN3201

9

COM2

4

0

3

LCD_COM/XDATA

1.5

XCS_LCD_DRIVER

3.8 R3176 1k

(STARTER) BL

TO CK-94 BOARD CN3202

(SEE PAGE 4-83)

F

G 16

PANEL_2.8V

5

PANEL_2.8V

PANEL_13.3V

6

PANEL_13.3V

PANEL_-15.3V

7

PANEL_4.6V

8

HI_SO

9

6

C3175 10u 6.3V

TO(2/2)

C3176 0.1u B

2.8

R3171 0 R3172 0

L3171 4.7uH

HI_SO

7

C3177 XX

R3178 XX

CN3174

2

PANEL_4.6V

3

BL_DET

13

4

P_UNREG_GND

14

5

P_UNREG

XCS_LCD_DAC

11

P_UNREG

12

P_UNREG_GND P_UNREG_GND

R3173 0

XHI_SCK

TO(2/2)

XCS_PANEL

C3173 47u 16V

C3174 0.1u B

TO(2/2)

R3177 0 PWM

10

9

BL_DET A Q3171 UN9214J-(K8).SO

13P TO(2/2)

LND311

TA P

1

XHI_SCK

8

PWM

0

5P

4-97

BL_GND

2

LED

3

BL_LOW

4

NC

5

NC

6

NC

7

NC

8

NC

9

NC

10

NC

11

NC

12

NC

13

BL_HI

5P PWM PANEL_4.6V

1 2

BL_DET

3

P_UNREG_GND

4

P_UNREG

5

INVERTER UINT

TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV20E MODEL:DCR-TRV20E

1

ND901 BACK LIGHT

4-98

LCD DRIVE PD-124 (1/2)

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

For Schematic Diagram • Refer to page 4-114 for waveforms.

2

1

3

PD-124 BOARD(2/2)

4

(TRV6/6E/20E MODEL)

6

7

8

9

10

11

12

13

14

15

16

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

LCD DRIVE

A

5

-REF.NO.:30000 SERIESXX MARK:NO MOUNT L3101 10uH

13.5

Q3103 NDS356AP

13.5

PANEL_13.3V

C3116 0.01u B

24 23 22 21 20 18

19

C3121 1u

R3160 100k

C3104 10u 6.3V TA P

C3113 1000p SL

* R3115 XX

13.5

* L3104

32

31

30

29

28

27

26

25

SHB 0.9

SHA 0.9

GND

TESTI/VDD

RPD 1.4

XCSAVE 2.8

OSCI 1.4

OSCO 1.4

XSTBY 2.8

POFF

10

NC

1

2

SYNC

2.8

3

4

5

6

7

8

9

10

11

24 23 22 21 20 19 18 17 16 15

RGT

14

SI

XVD

0

9

CRext

TG16

8

HCK2

7

HCK1

6

PSIG

5

G

4

R

3

B

2

* R3143 R3157 100k

RGT

1

TEST2 CN3101

24P

Q3105 XP4601-TXE

PWM

TG24

8 TO(1/2)

BL

3 TO(1/2)

XHD_OUT

2.2 TG22 2.8 TG21 0.1 TG20

SIGNAL PATH *MARKED:MOUNT TABLE

VIDEO SIGNAL

2.8 0

CHROMA

TG18

1.4 TG17

REC

1.4 TG16

PB

Y

2.8 TG15 2.8

TG14

TRV20E MODEL

TRV6/6E MODEL

C3117

39p 16V CH

47p 16V CH XX

C3129

1u 10V B XX

1u 10V B

Y/CHROMA

C3132

TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV20E MODEL:DCR-TRV20E

D3103

RD2.7UM-T1

XX

D3104

XX

RD3.3UM-T1

L3104

2.2uH ± 5%

3.3uH ± 5%

R3137

56k

XX

R3143

0

XX

R3144

XX

0

R3146

110k

XX

12

R3139 6.8k

Q3108 UN9213J-(TX).SO

4-99

TEST

TG17

1.4 TG23

16

PD-124 (2/2)

10

LCD

R3133 10k

M

RGB DRIVE

REF

6.1

C3126 0.1u B

0.1

BL_DET

HST

11

6.1

13

HCK1

2.6

L

HCK2

SO

VDO

12

Q3106 XP4601-TXE

TEST/GSPB

8

XCS

TEST/GPWCB

4 TO(1/2)

HST

IC3102 CXD3505R-T4

TEST/GPWC

2.8

VDD

PWM

47 48

XVD

VDD

LED

K

2.5

IC3102

XSCK

WIDE

6.7

6.7

2.8

2.7 46

HI_SO

WIDE

TESTI/GND

3.0 45

XTG_SO

PFRP

GND

2.8 44

XCS_PANEL

DWN

2.8

42 43

2.6

EN

FRP

DETIN

1.4 XHI_SCK

SBLK

BL

41

J

1.4

VCK

2.8

PFRP

PRG

XWRT

0 40

FRP

13

Q3104 2SB1462J-QR(K8).SO

VST

9

HDO

2.8 39

BLK

XCLP

0.3

PRG

CS

TG18

TG14

33

SHG 2.8

XP.SAVE

XC.SAVE

34

SHR 0.9

SH4

SH3

35

XCLR 2.8

SH2

36

HD

37 2.7

XCS_PANEL

XCS_PANEL

9 TO(1/2)

R3128 100k

BGP

XHI_SCK

38

XHI_SCK

14

1.7 1.1

SH1 HI_SO HI_SO

7 TO(1/2)

VSSG

TG20

13.5

6.7 * C3117 CH

D3101 MA111-TX

I

VDDG

15

* D3104

C3130 0.1u

7.3

R3127 220k

H

VSS/GND

16

TG15

D3102 1T369-01-T8A

C3131 0.1u B

VDD

17

R3159 R3158 100k 100k

2.8

R3107 470k

DWN

18

B

R3113 100k

0

EN

19

R

R3132 10k

R3131 100k

R3116 1M

C3112 R3114 68k 560p CH

R3135 100k

C3111 0.1u B

C3106 0.1u B

20

G

R3118 ± 0.5% XX B

C3122 XX F

2.3

Q3107 2SD2216J-QR(K8).SO

VCK

TG21

LCD901

R3120 XX ± 0.5%

R

3.2

R3117 0

6.7

L3103 10uH

21

* D3103

R3134 150k

G

G

VST

TG22

6.4

C3115 0.1u

R3112 22k

COM

TG23

22

* R3144

* C3132

R3136 0

VG

VB

VR

VP R3124 100

R3123 10

C3123 XX F

R3109 0

R3110 47k

TEST1

23

* C3129

12

R3111 68k

C3128 4.7u

24 TG24

* R3137 R3119 XX

R3121 10

0 COM_IN

* R3146

R3122 10

16 15

17

D3105 MA111-TX

COM_DC

11 1.5

10

VCO

OP_OUT

OP_IN9 1.4

8 1.4

7 1.4

6

OP_IN+

BIAS

N.C

SH_A 5 0.9

0.9

4

SH2

2.8

3

SH1

F

SH_B

XSH.SAVE

2

1

2 TO(1/2)

PSIG COM_OUT

R3138 XX

1.7 Vcc2

1.4 XVP.SAVE

2.8 VP

FRP

PFRP

2.8 FRP

1.4 PFRP

BLK

0 PRG

N.C

EXT_DA

13.5 0 COM_OUT

14

42 43 45

C3135 CH 120p

C3134 CH 120p

13.5 Vcc3

4

VG

C3120 1u VR

6.7 VREF

3

R_IN

1.8 C3133 CH 120p

2

0.9

100

PANEL_R

GND1

G_IN

1.8 48

R3142

1.8

C3110 0.01u B

LPF_ADJ

SH4

PANEL_G

GND2

C3119 1u VG

6.7 VR 1.7 R_DC_DET

IC3101 RB5P004AM1

2.8

E

C3108 0.01u B

5

TRAP_ADJ

B_IN

R3126 0

VB

1.7 G_DC_DET

XP.SAVE

2.8

C3109 0.01u B

IC3101

SH3

1 TO(1/2)

100

1.1 XP.SAVE

6.7

6.7 VG

6

Vcc1

44

100

PANEL_B R3141

1.1

0

Q3102 UN9213J-(TX).SO

VB 1.7 B_DC_DET

SH_R

R3140

2.8

C3107 0.01u B

0

25

26

NEW-DRIVER

46

REG_GND

R3104 XX

R3105 33k ± 0.5%

5 TO(1/2)

C3103 XX SL

R3102 33k ± 0.5%

C3102 0.1u B

C3101 68u 4V B

27

7

XCS

3.0

PANEL_2.8V

28

2.7 SI

47

D

R3101 XX

C3127 0.01u B

R3125 470k

2.8

29

13

37 XCS_PANEL L3102 10uH

30

2.6 XSCK

40

XTG_SO

31

C3125 XX B

VP

N.C 2.8 XC.SAVE

39

XHI_SCK

32

C3114 1u B

1.1

38

XC.SAVE

41

R3106 470k

33

BGP 2.7 BLACK_IN

C3105 0.01u B REG_GND

34

SH_G

6 TO(1/2)

C

35

R_INJECT 0.7

36

PRG

BGP

R3108 15k

6.7 P_DC_DET

B

C3124 XX 20V TA A

C3118 3.3u 20V TA A

4-100

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

SE-107 (MANUAL FOCUS) PRINTED WIRING BOARD

— Ref. No. PD-124 Board; 30,000 Series —

— Ref. No. SE-107 Board; 4,000 Series —

1-677-554-

PD-124 (LCD DRIVE, RGB DRIVE) PRINTED WIRING BOARD

1-677-560-

For printed wiring board • Refer to page 4-126 for parts location. • This board is four-layer print board. However, the patterns of layers two to four have not been included in the diagram. • Chip parts

For printed wiring board • Refer to page 4-127 for parts location. • This board is four-layer print board. However, the patterns of layers two to four have not been included in the diagram.

There are few cases that the part printed on this diagram isn’t mounted in this model.

LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER)

VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O

MA-385 (AUDIO I/O)

NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)

SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)

DD-137 (DC/DC CONVERTER)

Transistor C

B

E

JK-188 (AV IN/OUT)

INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)

There are few cases that the part printed on this diagram isn’t mounted in this model.

4-101

4-102

LCD DRIVE, RGB DRIVE PD-124

/ MANUAL FOCUS SE-107

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

MA-385 (AUDIO I/O) PRINTED WIRING BOARD — Ref. No. MA-385 Board; 10,000 Series —

I/O LANC

1-677-551-

For printed wiring board • Refer to page 4-127 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram. • Chip parts Transistor

VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O

Diode

C

3 MA-385 (AUDIO I/O)

B

E

2

1

There are few cases that the part printed on this diagram isn’t mounted in this model.

AUDIO I/O MA-385

4-103

4-104

SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

7

8

9 C2045 0.1u B

MA-385 BOARD

F

R2020 22k

R2017 2.2k

1k B

R2016

1.5

1.5

1.5

1.5

1.5

1.5

C2024

0.1

1.5

R_OUT

7

8

9

C2016 XX

HPF_AMP_IN_R

6

4

1.5

MIC_L

1.5

XMIC_MONO

2.7 R2032

2.8

R2033

1.5 2.8 2.7

C2037 10u C2036 0.1u B

0.1

6.3V

ZOOM_MIC_CONT

1200 33k

D2061 TLSU1002(TPX1,SONY)

TA P C2038 0.22u F

R2034 18k

R2061 XX

(TALLY) EXT_MIC_DET

1.9

R2065 470

1.5 R2031 33k

L2001 10uH 2520

MIC_R

R2029 XX

C2034 XX B

ZOOM_MIC_CONT EXT_MIC_DET

C2030 XX B

XMIC_MONO SHOE_MIC_L

100p

CH C2020 0.1u R2022 22k

C2025 0.068u B 1608

MIC_L

C2026 0.022u B 1608

MIC_R

R2028 22k R2025 0 R2026 27k

4

IC2091

C2032 0.015u B

KEY_AD2

27

LANC_DC

26

LANC_SIG

25

LANC_JACK_IN

24

232C_TD

23

GND

22

VTR_UNREG

21

VTR_UNREG

20

GND

19

IR_DRV

18

IR_EM

17

GND

16

GND

15

XSIRCS_IN

TO JK-188 BOARD CN3002

14

XF_TALLY_LED

(SEE PAGE 4-90)

13

A_4.6V

12

MF_LED

11

MF_A

10

MF_B

9

AU_2.8V

8

ZOOM_MIC_CONT

7

EXT_MIC_DET

6

XMIC_MONO

5

SHOE_MIC_L

4

AU_GND

3

MIC_L

2

AU_GND

1

MIC_R

5

MF_LED_B

MF_LED_B

5

4

MF_LED_A

MF_LED_A

4

SE-107 BOARD MF SENSOR CN2051

-REF.NO.:4000 SERIESXX MARK:NO MOUNT

5P

3 C2091 10u 6.3V TA

IC2091 RS-70-TU

REMOTE COMMANDER RECEIVER

28P

28

R2051 220

R2091 47

4.5

C2031 0.0033u B

R2052 220

GND

3

MF_B

MF_B

2

MF_A

MF_A

1

3

GND

2 1

2

4.4

1

R2035 0

D2091 MA2S111-(K8).SO

H C2072 10u 16V TA B

SIGNAL PATH VIDEO SIGNAL CHROMA

Y

Y/CHROMA

AUDIO SIGNAL

D2072 DCR2815

REC

Q2071 2SD999-T1-CLCK

D2071 DAC3825

16

LASER LINK

4-105

R2071 18 1/16W

R2072 10 1/10W 2012

PH082 GP1S93

Q2074 2SB1462J-QR(TX).SO

R2073 47k 7.9

0.1 0.1

C2071 0.1u B

PB

R0.1/ P0.3

8.0

8.0 7.9

PH081 GP1S93

R2075 6.8 1/16W 1608

Q2072 2SB624-T1BV4 0.5 8.0

I

D2063 MAZJ200D0LS0

CN2071

C2039 22u 4V TA

10 11 12

C2022 0.1u B

R2018 2.2k

C2042 0.001u B

NC

1.5

5

3

HPF_OUT_R

2

1.5

1

SUB_IN_R

MTX_AMP_OUT_R

MTX_AMP_IN_R

C_1/2VCC

13 14 15 16 17 18 19 20 21 22 23 24

HPF_ON/OFF

GND

R2014 6800

A

R2030 XX

HPF_OUT_L

MTX_AMP_OUT_L

MTX_AMP_IN_L

SUB_SIG_OUT_L

SG_IN_L

INVT_OUT_L

EXT_MIC

MIX_OUT

1.5

D2001 01ZA8.2(TPL3)

D2002 01ZA8.2(TPL3)

VCC

IC2002 AN2901FHQ-EB

C2013 100p CH

MODE_CTL_2 1.5 AMP_OUT_L

ZOOM_POSI

C2009 0.0047u B C2011 0.001u B

ZOOM_BAL

NC

C2005 0.022u B

G C2043 2200p B

INFINITY

R2064 820

HPF_AMP_IN_L

R2021 9.1k

LND001

MAN

R2063 22k

manual Focus

MIC AMP

C2017

C2041 0.001u B

C2035 XX B

C2033 XX B

ZOOM_AMP_IN

1.5

1.5

J2001 MIC (PLUG IN POWER)

FOCUS AUTO

MIC_MONO

1.5

1.5

FB2003 0uH

C2027 0.022u B 1608

IC2002

ZOOM_AMP_OUT

SUB_SIG_OUT_R

1.5

FB2002 0uH

DIGITAL I/O

J2002

LANC

L_OUT

INVT_OUT_R

C2008 0.01u B R2010 10k

FB2001 0uH

17

S2061 R2039 XX

NC

1.5

1.5

E

FB2061 0

(Note)

R2027 22k

GND NC

SG_IN_R

1.5

C_REG

1.5

R2009 4700

1.3

48 47 46 45 44 43 42 41 40 39 38 37

C2010 10u 6.3V P

C2012 10u 6.3V P

16

36 35 34 33 32 31 30 29 28 27 26 25

C

D

C2046 0.1u B

0.1u

C2007 0.022u B

AMP_OUT_R

4

2.4

3

INT MIC GND

REG_2.5V

2

INT MIC R

1k

INT MIC GND

R2015

MIC

1.5 SUB_IN_L R0/P1.5 INT_IN_L

R-CH

1

C2047 0.1u B

R2062 12k

REG_2.5V R0/P1.5 EXT_IN_R 2.2 MODE_CTL_1

MIC

INT MIC L

C2015 0.001u B

INT_IN_R

L-CH

4P

C2014 100p CH

XX

2.4

CN2001

C2006 0.0047u B

C2019

EXT_IN_L

B

100p CH

C2018

R2012 2200

15

R2036 11k ± 0.5%

C2044 0.1u B

R2038 5600 ± 0.5%

R2019 9.1k

14

(Note) Resistor is mounted the rocation where FB2061 is printed.

VDR201

C2021 0.1u B

R2011 2200

1.5

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

13

SHOE_MIC_L

R2037 11k ± 0.5% 1005

C2029 0.0033u B

R2024 0

12

0uH

C2023 0.068u B 1608

R2013 6800

MIC901 MIC UNIT

C2028 0.015u B

R2023 27k

11

D2062 01ZA8.2(TPL3)

R2008 33k

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

1.5

R2007 18k

MIC AMP

A

10

0uH

6

FB2062

5

FB2063

4

0uH

3

FB2064

2

1

R2074 1k 7.9

Q2073 UN9211J-(TX).SO 0.1 0.1

C2073 0.1u B

4-106

AUDIO I/O MA-385

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

For Schematic Diagram • Refer to page 4-111 for printed wiring board. • Refer to page 4-115 for waveforms. 2 3 1 DD-137 BOARD(1/2) A

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

DC/DC CONVERTER -REF.NO.:10000 SERIESXX MARK:NO MOUNT

BATT/XEXT_SW BATT_SIG

F1605 1.4A 1608

D1602 01ZA8.2(TPL3)

R1604 10 1/8W 3216

3P

BATT_UNREG

R1608 XX 3216

1

BATT_SIG

2

BATT_GND

3

Q1602 SI4963DY-T1 SWITCH 4

C

VTR_UNREG

LF1601 1-411-957-21

D

LND161

A

LND162

A

3

7.9

7.7

6 5 7 8

1

7.7

2

D1601 MA8120-TX

R1602 470k

7.5

7.5 7.5

CAP_ERROR

F1604 1.4A 1608

R1605 1k

2

F1603 1.4A 1608

CAP_VS

F1602 1.4A 1608

D1609 1SS388(TPL3)

0.1

0.8

7.9

C1608 10u 16V TA B

R1606 4700 0

C1616 22u 16V TA B

D1607 RB501V-40TE-17

4

3

Q1603,1604 CHARGE ON SWITCH

R1603 1M

VCC(C)

DRUM_ERROR

6

C1624 4.7u 6.3V B 2012

7

R1641 1k 7.9

VDD C1622 1u B 10V 2012

0.2

R1642 1k

7.9

SI2304DS-T1

2.5

C1626 1u B 10V 2012

Q1612 CPH6702-TL

0

C1635 4.7u 10V B 3216

2.8

C1603 0.022u B

J

3.0 0 0

C1615 0.001u B

0.2

0.3

0.5

11.8 OUT7-2

VCC(O) 5678

-IN8

out8

7.9

6.6 FB8

6.6

2.5

0.7 ROFS

DTC 8

COMP

+IN8

2.5

2.5

1.3

1.2 -IN7

+IN7

FB7

RB8

VDD(O) 567

6

-IN5

OUT5-2 out5-1

7

IC1601 MB4488PFV-BND-G-ER-F

FB5

VSS(O) 567

DTC 56

out4

8

GND

VCC(O) 1234

9

VREF

out3-2

VCC

out3-1

10

CTL1-6,8 CTL7

GND(O) 1234 out2-2

11

CS1-7

out2-1 VDD(O) 123

CSCP

RT

VB

C1604 0.022u B

2.7 Q1623 SI2304DS-T1

10.0

Q1617 2SB1462J-QR(K8).SO 5.0

R1645 47k 6.8

R1637 100

3.0

Q1615 2SD2216J-QR(K8).SO

R1638 100

11.3

2.4 2.4

4.9

R1646 10k

C1629 3300p B

2.9

R1678 1200 ± 0.5%

5.0

2.9

3.9

Q1624 2SD2216J-QR(K8).SO

6.6

R1639 100

9.8

7.9

C1631 3300p B

0.1 T1602

11.8 C1630 3300p B

3.3

4

C1632 3300p B

2.7

3 CH-4

R1640 100

4.9

6

0.1 Q1608 MCH6103-TL SWITCHING 7

2

C1638 0.01u B 1608 25V

R1616 10k ± 0.5%

D1612 1SS388(TPL3)

1.6

8.7

6.6

C1671 R1651 XX 0 13.3V C1649 2.2u 16V 2012 F C1647 2.2u 16V 2012 F

TRV6/6E/11/11E MODEL

PANEL_13.3V

C1650 0.1u 50V 2012 F

D

13

12

D1613 1SS388(TPL3)

C1627 3300p B

8

1

D1610 1SS388(TPL3)

C TRV20/20E MODEL

E

14

C1625 2200p B

C1620 220p B R1626 33k

Q1609 CPH6702-TL 4.7 L1603 22uH CHOKE

R1634 3900 ± 0.5% C1633 4.7u 10V B 3216

R1635 3900 ± 0.5% R1636 ± 0.5%

R1636 10k :TRV20/20E MODEL 15k :TRV6/6E/11/11E MODEL

4.7 1.6 7.9 9.0

R1631 ± 0.5%

R1633 3300 ± 0.5%

*

1.4

1.3

1.3 C1618 470p B R1623 22k

1.2

R1627 22k ± 0.5% R1622 R1624 47k 47k ± 0.5% ± 0.5%

R1681 XX 15V/13.3V

C1646 2.2u F 16V 2012

9.8

R1628 56k ± 0.5%

47k R1612 22k ± 0.5%

M

TO(2/2)

R1679 0

D1611 MA796-TX 5

R1644 100

10.4

R1630 22k ± 0.5%

R1620

C1607 0.1u 10V B

3

R1648 33k ± 0.5%

R1643 100

10.3

R1629 56k ± 0.5%

Drum servo (speed and phase)

C1639 10u 10V TA A

220 R1632

PB

Capstan servo (speed and phase)

Q1615-1617 Q1624 +4.9V REG

R1647 22k ± 0.5%

7.3

9.9

*

REC/PB

1.2 C1617 2200p B R1621 10k

R1615 10k

REC

1.3

2.5

1.6

1.3

1.3 B

0.5

0.5

C1612 2200p

2.0

C1609 100p CH

SIGNAL PATH

L

A

MT_4.9V

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

K

Q1614 Q1623 SWITCHING

MT_4.9V 8.0

9.8

3.0 * R1609 0

out6-1

DC/DC CONVETER

2.8V C1644 4.7u 6.3V B 2012

CHOKE

7.8

C1628 3300p B

OUT6-2

5

IC1601

-IN5(C) +IN5

2.8V L1606 22uH

2.9

Q1616 2SB1581-T1

TRV11/11E/20/20E MODEL

3 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

7.9 C1602 0.1u B

4

out1-2

2.5

2.9

B

2

OUT7-1

-IN6 FB6

Q1622 SI2304DS-T1

10.5

Q1613 Q1622 SWITCHING

2.8 1

out1-1

TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV11 MODEL :DCR-TRV11 TRV11E MODEL:DCR-TRV11E TRV20 MODEL :DCR-TRV20 TRV20E MODEL:DCR-TRV20E

2.5

C1674 0.01u B

2

VSS(O) 1234

1.2 R1702 1k

3

FB1

I

4

-IN1

0.9

5

-IN2

0.9

6

FB2

1.8

7

FB3

1.1

-IN3

0.3

8

GND(O) 5678

DTC 123

R1699 22k

9

1

DTC4

R1700 22k

3.3

Q1614 CPH6702-TL

-IN6(C)

-IN4

R1701 22k

1.9V C1643 4.7u 6.3V B 2012

CHOKE

7.9

C1637 4.7u 10V B 3216

+IN6

FB4

0.3

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17

0.5 C1605 2200p B R1610 4700

DTC 7

OVP 56

R1696 47k

H

CT

R1697 22k

16 15 14 13 12 11 10

TRV11/11E/20/20E MODEL

D_1.9V L1605 22uH

2.0

CH-2

2.5

2.5 R1695 270k

2.0

Q1612 Q1621 SWITCHING

C1621 100p CH

C1619 0.001u B

C1611 470p B

C1642 4.7u 6.3V B 2012

Q1621 SI2304DS-T1

10.1

CH-3

-IN8’

G

3.1V

L1604 22uH CHOKE

7.9 CH-7

C1636 4.7u 10V B 3216

R1614 22k

3.1V

3.2 3.2

Q1607 UN9213J-(K8).SO

R1619 3300 ± 0.5%

R1611 22k

Q1611 Q1620 SWITCHING

Q1620

10.2

CH-5

Q1613 CPH6702-TL

TRV11/11E/20/20E MODEL

C1641 4.7u 6.3V B 2012

CHOKE

2.9

Q1606,1607 PROTECT DETECT

R1625 10k

L1602 33uH

2.7

8CH

R1617 68k ± 0.5%

DRUM VS

2.7

9.2

0

D1608 VSS RB501V-40TE-17

D1606 RB501V-40TE-17

R1613 47k ± 0.5%

Q1619 SI2304DS-T1

8

1

F

CHOKE

11.3

Q1611 CPH6702-TL

DRUM_VS

C1640 4.7u 6.3V B 2012

7.9 CH-6

C1623 4.7u 6.3V B 2012

7.8

Q1605 MCH6202-TL SWITCHING

R1698 22k

CAP VS

3.9

5

TRV11/11E/20/20E MODEL

C1606 XX B 2012

3.0

C1614 22u 16V TA B

C1613 10u 16V TA B

C1610 10u 16V TA B

T1601

C1634 4.7u 10V B 3216

Q1618 SI2304DS-T1

4.6V C1645 4.7u 6.3V B 2012

CH-1 Q1609,1618 SWITCHING

R1631 82k :TRV6/6E/11/11E MODEL 100k :TRV20/20E MODEL

R1618 27k

16

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

DC/DC CONVERTER DD-137 (1/2)

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

4-107

TO(2/2)

L1601 22uH

0.8

Q1601 SSM3K03FE(TPL3) SWITCH

E

Q1610 Q1619 SWITCHING

F1601 1.4A 1608

2 C1601 0.022u B 16V

Q1610 CPH6702-TL

7.9

Q1606 2SB1462J-QR(K8).SO

3

7.3

2

F1606 1.4A 1608

Q1603 2SB1122-ST-TD

ACV_GND BATT_XEXT

R1607 XX 3216

Q1604 UN9213J-(K8).SO

1

CN1602

TO(2/2)

BATT_UNREG

ACV_UNREG

D1604 1SS388(TPL3)

J902 DC IN

J901 BATTERY TERMINAL

INIT_CHARGE_ON

3P

CN1601

B

1

FAST_CHARGE

R1601 1k

VTR_DD_ON REG_GND

4-108

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

For Schematic Diagram • Refer to page 4-111 for printed wiring board. 2 3 1

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

DD-137 BOARD(2/2) DC/DC CONVERTER

A

NO MARK:REC/PB MODE R :REC MODE P :PB MODE

-REF.NO.:10000 SERIESXX MARK:NO MOUNT

TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV11 MODEL :DCR-TRV11 TRV11E MODEL:DCR-TRV11E TRV20 MODEL :DCR-TRV20 TRV20E MODEL:DCR-TRV20E

CAP_ERROR

2 TO(1/2)

B

CAP_VS DRUM_ERROR DRUM_VS C1670 XX B 2012

Q1627 2SA2018-H-T2L

C

1.5 C1660 10u 6.3V A

2.0

R1652 100k

IC1602 4.7

0.7 IC1602 TA75S01F(TE85R)

R1657 33k ± 0.5%

DIGITAL 3.1V ANALOG 3.1V

3.1V

L1608 1uH 3225

D 1.9V

1.3 5

4

+

–

0.7

1

2

C1665 XX B

3

0.1

* L1607 3225

Q1628 2SD2216J-QR(K8).SO

1.3

ERROR AMP

* L1619

D1615 MA3XD21001S0

COM G R B BLK

*

*

1.5 C1658 6.3V A

C1652 6.3V A

1.5

C1651 10u :TRV6/6E/11/11E MODEL 47u:TRV11/11E MODEL

C1651 6.3V A

R1656 22k

R1658 110k ± 0.5%

C1663 0.1u B

HCK1 R1655 470

HCK2 HST RGT

L1610 1uH 3225 L1612 4.7uH L1611 1uH 3225

E

ANALOG 2.8V

DCG/CLR

AUDIO 2.8V

EN

DIGITAL 2.8V

STB VCK2

2.8V

Q1639 2SD2216J-QR(K8).SO -7.7

R4.5/ P-1.8

R1654 22k

R-9.1/ P-9.6

*

R1690 ± 0.5%

* Q1647

* Q1653

* R1676

-7.7

DET

± 0.5% 0.1

0.5 R1666 22k

* R1680 R1677 220k ± 0.5%

0.5

* Q1649

C1669 B

C1672 4.7u 25V TA B

R1691 ± 0.5%

LED_K PWM

R1689 ± 0.5%

R1686

*

2.5

B

Q1635 2SB1462J-QR(K8).SO

Q1629 UN9213J-(K8).SO

R1653 47k

C1666 10u 20V B TA

*

A

Q1650

R1684

R1675 100k ± 0.5%

R-9.1/ P-9.6

R1662 100k

*

R9.7/P-10.2

G

* L1624 *

C1654 10u :TRV20/20E MODEL 22u:TRV6/6E/11/11E MODEL

F

VST

C1659 47u 6.3V B

C1656 10u 6.3V A

C1654 6.3V A

*

C1653 10u 6.3V A

*

L1609 4.7uH 3225

27P

CN1604 Q1627 Q1628 +1.5G REG

27

COM

26

G

25

R

24

B

23

BLK

22

HCK1

21

HCK2

20

HST

19

RGT

18

DCG/CLR

17

EN

16

STB

TO LB-64 BOARD CN2201 THROUGH THE FP-180 FLEXIBLE BOARD

15

VCK2

14

VST

13

VSS

12

VSS

11

VDD

10

EVF_BL_GND

9

EVF_BL_GND

8

EVF_BL_4.6V

7

EVF_BL_4.6V

6

N.C(XTALLY_LED)

5

DET

4

LED_K

3

PWM

2

N.C

1

N.C

(SEE PAGE 4-86)

Q1643 2SB1462J-QR(K8).SO

C

*MARKED:MOUNT TABLE TRV20/20E MODEL

TRV11/11E MODEL

C1652

10u 6.3V

10u 6.3V

XX

C1658

10u 6.3V

10u 6.3V

XX

C1669

XX

0.1u 10V B

0.1u 10V B

L1607

1uH ± 20%

1uH ± 20%

XX

L1619

4.7uH ± 20%

4.7uH ± 20%

XX

L1624

4.7uH ± 20%

XX

XX

Q1646

UN9213J

XX

XX

Q1647

XX

2SD2216J

2SD2216J

Q1648

UN9213J

XX

XX

Q1649

XX

2SD2216J

2SD2216J

MT_4.9V R1669 0

* R1692

Q1637 2SD2216J-QR(K8).SO

* R1683

D

R-27.8/P-23.4 R-27.8/P-23.4

-16.0

R1672 47k ± 0.5%

Q1632,1637 Q1641 -15.3VG REG

TO(1/2)

0.5 R1664 22k

R1674 100k ± 0.5%

*

*

* R1685 C1667 2.2u F 2012 16V

VST

* Q1648

INV.

L1618 22uH

Q1625,1626 SHOE ON SWITCH 7.9

INV.

L1617 22uH 3225

R1649 10k

Q1626 MGSF3455VT1 0

C1648 1u 10V B 2012

R1663 XX

Q1634 XX

C1655 2.2u 16V F 2012

R1682 1k

R1665 XX D1616 MA2S111-(K8).SO

0.1

R1667 XX ± 0.5% C1668 2.2u F 16V 2012

R1670 XX ± 0.5%

EVF_STB

EVF_G

4

EVF_VCK2

EVF_R

6

7

EVF_VST

EVF_B

8

3 5

9

EVF_GND

EVF_BLK

10

11

EVF_VCC

EVF_HCK1

12

13

EVF_DET

EVF_HCK2

14

15

EVF_LED_K

EVF_HST

16

17

EVF_PWM

EVF_RGT

18

19

EVF_13.3V

EVF_DCG/CLR

20

21

EVF_2.8V

EVF_BL-

22

PANEL_-15.3V

27

SHOE_ON

4.6V

EVF_BL+

24

PANEL_13.3V

26

PANEL_4.6V

28

SHOE_GND

SHOE_UNEREG

30

31

SHOE_GND

SHOE_UNEREG

32

33

REG_GND

CAM_-7.5V

34

COM G R B BLK HCK1 HCK2 HST RGT DCG/CLR

35

REG_GND

CAM_15V

36

37

REG_GND

D_3.1V

38

39

REG_GND

D_3.1V

40

A_3.1V

RP_4.6V AU_4.6V

A_4.6V

44

45

A_2.8V

A_4.6V

46

47

A_2.8V

AU_2.8V

48

43

A_4.6V

49

D_2.8V

D_1.9V

50

51

D_2.8V

D_1.9V

52

53

MT_4.9V

D_1.5V

54

55

MT_4.9V

D_1.5V

56

57

MT_4.9V

DRUM_VS

58

59

MT_GND

DRUM_VS

60

61

MT_GND

DRUM_ERROR

62

63

MT_GND

CAP_VS

64

65

VTR_DD_ON

CAP_VS

66

67

CAM_DD_ON

CAP_ERROR

68

69

INIT_CHARGE_ON

VTR_UNREG

70

71

FAST_CHARGE

VTR_UNREG

72

73

BATT_SIG

VTR_UNREG

74

75

BATT/XEXT_SW

BATT_UNREG

76

77

P_UNREG_GND

P_UNREG

78

79

P_UNREG_GND

P_UNREG

80

AU_4.6V R1693 1 2012

EVF_BL_4.6V

L

1 C1657 10u 10V TA A

C1661 10u 10V TA A

C1664 10u 10V TA A

XX

2S81462J

2S81462J

Q1653

XX

2SD2216J

2SD2216J

R1609

0

0

XX

R1631

100k

82k

82k

R1636

10k

15k

15k

C1662 10u 10V TA A

R1694 2012 C1673 10u 10V TA A

VTR_DD_ON

XX

0

0

R1669

0

XX

XX

R1676

10k

22k

18k

47k

R1680

XX

R1683

820

XX

XX

R1684

XX

100k

100k

R1685

22k

XX

XX

R1686

XX

22k

22k

R1687

1800

XX

XX

R1688

1800

XX

R1689

XX

18k

18k

R1690

XX

100k

100k

R1691

XX

47k

47k

R1692

820

XX

XX

42

RP_4.6V

L1614 1uH 2520

Q1650

R1668

L1615 1uH 2520 L1616 1uH 2520

PANEL_2.8V

25

41

L1613 4.7uH

M

PWM

2

EVF_EN

29

R1671 XX ± 0.5%

D1614 MA2S111-(K8).SO

Q1625 UN9213J-(K8).SO 7.9

R1650 1M

4.6V

DET

80P EVF_COM

1

23 Q1636 XX

7.7

K

STB VCK2

Q1633 XX

J

R15.2/P0.1

R3.0/ P0.1

LED_K

PANEL_13.3V

E

CN1603

R1688 EN

R0/ P2.1

R0/P2.1

* Q1646

Q1641 2SB1462J-QR(K8).SO

3

I

R0/ P0.1

-0.2

Q1632 2SB1462J-QR(K8).SO

R1687

R1668

*

H

R1673 270k ± 0.5%

-16.0

R-28.3/ P-23.9

R1661 100k

TRV6/6E MODEL

47k

XX

REG GND

REG_GND INIT_CHARGE_ON

1 TO(1/2)

SIGNAL PATH

TO VC-240 BOARD CN002

FAST_CHARGE

(SEE PAGE 4-66)

BATT_SIG

REC

BATT/XEXT_SW BATT_UNREG

REC/PB

PB

Drum servo (speed and phase)

VTR_UNREG

N

Capstan servo (speed and phase) 16

4-109

4-110

DC/DC CONVERTER DD-137 (2/2)

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

DD-137 (DC/DC CONVERTER) PRINTED WIRING BOARD — Ref. No. DD-137 Board; 10,000 Series —

1-677-550-

For printed wiring board • Refer to page 4-127 for parts location. • This board is four-layer print board. However, the patterns of layers two to four have not been included in the diagram. • Chip parts

LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER) DD-137 (DC/DC CONVERTER)

Transistor C

B

E

65 4

45 6

12 3

32 1

JK-188 (AV IN/OUT)

PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)

There are few cases that the part printed on this diagram isn’t mounted in this model.

DC/DC CONVERTER DD-137

4-111

INVERTER TRANSFORMER UNIT

4-112

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

4-3. WAVEFORMS

PD-123 BOARD (1/2)

FP-219 BOARD

CD-252 BOARD CAMERA REC

REC/PB

1 IC3000 1

1 IC2171 2

1 Q102 E 7.5Vp-p 64 µsec

3.0Vp-p 1.0Vp-p

38.5 µsec

43.3 µsec

2 IC3000 2 2 IC104 qa 19.8Vp-p 1.0Vp-p

20 msec

43.3 µsec

3 IC3000 3,4 3 IC104 qd 7.3Vp-p

64 µsec 3.6Vp-p 30 nsec

4 IC3000 0 4 IC104 qf

3.5Vp-p 55.5 nsec 3.6Vp-p 30 nsec

5 IC3000 qa,qs

5 IC104 5

900mVp-p 43.3 µsec

3.3Vp-p 55.5 nsec

6 IC3000 qd 6 IC102 wl 16.4Vp-p 64 µsec 3.1Vp-p 15 nsec

7 Q3000 E

0.8Vp-p 64 µsec

4-113

WAVEFORMS CD-252, FP-219, PD-123

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

PD-123 BOARD (2/2)

PD-124 BOARD (1/2)

REC/PB

REC/PB

2 IC2104 rh

0 IC2105 qg

1 IC3171 2

3.1Vp-p 500mVp-p H

3 IC2104 rj

3.0Vp-p

H

38.5 µsec

qa IC2105 qk

3.0Vp-p 440mVp-p

V

H

PD-124 BOARD (2/2) REC/PB

4 IC2104 rk

2 IC3101 rh

qs IC2105 wa

420mVp-p H

3.0Vp-p

7 IC3101 wf

500mVp-p

H

H

8.0Vp-p 2H

5 IC2104 w;

3 IC3101 rj

qd IC2105 wd

3.0Vp-p

4.0Vp-p

440mVp-p

90 nsec 2H

8 IC3102 1

H

H

3.5Vp-p

6 IC2104 ws

4 IC3101 rk

qf IC2105 wf

2.8Vp-p 3.5Vp-p

9 IC3102 wh

420mVp-p

127 µsec

3.0Vp-p

H 55 nsec

2H

7 IC2104 wf

5 IC3101 w;

qg IC2105 wh

0 IC3102 rk

3.0Vp-p V

3.2Vp-p 2H

8 IC2105 1

8.0Vp-p

45 nsec

3.5Vp-p

2H

6 IC3101 ws

qh IC2105 rk

3.0Vp-p

3.0Vp-p V

H

8.0Vp-p 2H

9 IC2105 qf

3.2Vp-p H

WAVEFORMS PD-123, PD-124

4-114

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

DD-137 BOARD (1/2) REC/PB

1 IC1601 3

8 IC1601 th

5.1Vp-p 1.3Vp-p 2.4 µsec

2 IC1601 1

2.4 µsec

9 IC1601 tf

5.0Vp-p 2.5 µsec

5.0Vp-p 2.4 µsec

3 IC1601 yf

0 IC1601 td

5.1Vp-p

5.1Vp-p 2.4 µsec

2.4 µsec

4 IC1601 ys

qa IC1601 ta

5.0Vp-p

5.0Vp-p 2.4 µsec

2.4 µsec

5 IC1601 ya

qs IC1601 t;

5.1Vp-p 2.4 µsec

5.1Vp-p 2.4 µsec

6 IC1601 tl

qd IC1601 rj

5.2Vp-p 5.0Vp-p 2.6 µsec

7 IC1601 tk

2.6 µsec

2.5 µsec

qf IC1601 rk

5.0Vp-p 5.0Vp-p 2.5 µsec

4-115

WAVEFORMS DD-137

Waveforms and parts location of the VC-240/241 board are not shown. Pages from 4-116 to 4-123 are not shown.

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

4-4. MOUNTED PARTS LOCATION NS-10 BOARD (SIDE A)

CD-252 BOARD (SIDE A)

CK-92 BOARD (SIDE A)

CK-94 BOARD (SIDE A)

R001

A-1

CN3202 B-2

CN3202 B-2

S001

A-1

C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C114 C116 C118 C119 C120 C122 C124 C125 C126 C127 C128 C129 C130 C131 C132 C151 C152

C-5 C-5 D-5 C-5 C-5 C-6 C-5 C-5 C-5 D-5 D-6 D-6 C-4 C-7 B-6 B-5 C-7 B-6 B-5 C-6 D-6 C-6 C-6 B-5 B-5 B-5 B-5 C-5 E-1 E-1

CN151 E-1 CN152 E-1 D101

D-5

FB101 FB102 FB103 FB104 FB105 FB106 FB108 FB109

D-5 D-5 C-6 C-6 C-6 B-4 C-5 D-6

IC102 IC103 IC104

C-5 C-6 B-5

L101 L103 L104 L105 L151

C-5 C-6 C-6 B-5 E-1

Q101 Q102 Q103 Q104

C-6 C-5 C-4 C-4

R102 R104 R105 R106 R107 R108 R109 R112 R113 R114 R122 R123 R151

D-6 C-6 C-6 C-6 D-5 C-6 D-6 C-4 B-6 C-4 C-5 B-6 E-1

X101

D-5

R3202 R3205 R3206 R3207 R3208 R3209 R3210 R3211 R3212 R3213 R3214 R3215 R3216

E-6 D-6 A-5 E-5 D-6 C-5 B-5 D-6 C-5 C-6 E-7 B-5 C-6

S3201 S3202

B-1 A-1

S3203 S3204 S3205 S3206 S3207 S3208 S3209 S3210 S3211 S3212 S3213 S3214 S3215 S3216 S3217 S3218

E-6 A-2 E-5 D-6 C-5 B-6 D-5 C-6 D-7 D-7 B-5 D-6 E-7 C-7 D-5 B-5

R3202 R3205 R3206 R3207 R3208 R3209 R3210 R3211 R3212 R3213 R3214 R3215 R3216

E-6 D-6 B-5 E-5 D-6 C-5 B-5 D-6 C-5 C-6 E-7 B-5 C-6

S3201 S3202

B-1 A-1

S3203 S3204 S3205 S3206 S3207 S3208 S3209 S3210 S3211 S3212 S3213 S3214 S3215 S3216 S3217 S3218

E-6 A-1 E-5 D-6 C-5 B-6 D-5 C-6 D-7 D-7 B-5 D-6 E-7 C-7 D-5 B-5

CK-92 BOARD (SIDE B)

CK-94 BOARD (SIDE B)

BT3201 D-10

BT3201 C-10

C3201 C3202 C3203

B-13 B-14 B-13

CN3201 CN3203 CN3204 CN3205 CN3206

B-13 B-10 E-10 B-12 B-11

D3201 D3202 D3203 D3204

B-10 B-10 B-10 B-10

R3201 R3203 R3204 R3217

B-13 A-14 E-10 B-10

C3201 C3202 C3203

B-13 B-14 B-13

CN3201 CN3203 CN3204 CN3205 CN3206

B-13 B-10 E-10 B-11 B-11

D3201 D3202 D3203 D3204

B-10 B-10 B-10 B-10

R3201 R3203 R3204 R3217

B-13 A-14 E-10 B-10

CD-252 BOARD (SIDE B) CN101 A-11 IC101

C-10

4-125

LOCATION NS-10, CD-253, FP-219, CK-92, CK-94

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

LB-64 BOARD (SIDE A)

JK-188 BOARD (SIDE A)

PD-123 BOARD (SIDE A)

PD-124 BOARD (SIDE A)

C2201

C3063 C3064 C3066 C3067

E-3 D-3 E-3 E-3

J3001 J3002 J3003 J3004

C-5 D-4 E-4 F-4

L3052

E-3

C2101 C2102 C2103 C2104 C2105 C2106 C2107 C2108 C2109 C2110 C2111 C2112 C2113 C2114 C2115 C2116 C2117 C2118 C2119 C2120 C2121 C2122 C2123 C2124 C2125 C2127 C2128 C2129 C2130 C2131 C2132 C2133 C2134 C2135 C2172 C2173 C2174 C2175 C2180 C2182

B-1 A-1 A-2 A-2 A-2 B-2 B-2 C-2 B-2 B-2 C-2 B-1 B-2 B-2 B-1 C-2 B-3 C-3 B-2 B-2 B-2 B-3 C-3 C-4 A-3 B-3 B-3 B-1 A-4 B-9 A-3 A-2 A-2 A-2 C-3 C-4 C-3 C-3 B-1 A-1

CN2101 CN2173 CN2174 CN2175 CN2176

B-12 A-3 C-4 C-1 A-2

C3101 C3102 C3103 C3104 C3105 C3106 C3107 C3108 C3109 C3110 C3111 C3112 C3113 C3114 C3115 C3116 C3117 C3118 C3119 C3120 C3121 C3122 C3123 C3124 C3125 C3126 C3127 C3128 C3130 C3131 C3132 C3133 C3134 C3135 C3136 C3137 C3171 C3173 C3174 C3175 C3176 C3177

D-2 D-1 D-1 B-1 D-1 C-2 C-1 C-1 C-1 C-1 C-2 C-2 B-2 D-2 C-2 D-2 B-3 D-2 C-2 C-2 C-2 C-2 C-3 C-3 C-3 B-1 C-3 B-3 B-2 B-2 B-3 C-1 C-1 C-1 B-2 B-1 D-2 B-3 B-3 B-3 B-3 D-1

D2101 D2102 D2103

B-2 B-3 B-10

CN1374 CN3101 CN3171 CN3172 CN3173

A-3 A-2 C-1 B-1 D-3

IC2104 IC2105 IC2106 IC2171

B-2 B-3 C-3 C-1

D3101 D3102 D3103 D3104 D3105

B-3 B-3 B-2 B-3 B-3

L2101 L2102 L2103 L2104 L2105 L2172 L2173

B-1 C-2 C-2 C-2 B-3 C-3 C-2

C-1

CN2201 C-1 D2202

A-1

IC2201 C-1 L2201 L2202

C-2 C-2

ND2201 A-1 Q2201

C-1

SE3051 C-3 SE3052 D-2

R2202 R2205

C-2 C-1

JK-188 BOARD (SIDE B)

LB-64 BOARD (SIDE B) C2202 C2203 C2204

C-3 C-3 C-3

CN2202 C-3 R2203 R2204

C-4 C-4

T2201

A-3

C3051 C3052 C3053 C3054 C3055 C3056 C3057 C3058 C3059 C3060 C3061 C3062 C3065

C-10 C-10 C-9 E-9 D-10 C-10 D-10 D-10 D-10 D-9 D-10 D-10 D-9

CN3001 A-11 D3001

C-7

FB3004 FB3005 FB3007 FB3008

F-9 E-8 D-9 D-9

IC3051 E-10

LOCATION LB-64, JK-188, PD-123, PD-124

R3001 R3002 R3003 R3004 R3005 R3051 R3052 R3053 R3054 R3055 R3056 R3057 R3058 R3059 R3060 R3061

C-8 B-8 C-8 E-9 D-8 D-10 C-10 C-10 D-10 E-10 E-9 E-10 E-9 E-9 E-10 C-10

VDR001 VDR002 VDR003 VDR004 VDR005 VDR006 VDR007

F-9 E-8 D-8 D-9 C-8 C-8 E-9

4-126

Q2102 Q2103 Q2104 Q2105 Q2106 Q2107 Q2108 Q2172 Q2173

C-3 B-3 B-3 B-3 A-3 B-2 A-3 C-3 C-3

R2101 R2103 R2105 R2106 R2107 R2108 R2109 R2111 R2112 R2113 R2114 R2116 R2117 R2118 R2119 R2120 R2121 R2122 R2123 R2124 R2125 R2126 R2127 R2129 R2133 R2134 R2135 R2140 R2141 R2142 R2143 R2144 R2145 R2146 R2147 R2148 R2149 R2150 R2151 R2152 R2153 R2154 R2175 R2176 R2177 R2178 R2180

A-3 B-3 A-1 A-2 A-2 A-2 A-2 B-2 B-1 B-2 B-2 B-2 B-2 B-2 B-2 B-3 B-3 B-5 A-3 B-8 B-3 B-4 B-3 B-3 B-7 B-6 C-4 B-3 A-3 B-2 A-1 C-3 C-3 A-4 B-3 B-3 A-3 A-3 B-11 A-2 A-2 A-2 C-3 C-3 A-1 A-1 B-1

IC3101 C-2 IC3102 B-2 IC3171 D-3 L3101 L3102 L3103 L3104 L3171 L3172

C-3 D-1 C-1 B-2 B-3 B-3

Q3102 Q3103 Q3104 Q3105 Q3106

C-3 C-3 B-1 B-1 A-2

Q3107 Q3108 Q3109 Q3110 Q3171 Q3172

B-2 B-1 B-2 B-3 C-3 B-3

R3101 R3102 R3104 R3105 R3106 R3107 R3108 R3109 R3110 R3111 R3112 R3113 R3114 R3115 R3116 R3117 R3118 R3119 R3120 R3121 R3122 R3123 R3124 R3125 R3126 R3127 R3128 R3131 R3132 R3133 R3135 R3136 R3137 R3138 R3139 R3140 R3141 R3142 R3143 R3144 R3146 R3147 R3148 R3149 R3150 R3151 R3151 R3152 R3153 R3154 R3155 R3156 R3157 R3158 R3159 R3160 R3171 R3172 R3173 R3174 R3175 R3176 R3177 R3178

C-1 D-1 C-1 C-1 C-2 B-3 D-2 C-2 C-2 C-2 C-2 B-3 C-2 B-3 C-2 C-2 C-2 C-2 C-2 C-3 C-3 C-3 D-2 C-3 C-3 B-2 B-2 B-1 B-2 A-2 C-2 A-3 C-3 A-2 B-1 C-1 C-1 C-1 B-3 A-2 C-3 B-1 B-2 A-2 B-2 B-2 B-2 A-3 A-3 A-2 B-3 B-2 C-3 C-3 C-3 C-2 B-1 A-1 A-1 D-2 C-3 C-3 D-1 D-1

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

SE-107 BOARD (SIDE A)

MA-385 BOARD (SIDE A)

DD-137 BOARD (SIDE A)

DD-137 BOARD (SIDE B)

PH081 C-1 PH082 C-2

C2005 C2006 C2007 C2009 C2011 C2014 C2015 C2017 C2018 C2019 C2020 C2021 C2022 C2024 C2025 C2026 C2030 C2031 C2032 C2034 C2042 C2043 C2071 C2091 C2103 C2106

E-2 E-3 E-3 D-2 E-2 E-3 E-3 E-2 E-3 E-3 E-2 D-3 D-2 D-3 E-2 D-2 D-2 D-2 D-2 D-2 E-1 D-3 B-2 D-4 E-2 E-2

C1639 C1648 C1651 C1652 C1653 C1654 C1656 C1657 C1658 C1659 C1660 C1661 C1662 C1663 C1664 C1665 C1666 C1667 C1669 C1672 C1673

D2001 D2061 D2062 D2063 D2071 D2072

E-2 D-4 E-2 E-1 A-2 A-3

FB2001 FB2002 FB2061 FB2062 FB2063 FB2064

E-1 E-2 E-1 E-1 E-1 E-1

C1601 C1602 C1603 C1604 C1605 C1606 C1607 C1608 C1609 C1610 C1611 C1612 C1613 C1614 C1615 C1616 C1617 C1618 C1619 C1620 C1621 C1622 C1623 C1624 C1625 C1626 C1627 C1628 C1629 C1630 C1631 C1632 C1633 C1634 C1635 C1636 C1637 C1638 C1640 C1641 C1642 C1643 C1644 C1645 C1646 C1647 C1649 C1650 C1655 C1668 C1670 C1671 C1674

IC2002 D-3 IC2091 D-4 Q2071 Q2072 Q2073 Q2074

B-2 A-2 B-2 A-2

R2007 R2008 R2011 R2012 R2013 R2014 R2015 R2016 R2018 R2021 R2022 R2025 R2026 R2028 R2029 R2035 R2061 R2062 R2063 R2064 R2065 R2071 R2072 R2073 R2074 R2075 R2091

E-2 E-2 E-3 E-2 D-3 E-2 D-2 D-3 D-2 D-2 D-2 E-2 D-2 D-2 D-2 D-3 D-4 E-3 E-3 E-3 D-3 B-2 B-2 A-2 B-2 A-2 D-4

S2061

E-4

VDR201 E-1

MA-385 BOARD (SIDE B) C2008 C2010 C2012 C2023 C2027 C2028 C2029 C2033 C2035 C2036 C2037 C2038 C2039 C2041 C2044 C2045 C2046 C2047 C2072 C2073

E-8 E-7 E-8 D-6 D-6 D-6 D-7 D-7 D-7 D-8 D-8 D-8 D-7 D-8 E-8 E-8 E-8 E-8 A-7 B-8

R2009 R2010 R2017 R2019 R2020 R2023 R2024 R2027 R2030 R2031 R2032 R2033 R2034 R2036 R2037 R2038 R2039 R2051 R2052

D-7 E-8 D-6 D-6 D-6 D-6 D-6 D-7 D-7 D-8 D-7 D-8 D-8 E-8 E-8 E-8 E-8 D-7 D-7

A-1 A-2 A-3 A-5 A-4 A-4 B-4 B-5 A-5 B-4 B-4 B-5 A-5 B-4 B-5 B-4 B-3 B-3 B-3 B-4 B-5

CN1601 B-1 CN1602 B-1 CN1604 B-4 D1602 D1614 D1615 D1616

B-1 A-1 A-4 A-1

F1601 F1602 F1603 F1604 F1605 F1606

B-1 B-1 B-2 B-2 B-2 B-1

IC1602 B-4 L1601 L1602 L1603 L1604 L1605 L1606 L1607 L1608 L1609 L1610 L1611 L1612 L1613 L1614 L1615 L1616 L1619 L1624

A-2 A-2 B-2 A-2 B-2 A-3 A-5 A-4 A-4 B-4 A-4 B-4 B-5 B-5 B-5 B-5 A-4 B-3

LF1601 B-1 Q1615 Q1617 Q1624

CN2001 D-7 CN2051 E-7 CN2071 B-8

A-1 A-1 A-2

Q1625 Q1626 Q1627 Q1628 Q1629 Q1632 Q1635 Q1637 Q1639 Q1641 Q1643 Q1646 Q1647 Q1648 Q1649 Q1650 Q1653

A-1 A-1 B-4 B-4 B-3 B-3 B-3 B-3 B-3 B-3 B-3 B-4 B-4 B-3 B-4 B-3 B-4

R1601 R1607 R1608 R1645 R1646 R1647 R1648 R1649 R1650 R1652 R1654 R1655 R1656 R1657 R1658 R1661 R1662 R1664 R1666 R1668 R1669 R1672 R1673 R1674 R1675 R1676 R1677 R1678 R1680 R1682 R1683 R1684 R1685 R1686 R1687 R1688 R1689 R1690 R1691 R1692 R1693 R1694

B-1 B-1 B-1 A-2 A-1 A-2 A-2 A-2 A-1 B-4 B-3 B-4 B-4 B-4 B-4 B-3 B-3 B-3 B-3 B-4 B-3 B-3 B-3 B-3 B-3 B-3 B-3 A-2 B-3 A-1 B-4 B-3 B-4 B-3 B-4 B-4 B-4 B-4 B-4 B-3 B-4 B-5

T1601 T1602

B-2 B-2

B-10 B-7 B-7 B-6 B-7 B-9 B-6 B-9 B-6 B-9 B-7 B-6 B-9 B-9 B-8 A-9 B-6 B-6 B-8 B-6 B-7 B-8 B-8 B-8 B-6 B-8 B-7 B-7 A-7 A-7 A-7 B-7 B-9 A-9 B-9 B-9 A-8 B-9 A-9 B-9 B-8 B-9 B-8 B-9 B-8 B-9 B-9 B-8 B-8 B-8 B-7 B-8 B-7

CN1603 A-7 D1601 D1604 D1606 D1607 D1608 D1609 D1610 D1611 D1612 D1613

B-10 B-10 B-9 B-8 B-8 B-8 B-9 B-8 B-8 B-9

IC1601 B-7

D-8 D-6

L1617 L1618

B-8 B-8

FB2003 E-8

Q1601 Q1602 Q1603 Q1604 Q1605

B-10 B-10 B-10 A-10 B-9

D2002 D2091

J2001 J2002

D-9 E-9

L2001

D-8

4-127E

Q1606 Q1607 Q1608 Q1609 Q1610 Q1611 Q1612 Q1613 Q1614 Q1616 Q1618 Q1619 Q1620 Q1621 Q1622 Q1623 Q1633 Q1634 Q1636

B-8 B-8 B-8 B-9 A-9 A-9 A-9 B-9 A-8 A-10 B-9 A-9 A-9 A-8 B-9 B-8 B-8 B-8 B-8

R1602 R1603 R1604 R1605 R1606 R1609 R1610 R1611 R1612 R1613 R1614 R1615 R1616 R1617 R1618 R1619 R1620 R1621 R1622 R1623 R1624 R1625 R1626 R1627 R1628 R1629 R1630 R1631 R1632 R1633 R1635 R1636 R1637 R1638 R1639 R1640 R1641 R1642 R1643 R1644 R1651 R1663 R1665 R1667 R1670 R1671 R1679 R1681 R1695 R1696 R1697 R1698 R1699 R1700 R1701 R1702

B-10 B-10 B-10 B-10 A-10 B-7 B-7 B-7 B-6 B-8 B-7 B-6 B-6 B-8 B-6 B-8 B-6 B-6 B-6 B-6 B-6 B-7 B-6 B-6 B-6 B-6 B-6 B-6 A-6 B-6 B-6 B-6 A-7 B-7 B-7 A-7 B-8 B-8 B-7 A-7 B-8 B-8 B-8 B-8 B-8 B-8 B-8 B-8 B-7 B-7 B-7 B-7 B-7 B-7 B-7 B-7

LOCATION SE-107, MA-385, DD-137

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E SECTION 5 ADJUSTMENTS 1.

Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.

Procedure 1 Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced. (Machine before starting repair)

PC

PC

(Machine after a board is replaced)

Download the saved data to a machine.

Save the EVR data to a personal computer.

Procedure 2 Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM to the replaced board. Remove the EEPROM and install it.

(Former board)

(New board)

Procedure 3 When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or installed, save the data from the same model of the same destination, and download it. (Machine to be repaired)

PC

(Machine to be repaired)

Download the data. Save the data.

(The same model of the same destination)

After the EVR data is saved and downloaded, check the respective items of the EVR data. (Refer to page 5-3 for the items to be checked.)

5-1

1-1. Adjusting items when replacing main parts and boards. • Adjusting items when replacing main parts (DCR-TRV6/TRV6E/TRV11/TRV11E) When replacing main parts, adjust the items indicated by z in the following table. Note1: When replacing the drum assy., reset the data of page: 2, address: A2 to A4 to “00”. (Refer to “Record of Use check” of “5-4. SERVICE MODE”) Replaced parts

Adjustment Section

Adjustment

Parts replacement

Lens device Mechanism deck Color EVF block LCD902 (LCD panel) LCD block LCD901 (LCD panel) LCD block ND901 (Fluorescent tube) LCD block Inverter unit Control switch block (FK-30150) Mechanism deck M901 (Drum assy) Note1 Mechanism deck M902 (Capstan motor) Mechanism deck LS chassis D3 assy JK-188 board SE3051/3052 (PITCH/YAW sensor) PD-123 board IC2104 (RGB driver (LCD)) *1 PD-123 board IC2105 (Timing generator (LCD)) *1 PD-124 board IC3101 (RGB driver (LCD)) *2 PD-124 board IC3102 (Timing generator (LCD)) *2 LB-64 board ND2201 (Fruorescent tube (EVF)) VC-241 board IC1802 (RGB driver (EVF)) VC-241 board IC1803 (Timing generator (EVF)) FP-219 flexible IC101 (CCD imager) VC-241 board IC702, X701 (Timing generator) VC-241 board IC701 (CDS, AGC, A/D conv.) VC-241 board IC204 (Lens predriver) VC-241 board IC751 (Camera process, EVR) VC-241 board IC1301 (LINE IN/OUT AMP) VC-241 board IC301 (DV signal process) VC-241 board IC101 (EQ, A/D conv., PLL) VC-241 board IC102 (REC/PB AMP) VC-241 board IC1901 (IR transmitter)

Block replacement

Initialization Initialization of C, D, 8 page data of B, C, D, E, Initialization of B page data *1 F, 7, 8 page data Initialization of E, F, 7 page data 36MHz origin oscillation adj. Zoom center adj. z Hall adj. z Flange back adj. z Optical axis adj. z Camera Color reproduction adj. MAX GAIN adj. AWB & LV standard data input Auto white balance adj. Mechanical shutter adj. Angular velocity sensor sensitivity adj. z VCO adj. z RGB AMP adj. z Color EVF Contrast adj. z Backlight consumption current adj. z White balance adj. z z z VCO adj. z z RGB AMP adj. *1 z Bright adj. *2 z Black limit adj. *2 z LCD Contrast adj. z z V-COM level adj. *1 z Center level adj. *2 z V-COM adj. z z z White balance adj. zz z z z System control Serial No. input CAP FG duty adj. z z Switching position adj. z z Servo, RF AGC center level adj. z z APC & AEQ adj. z z PLL f0 & LPF f0 adj. z z Chroma BPF f0 adj. Video S VIDEO OUT Y level adj. S VIDEO OUT Cr, Cb level adj. IR video carrier frequency adj. IR IR video deviation adj. IR audio deviation adj. Mechanism Tape path adj. z z z z

Table. 5-1-1(1).

5-2

z

z z z z z z

z z z z z z z z

z z

z

z z z z z z z z z zz zz z zz z z z

z z z

Ver 1.1 2000. 06

• Adjusting items when replacing a board or EEPROM (DCR-TRV6/TRV6E/TRV11/TRV11E) When replacing a board or EEPROM, adjust the items indicated by z in the following table. *1: DCR-TRV11/TRV11E model only *2: DCR-TRV6/TRV6E model only

Adjustment

VC-241 board JK-188 board PD-123 board PD-124 board LB-64 board VC-241 board VC-241 board VC-241 board

Adjustment Section

(COMPLETE) (COMPLETE) (COMPLETE) *1 (COMPLETE) *2 (COMPLETE) IC801 (EEPROM) IC502 (EEPROM) IC1407 (Flash memory) *1

Board replacement

Initialization Initialization of C, D, 8 page data of B, C, D, E, Initialization of B page data *1 F, 7, 8 page data Initialization of E, F, 7 page data 36MHz origin oscillation adj. Zoom center adj. Hall adj. Flange back adj. Optical axis adj. Camera Color reproduction adj. MAX GAIN adj. AWB & LV standard data input Auto white balance adj. Mechanical shutter adj. Angular velocity sensor sensitivity adj. VCO adj. RGB AMP adj. Color EVF Contrast adj. Backlight consumption current adj. White balance adj. VCO adj. RGB AMP adj. *1 Bright adj. *2 Black limit adj. *2 LCD Contrast adj. V-COM level adj. *1 Center level adj. *2 V-COM adj. White balance adj. System control Serial No. input CAP FG duty adj. Switching position adj. Servo, RF AGC center level adj. APC & AEQ adj. PLL f0 & LPF f0 adj. Chroma BPF f0 adj. Video S VIDEO OUT Y level adj. S VIDEO OUT Cr, Cb level adj. IR video carrier frequency adj. IR IR video deviation adj. IR audio deviation adj. Mechanism Tape path adj.

z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z

Table. 5-1-1(2).

5-3

z z

z z z z z z z z z z z z z z z z z z z z z z z

• Adjusting items when replacing main parts (DCR-TRV20/TRV20E) When replacing main parts, adjust the items indicated by z in the following table. Note1: When replacing the drum assy., reset the data of page: 2, address: A2 to A4 to “00”. (Refer to “Record of Use check” of “5-4. SERVICE MODE”) Replaced parts

Adjustment Section

Adjustment

Parts replacement

Lens device Mechanism deck Color EVF block LCD902 (LCD panel) LCD block LCD901 (LCD panel) LCD block ND901 (Fluorescent tube) LCD block Inverter unit Control switch block (FK-30150) Mechanism deck M901 (Drum assy) Note1 Mechanism deck M902 (Capstan motor) Mechanism deck LS chassis D3 assy JK-188 board SE3051/3052 (PITCH/YAW sensor) PD-123 board IC2104 (RGB driver (LCD)) *1 PD-123 board IC2105 (Timing generator (LCD)) *1 PD-124 board IC3101 (RGB driver (LCD)) *2 PD-124 board IC3102 (Timing generator (LCD)) *2 LB-64 board ND2201 (Fruorescent tube (EVF)) VC-240 board IC1802 (RGB driver (EVF)) VC-240 board IC1803 (Timing generator (EVF)) CD-252 board IC101 (CCD imager) CD-252 board IC102, X101 (Timing generator) CD-252 board IC104 (CDS, AGC,) VC-240 board IC204 (Lens predriver) VC-240 board IC701 (A/D converter) VC-240 board IC1301 (LINE IN/OUT AMP) VC-240 board IC301 (DV signal process) VC-240 board IC101 (EQ, A/D conv., PLL) VC-240 board IC102 (REC/PB AMP) VC-240 board IC1901 (IR transmitter) VC-240 board IC803 (EVR)

Block replacement

Initialization Initialization of C, D, 8 page data Initialization of B page data of B, C, D, E, F, 7, 8 page data Initialization of E, F, 7 page data 54MHz/66MHz origin oscillation adj. Zoom center adj. z Hall adj. z MR adj. z Flange back adj. z Camera Color reproduction adj. MAX GAIN adj. AWB & LV standard data input Auto white balance adj. Mechanical shutter adj. Angular velocity sensor sensitivity adj. z VCO adj. z RGB AMP adj. z Color EVF Contrast adj. z Backlight consumption current adj. z White balance adj. z z z VCO adj. z z RGB AMP adj. *1 z Bright adj. *2 z Black limit adj. *2 z LCD Contrast adj. z z V-COM level adj. *1 z Center level adj. *2 z V-COM adj. z z z White balance adj. zz z z z System control Serial No. input CAP FG duty adj. z z Switching position adj. z z Servo, RF AGC center level adj. z z APC & AEQ adj. z z PLL f0 & LPF f0 adj. z z Chroma BPF f0 adj. Video S VIDEO OUT Y level adj. S VIDEO OUT Cr, Cb level adj. IR video carrier frequency adj. IR IR video deviation adj. IR audio deviation adj. Mechanism Tape path adj. z zz z

Table. 5-1-2(1).

5-4

z

z z z

z z

z z

z

z

z z

z z

z z

z z

z

z z zz zz zz z zz zz zz z

zz zz zz

• Adjusting items when replacing a board or EEPROM (DCR-TRV20/TRV20E) When replacing a board or EEPROM, adjust the items indicated by z in the following table. *1: DCR-TRV20 model only *2: DCR-TRV20E model only *3: Perform this adjustment when replace the CCD imager (IC101) and this board at the same time.

Adjustment

CD-252 board VC-240 board JK-188 board PD-123 board PD-124 board LB-64 board VC-240 board VC-240 board VC-240 board

Adjustment Section

(COMPLETE) (COMPLETE) (COMPLETE) (COMPLETE) *1 (COMPLETE) *2 (COMPLETE) IC801 (EEPROM) IC502 (EEPROM) IC1406 (EEPROM)

Board replacement

Initialization Initialization of C, D, 8 page data of B, C, D, E, Initialization of B page data F, 7, 8 page data Initialization of E, F, 7 page data 54MHz/66MHz origin oscillation adj. Zoom center adj. Hall adj. MR adj. Flange back adj. Camera Color reproduction adj. MAX GAIN adj. AWB & LV standard data input Auto white balance adj. Mechanical shutter adj. Angular velocity sensor sensitivity adj. VCO adj. RGB AMP adj. Color EVF Contrast adj. Backlight consumption current adj. White balance adj. VCO adj. RGB AMP adj. *1 Bright adj. *2 Black limit adj. *2 LCD Contrast adj. V-COM level adj. *1 Center level adj. *2 V-COM adj. White balance adj. System control Serial No. input CAP FG duty adj. Switching position adj. Servo, RF AGC center level adj. APC & AEQ adj. PLL f0 & LPF f0 adj. Chroma BPF f0 adj. Video S VIDEO OUT Y level adj. S VIDEO OUT Cr, Cb level adj. IR video carrier frequency adj. IR IR video deviation adj. IR audio deviation adj. Mechanism Tape path adj.

z z z z zz z z z z z z z zz z *3 z z z z *3 z z *3 z z z z z z z z z z z z z z z zz z z z z z z z zz z z z z z zz z zz z z z z z z z z z z z z z z z

Table. 5-1-2(2).

5-5

z z

z z z z z z z

z z z z z z z z z z z z z

5-1. CAMERA SECTION ADJUSTMENT 1-1.

PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)

1-1-1. List of Service Tools • Oscilloscope • Regulated power supply Ref. No.

• Color monitor • Digital voltmeter

Name

• Vectorscope Parts Code

Usage

ND filter 1.0

Auto white balance adjustment/check White balance adjustment/check J-6080-808-A White balance check

J-2

ND filter 0.4 ND filter 0.1

J-6080-806-A White balance check J-6080-807-A White balance check

J-3 J-4

Pattern box PTB-450 Color chart for pattern box

J-6082-200-A J-6020-250-A

J-1

Filter for color temperature correction (C14)

J-6080-058-A

J-6

Adjustment remote commander (RM-95 upgraded). J-6082-053-B (Note 1) Siemens star chart J-6080-875-A For checking the flange back

J-7

Clear chart for pattern box

J-6080-621-A

J-8

CPC-8 jig

For adjusting the video section J-6082-388-A For adjusting the color viewfinder For adjusting the LCD block

J-9

Extension cable (80P, 0.4mm)

J-6082-395-A

J-10

IR receiver jig

For extension between the DD-137 board (CN1603) and the VC-240/241 board (CN002) J-6082-383-A For adjusting the IR transmitter

J-11 J-12

Mini pattern box Camera table

J-6082-353-B For adjusting the flange back J-6082-384-A For adjusting the flange back

J-5

Note 1: If the micro processor IC in the adjustment remote commander is not the new micro processor (UPD7503G-C56-12), the pages cannot be switched. In this case, replace with the new micro processor (8-759-148-35).

J-1

J-2

J-3

J-4

J-5

J-6

J-7

J-8

J-9

J-10

J-11

J-12

Fig. 5-1-1.

5-6

1-1-2.

Preparations

Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled.

1)

Pattern Box

Connect the equipment for adjustments according to Fig. 5-1-2.

Note 3: As removing the cabinet (R) (removing the VC-240/241 board CN003) means removing the lithium 3V power supply (BT3201), data such as date, time, user-set menus will be lost. After completing adjustments, reset these data. If the cabinet (R) has been removed, the self-diagnosis data, data on history of use (total drum rotation time etc. ) will be lost. Before removing, note down the self-diagnosis data and the data on history use (data of page: 2, address: A2 to AA). (Refer to “SELF-DIAGNOSIS FUNCTION” for the self-diagnosis data, and to “5-4.Service Mode” for the data on the history use.)

1.5m

Note 4: Setting the “Forced Camera Power ON” Mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the camera power to be turned on with the control switch block (FK-30150) removed. After completing adjustments, be sure to exit the “Forced Camera Power ON Mode”.

Front of the lens

Fig. 5-1-2.

Note 5: Exiting the “Forced Camera Power ON” Mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00.

5-7

Extension cable J-6082-395-A (80P 0.4mm)

Must be connected when performing the color EVF system adjustments. AC power adaptor (8.4Vdc) CN1604

Adjustment remote commander

AC - L10 or AC - VQ800

Battery terminal

CN1603

DD-137 board CN1601 CN1602

Front panel block FP-180

LANC/ DIGITAL I/O jack

CN008 CN007 CN006

CN005

CN101 CN002

DC IN jack AUDIO/VIDEO jack JK-188 board

VC-240/241 board CN701 CN009 CN001

MA-385 board CN2071

CN003

Must be connected when performing the video system, color EVF system or LCD system adjustments.

AUDIO L (White) AUDIO R (Red)

FP-179

VIDEO (Yellow)

CK-92/94 board

Color monitor

CN3205 CN3203

CN3201 CN3206

CPC-8 jig (J-6082-388-A) Vector scope CN3204

Cabinet (R)

Terminated at 75 Ω

Note : VC-240 board : DCR-TRV20/TRV20E VC-241 board : DCR-TRV6/TRV6E/TRV11/TRV11E CK-92 board : DCR-TRV11/TRV11E/TRV20 CK-94 board : DCR-TRV6/TRV6E/TRV20E

Fig. 5-1-3.

5-8

1-1-3. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. 1. 2. 3. 4. 5. 6. 7.

POWER switch (PS-30150 block) ......................... CAMERA NIGHT SHOT switch (Lens block) ................................. OFF DEMO MODE (Menu setting) ........................................ OFF DIGITAL ZOOM (Menu setting) .................................... OFF STEADY SHOT (Menu setting) ...................................... OFF PROGRAM AE (CF-30150) ........................................ AUTO WHITE BALANCE (Menu setting) ............................ AUTO

8. 9. 10. 11. 12. 13.

16 : 9 WIDE (Menu setting) ............................................ OFF PICTURE EFFECT (Menu setting) ................................. OFF DISPLAY (Menu setting) .................................. V-OUT/LCD DISPLAY (CK-92/94 board) ............................................ ON FOCUS switch (MA-385 board) ........................... MANUAL DIGITAL EFFECT (CK-92/94 board) ............................ OFF

2. Order of Adjustments Basically carry out adjustments in the order given.

Color bar chart (Color reproduction adjustment frame )

Electronic beam scanning frame

A B

A=B

C

C=D

D Yellow Cyan Green White Magenta Red Blue

Blue

Yellow Cyan Green White Magenta Red

H

CRT picture frame

V

B A

Fig. b (TV monitor picture)

Enlargement

Fig. a (Video output terminal output waveform)

Difference in level

B

Adjust the camera zoom and direction to obtain the output waveform shown in Fig. a and the TV monitor display shown in Fig. b.

A

Fig.5-1-4. 3. Subjects 1) Color bar chart (Color reproduction adjustment frame) When performing adjustments using the color bar chart, adjust the picture frame as shown in Fig. 5-1-4. (Color reproduction adjustment frame) 2) Clear chart (Color reproduction adjustment frame) Remove the color bar chart from the pattern box and insert a clear chart in its place. (Do not perform zoom operations during this time.) 3) Flange back adjustment chart Make the chart shown in Fig. 5-1-5 using A0 size (1189mm × 841mm) black and white vellum paper.

White 841mm Black

1189mm

Fig. 5-1-5. Note: Use matte vellum paper bigger than A0, and make sure the edges of the black and white paper joined together are not rough.

5-9

1-2.

3. C Page Table

INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE DATA

1-2-1.

Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the C, D, 8 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8 Page Data”.)

INITIALIZATION OF C, D, 8 PAGE DATA

1. Initializing the C, D, 8 Page Data

Address Note1: If “Initializing the C, D, 8 Page Data” is performed, all data of the C page, D page and 8 page will be initialized. (It is impossible to initialize a single page.) Note2: If the C, D, 8 page data has been initialized, the following adjustments need to be performed again. 1) Modification of C, D, 8 page data 2) Serial No. input 3) Servo and RF system adjustments 4) Video system adjustments 5) Color viewfinder system adjustments 6) LCD system Adjustments

Adjusting page

C

Adjusting Address Adjusting page

10 to FF D

Adjusting Address Adjusting page

10 to FF 8

Adjusting Address

00 to FF

00 to 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D to 3F

Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 81, and check that the data is “00”. 3) Select page: 3, address: 80, set data: 0A, and press the PAUSE button of the adjustment remote commander. 4) Select page: 3, address: 80, and check that the data changes to “1A”. 5) Perform “Modification of C, D, 8 Page Data”. 2. Modification of C, D, 8 Page Data If the C, D, 8 page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model.

40 41 42 43 to 4B

Note: If copy the data built in the different model, the camcorder may not operate.

3)

4)

When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data to write the data in the non-volatile memory. Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value.

4C 4D

Processing after Completing Modification of C, D, 8 Page data 1) Select page: 2, address: 00, and set data: 29. 2) Select page: 2, address: 01, and set data: 29, and press the PAUSE button of the adjustment remote commander.

4E 4F 50 51

Note: If the following symptoms occur after completing of the “Modification of C, D, 8 page data”, check that the data of the “Fixed data-2” addresses of D page are same as those of the same model of the same destination. 1) The battery end mark on the LCD or viewfinder screen is flashing. 2) The power is shut off so that unit cannot operate.

52 to 63 64 65 to 83 84 85

5-10

Initial value EE 00 00 00

E0 2A 2A 32 32 25 3E 3E DC 99

88 E3 A1 04 20

03

Remark Switching position adj.

Fixed data-1 (Initialized data) Cap FG duty adj. Fixed data-2 AEQ adj. Fixed data-1 AEQ adj. Fixed data-1 AGC center level adj. PLL f0 adj. APC adj. LPF f0 adj. Fixed data-1 (Initialized data) S VIDEO out Y level adj. S VIDEO out Cr level adj. S VIDEO out Cb level adj. Chroma BPF f0 adj. PLL f0 fine adj. Fixed data-1 (Initialized data) APC adj. Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1

Address 86 87 88 89 8A to 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 to BF C0 C1 to D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 to E3 E4 E5

Initial value

Remark

Address

Initial value

E6

Fixed data-2 (Modified data. Copy the data built in the same model.)

E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF

Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)

Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)

Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.)

08 00 46 01 02 00 00 00

Remark Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Serial No. input

Fixed data-1 (Initialized data)

00 00 00 00 00 00 00 00 00 00 00 00

Emergency memory address

Table. 5-1-3.

Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)

Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)

5-11

Ver 1.1 2000. 06

4. D Page Table Address Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the C, D, 8 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8 Page Data”.)

64 65

*1: TRV11/TRV11E/TRV20 model only *2: TRV6/TRV6E/TRV20E model only *3: TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E Address 00 to 0F 10 11 12 13 14 15 to 1C 1D 1E to 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 to 41 42 43 44 45 46 to 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D to 63

Initial value 00

Initial value

66 67 68

Remark 69 to 8D 8E 8F 90 to 91 92 5D/7D *4 93 5D/7D *4 94 95 AC 96 97 80 98 80 99 1D 9A 9B 9C E0 9D E0 9E 11 9F A0 A1 A2 45/6F/A5/A5/ 98/6C *3 A3 6B/4A/A5/A5/ 98/61 *3 A4 27/27/88/88/ 91/27 *3 A5 B5/B5/2B/2B/ 2C/B5 *3 A6 05/05/00/00/ 00/05 *3 A7 B9/B9/CE/CE/ A1/B9 *3 A8 8A/8A/7F/7F/ 7F/8A *3 A9 72/72/87/87/ 87/72 *3 AA 25/25/37/37/ 3F/25 *3 AB 27/27/80/80/ 80/64 *3 AC AD AE AF B0 B1 B2 B3 B4

Test mode Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)

Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)

Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)

5-12

Remark Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 Fixed data-1 VCO adj. (EVF) *4: NTSC/PAL Fixed data-2 RGB AMP adj.(EVF) Fixed data-1 White balance adj. (EVF) Contrast adj. (EVF) Fixed data-1 Fixed data-2 Backlight consumption current adj. (EVF) Fixed data-1 (Initialized data) VCO adj. (LCD)

V-COM adj. (LCD) RGB AMP adj. (LCD) *1 Bright adj.(LCD) *2 Black limit adj.(LCD) *2 Fixed data *1 V-COM level adj. (LCD) *1 Fixed data *2 White balance adj. (LCD)

Contrast adj. (LCD) Center level adj.(LCD) *2 Fixed data *1 Fixed data-2 (Modified data. Copy the data built in the same model.)

Fixed data-1 (Initialized data) Fixed data-2

5. 8 Page Table Address B5

B6 B7 B8 B9 BA BB to C3 C4 C5 C6 C7 to D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC to FF

Initial value

Remark Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the C, D, 8 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8 Page Data”.)

Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data)

Address

Remark

00 to 52 Fixed data-1 (Initialized data) 53 Fixed data-2 (Modified data. Copy the data built in the same model.) 54 to 98 Fixed data-1 (Initialized data) 99 Fixed data-2 (Modified data. Copy the data built in the same model.) 9A to A4 Fixed data-1 (Initialized data) A5 Fixed data-2 A6 Fixed data-1 A7 Fixed data-2 A8 (Modified data. Copy the data built in the same model.) A9 to FF Fixed data-1 (Initialized data)

Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data)

Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data)

Table. 5-1-5.

Table. 5-1-4.

5-13

Ver 1.1 2000. 06

1-2-2.

INITIALIZATION OF B PAGE DATA (DCR-TRV11/TRV11E/TRV20/TRV20E)

3. Initializing the B Page Data (DCR-TRV11/TRV11E) Note: If the B page data has been initialized, the following adjustments need to be performed again. 1) Modification of B page data

Note: When reading the B page data, insert a “Memory Stick” into the “Memory Stick” slot.

Switch setting: POWER ................................................................. MEMORY 1. Initializing the B Page Data (DCR-TRV20/TRV20E) Note: If the B page data has been initialized, the following adjustments need to be performed again. 1) Modification of B page data

Adjusting page

B

Adjusting Address

00 to FF

B

Adjusting Address

00 to FF

Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 3) Select page: 2, address: 8F, set data: 03, and press the PAUSE button. 4) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 5) Select page: 2, address: 8F, set data: 00, and press the PAUSE button. 6) Select page: 5, address: 0E, set data: 00, and press the PAUSE button. 7) Select page: 5, address: 01, set data: F3, and press the PAUSE button. 8) Select page: 5, address: 00, set data: 01, and press the PAUSE button. 9) Select page: 5, address: 0E, and check that the data is “01”. 10) Perform “Modification of B Page Data”.

Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 3) Select page: 2, address: 8F, set data: 03, and press the PAUSE button. 4) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 5) Select page: 2, address: 8F, set data: 00, and press the PAUSE button. 6) Select page: 5, address: 01, set data: F3, and press the PAUSE button. 7) Select page: 5, address: 00, set data: 01, and press the PAUSE button. 8) Select page: 5, address: 01, and wait for three seconds. 9) Select page: 5, address: 00, and check that the data is “00”. 10) Select page: 5, address: 02, and check that the data is “00”. 11) Perform “Modification of B Page Data”.

4. Modification of B Page Data (DCR-TRV11/TRV11E) If the B page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Preparations: 1) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 2) Select page: 2, address: 8F, set data: 03, and press the PAUSE button. 3) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 4) Select page: 2, address: 8F, set data: 00, and press the PAUSE button.

2. Modification of B Page Data (DCR-TRV20/TRV20E) If the B page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Preparations: 1) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 2) Select page: 2, address: 8F, set data: 03, and press the PAUSE button. 3) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 4) Select page: 2, address: 8F, set data: 00, and press the PAUSE button.

Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the camcorder may not operate.

Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model.

3)

When changing the data, don’t press the PAUSE button.

Processing after Completing Modification of B Page data: 1) Select page: 5, address: 0E, set data: 00, and press the PAUSE button. 2) Select page: 5, address: 01, set data: FB, and press the PAUSE button. 3) Select page: 5, address: 00, set data: 01, and press the PAUSE button. (The changed data are written in the flash memory.) 4) Select page: 5, address: 0E, and check that the data is “01”. 5) Select page: 2, address: 00, and set data: 29. 6) Select page: 2, address: 01, set data: 29, and press the PAUSE button.

Note: If copy the data built in the different model, the camcorder may not operate.

3)

Adjusting page

When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data to write the data in the non-volatile memory.

Processing after Completing Modification of B Page data: 1) Select page: 2, address: 00, and set data: 29. 2) Select page: 2, address: 01, set data: 29, and press the PAUSE button.

5-14

Ver 1.1 2000. 06

5. B Page Table

1-2-3.

Note: Fixed data-1: Initialized data. (Refer to “1. or 3. Initializing the B Page Data”.) Fixed data-2: Modified data. (Refer to “2. or 4. Modification of B Page Data”.)

1. Initializing the E, F, 7 Page Data

Address

INITIALIZATION OF E, F, 7 PAGE DATA

Note1: If “Initializing the E, F, 7 Page Data” is performed, all data of the E page, F page and 7 page will be initialized. (It is impossible to initialize a single page.) Note2: If the E, F, 7 page data has been initialized, following adjustments need to be performed again. 1) Modification of E, F, 7 page data 2) Camera system adjustments 3) IR transmitter adjustments

Remark

00 Fixed data-2 01 to 16 Fixed data-1 (Initialized data) 17 Fixed data-2 (Modified data. Copy the data built in the same 18 model.) 19 1A to 20 Fixed data-1 (Initialized data) 21 Fixed data-2 22 to 4F Fixed data-1 (Initialized data) 50 Fixed data-2 51 to 53 Fixed data-1 (Initialized data) 54 Fixed data-2 55 to 5D Fixed data-1 (Initialized data) 5E Fixed data-2 5F 60 to 6F Fixed data-1 (Initialized data) 70 Fixed data-2 71 to FF Fixed data-1 (Initialized data)

Adjusting page

F

Adjusting Address Adjusting page

10 to FF E

Adjusting Address Adjusting page

00 to FF 7

Adjusting Address

DCR-TRV6/TRV6E/TRV11/TRV11E: 00 to 59 DCR-TRV20/TRV20E: 00 to A3 (Note3) 00 to B5 (Note4)

Note3: Camera microprocessor ver. 1.0 Note4: Camera microprocessor ver. 2.0 or later

Switch setting: POWER .................................................................. CAMERA Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 01, and set the following data and press the PAUSE button. 2D: DCR-TRV6/TRV11/TRV20 (NTSC) 2F: DCR-TRV6E/TRV11E/TRV20E (PAL) 3) Select page: 6, address: 03, set data: 01, and press the PAUSE button. 4) Select page: 6, address: 02, and check that the data changes to “01”. 5) Perform “Modification of E, F, 7 Page Data”.

Table. 5-1-6.

2. Modification of E, F, 7 Page Data If the E, F, 7 page data has been initialized, change the data of the “Fixed data-2” address shown in the following table by manual input. Version check of the camera microprocessor: 1) The data of page: 6, address: FF shows the version of the camera microprocessor (VC-240/241 board IC802). Data 01 02

Version 1.0 2.0

Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the camcorder may not operate.

3)

4)

When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data to write the data in the non-volatile memory. Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value.

Processing after Completing Modification of E, F, 7 Page data 1) Turn off the power and turn on again.

5-15

3. F Page Table Address Initial value *5 VC-240 VC-241 38 39 3A 3B 3C 00 00 3D F1/EF F1/EF *4 *4 3E 3F 40 80 80 41 40 40 42 43 44 45 46 47 48 49 4A 84 51 4B 4A 19 4C AD 22 4D 47 20 4E F0 93 4F 21 13 50 80 00 51 80 00 52 40 *3 53 C0 *3 54 40 *3 55 C0 *3 56 40 *3 57 C0 *3 58 40 *3 59 C0 *3 5A 8F 46 5B EF 00 5C 19 19 5D 00 00 5E 1B 2A 5F 86 00 60 00 00 61 00 00 62 00 00 63 00 *3 64 65 66 47/5E 56/7C *4 *4 67 51/60 68/6F *4 *4 68 69 *3 00 6A 6B

Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 7 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 7 Page Data”.)

*1: *2: *3: *4:

DCR-TRV6/TRV6E/TRV11/TRV11E model only DCR-TRV20/TRV20E model only Fixed data-1 NTSC/PAL NTSC: DCR-TRV6/TRV11/TRV20 PAL: DCR-TRV6E/TRV11E/TRV20E *5: VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E Address Initial value *5 Remark VC-240 VC-241 00 to 0F 10 Fixed data-1 11 (Initialized data) 12 80 80 36MHz origin osc adj. *1 54/66MHz origin osc adj. *2 13 80 80 Zoom center adj. 14 Fixed data-1 (Initialized data) 15 16 17 81 81 HALL adj. 18 5D A0 19 17 17 1A 70 *3 HALL adj. *2 1B 62 *3 1C 8D *3 1D 80 9A Max gain adj. 1E 80 80 AWB & LV standard data input 1F 7A 7A 20 Fixed data-1 21 (Initialized data) 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 90 90 AWB & LV standard data input 31 3E 3E 32 43 43 33 59 59 34 Fixed data-1 35 22 22 Color reproduction adj. 36 Fixed data-1 37 27/24 27/24 Color reproduction adj. *4 *4

5-16

Remark Fixed data-1 (Initialized data)

Color reproduction adj.

Fixed data-1 Auto white balance adj. Fixed data-1 (Initialized data)

Flange back adj.

Flange back adj. *1 MR adj. *2 MR adj. *2

Flange back adj.

Flange back adj. *2 Fixed data-1 (Initialized data) Angular velocity sensor sensitivity adj.

Fixed data-1 Optical axis adj. *1 Fixed data-1 (Initialized data)

Address Initial value *5 VC-240 VC-241 6C 00 00 6D 00 00 6E 00 00 6F 70 81 C4 71 0B 0E 72 94 75 73 09 0C 74 66 26 75 08 0B 76 84 35 77 07 0A 78 9B 6E 79 05 09 7A 25 A5 7B 43 61 7C 44 A1 7D 4A 79 7E 44 64 7F 47 81 80 52 82 81 3F 84 82 44 B5 83 30 7B 84 21 20 85 86 87 88 89 8A 8B 8C 02 *3 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 to AF B0

00 00

*3 *6

Address Initial value *5 VC-240 VC-241 B1 B2 to B3 B4 B5 to BB BC BD to D0 D1 D2 to D4 D5 D6 to DC DD DE to FF

Remark IR video carrier freq. Adj. IR video deviation Adj. IR audio deviation Adj. Fixed data-1 Mechanical shutter adj.

Remark Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)

Table. 5-1-7.

Fixed data-1 (Initialized data)

Max gain adj. *2 Fixed data-1 Fixed data-2 (Copy the data built in the same model.) Fixed data-1 (Initialized data)

Max gain adj. *2 *6: Fixed data-2 Fixed data-1 Fixed data-2

5-17

4. E Page Table Address Initial value *5 VC-240 VC-241 78 79 to 7E 7F 80 to 83 84 85 86 87 88 to 8B 8C 8D to 8E 8F 90 91 92 93 to 94

Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 7 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 7 Page Data”.) Note2: Refer to “2. Modification of E, F, 7 Page Data” for the camera microprocessor version.

*1: *2: *3: *4: *5:

Camera microprocessor ver. 1.0 Camera microprocessor ver. 2.0 or later Fixed data-1 DCR-TRV6/TRV6E/TRV11/TRV11E model only VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E

Address Initial value *5 Remark VC-240 VC-241 00 to 02 Fixed data-1 (Initialized data) 03 Fixed data-2 04 to 11 Fixed data-1 (Initialized data) 12 Fixed data-2 13 Fixed data-1 (Initialized data) 14 15 Fixed data-2 16 to 1A Fixed data-1 (Initialized data) 1B Fixed data-2 1C Fixed data-1 1D Fixed data-2 1E to 38 Fixed data-1 39 Fixed data-2 3A 3B to 3C Fixed data-1 3D Fixed data-2 3E to 49 Fixed data-1 (Initialized data) 4A 63 *1 *3 *1: Camera microprocessor ver. 1.0 83 *2 *2: Camera microprocessor ver. 2.0 or later *3: Fixed data-1 4B to 4F Fixed data-1 (Initialized data) 50 Fixed data-2 51 to 63 Fixed data-1 (Initialized data) 64 Fixed data-2 65 66 to 69 Fixed data-1 6A Fixed data-2 6B to 6D Fixed data-1 6E Fixed data-2 6F to 70 Fixed data-1 71 Fixed data-2 72 (Modified data. Copy the data built in the same model.) 73 74 75 to 77 Fixed data-1 (Initialized data)

95 96 97 98 99 to A1 A2 A3 to AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB to CE CF D0

*3

D1 to DD DE DF to FF

*3

Remark Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2

Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2

Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)

Fixed data-1 Fixed data-2 26/24 Optical axis adj. *4 *6 *6: NTSC/PAL Fixed data-1 (Initialized data) 5F/71 Optical axis adj.*4 *6 *6: NTSC/PAL Fixed data-1 (Initialized data)

Table. 5-1-8.

5-18

5. 7 Page Table Address Initial value *1 Remark VC-240 VC-241 AA Fixed data-2 (Note2) (Note3) AB (Modified data. Copy the data built in the same model.) AC AD AE AF B0 B1 B2 B3 B4 B5

Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 7 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 7 Page Data”). Note2: Addresses: 5A to B5 are only for DCR-TRV20/TRV20E model. Note3: Addresses: A4 to B5 are only for the camera microprocessor version 2.0 or later.

*1: VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E Address Initial value *1 Remark VC-240 VC-241 00 Fixed data-2 01 to 03 Fixed data-1 (Initialized data) 04 Fixed data-2 05 (Modified data. Copy the data built in the same model.) 06 07 08 09 to 15 Fixed data-1 (Initialized data) 16 Fixed data-2 17 (Modified data. Copy the data built in the same model.) 18 19 1A 1B Fixed data-1 1C Fixed data-2 (Modified data. Copy the data built in 1D the same model.) 1E 1F 20 21 to 22 Fixed data-1 23 7A 7C Mechanical shutter adj. 24 80 7F 25 80 7C 26 82 7B 27 to 3C Fixed data-1 (Initialized data) 3D Fixed data-2 3E to 44 Fixed data-1 (Initialized data) 45 Fixed data-2 46 to 51 Fixed data-1 52 Fixed data-2 53 54 to 59 Fixed data-1 5A to 84 Fixed data-1 (Note2) 85 Fixed data-2 (Note2) 86 to A3 Fixed data-1 (Note2) (Initialized data) A4 Fixed data-2 (Note2) (Note3) (Modified data. Copy the data built in A5 the same model.) A6 A7 A8 A9

Table. 5-1-9.

5-19

1-3.

CAMERA SYSTEM ADJUSTMENTS

Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. Note: NTSC model: DCR-TRV6/TRV11/TRV20 PAL model: DCR-TRV6E/TRV11E/TRV20E

2. 54MHz/66MHz Origin Oscillation Adjustment (DCR-TRV20/TRV20E) (CD-252 board) Set the frequency of the clock for synchronization. If deviated, the synchronization will be disrupted and the color will become inconsistent.

1. 36MHz Origin Oscillation Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) (VC-241 board) Set the frequency of the clock for synchronization. If deviated, the synchronization will be disrupted and the color will become inconsistent. Subject Not required

Subject Measurement Point

Not required Pin qh of IC701 of VC-240 board or pin 7 of IC1901 of VC-240 board

Measurement Point Measuring Instrument

Pin qh of IC701 or pin 7 of IC1901 Frequency counter

Adjustment Page Adjustment Address

F 12

Measuring Instrument Adjustment Page

Frequency counter F

Specified Value

Pin qh of IC701: f=18000000 ± 90Hz Pin 7 of IC1901: f=3579545 ± 18Hz (Note)

Adjustment Address Specified Value

12 Pin qh of IC701 of VC-240 board : f=33000000 ± 165Hz (NTSC) f=27000000 ± 134Hz (PAL) Pin 7 of IC1901 of VC-240 board: f=3579545 ± 18Hz (Note)

Note: SUPER LASER LINK ................................... ON (Red LED is lit)

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: F, address: 12, change the data and set the clock frequency (f) to the specified value. 3) Press the PAUSE button of the adjustment remote commander. 4) Select page: 0, address: 01, and set data: 00.

25 12

1 36

13

Note: SUPER LASER LINK ................................... ON (Red LED is lit)

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: F, address: 12, change the data and set the clock frequency (f) to the specified value. 3) Press the PAUSE button of the adjustment remote commander. 4) Select page: 0, address: 01, and set data: 00.

VC-240/241 board

24 13 12

IC701 1

48 37 48

24

37 25

36

IC1901

Fig. 5-1-6.

5-20

4. HALL Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) For detecting the position of the lens iris, adjust AMP gain and offset. Subject Not required

3. Zoom Key Center Adjustment Set the A/D value center of the microprocessor to the center voltage of the zoom key. If deviated, the zoom lens operates of itself, even if the zoom key is the center position. Subject Not required Measurement Point Measuring Instrument

Display data of page: 6, address: 50 Adjustment remote commander

Adjustment Page Adjustment Address

F 13

Note: Don’t touch the zoom lever during adjustment.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 50, read the data, and this data is named D50. 3) Select page: F, address: 13, set data: D50. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: 0, address: 01, and set data: 00.

Measurement Point Measuring Instrument

Display data of page 1 (Note1) Adjustment remote commander

Adjustment Page Adjustment Address

F 17, 18, 19

Specified Value

When the data of page: 6, address: 01 is “01”: 15 to 19 (Note2) When the data of page: 6, address: 01 is “03”: 87 to 8B (Note2)

Note1: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX IRIS display data Note2: The PAUSE button of the Adjustment remote commander must be pressed.

Switch setting: POWER .................................................................. CAMERA Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 94, and set data: 17. 3) Select page: 6, address: 95, and set data: 89. 4) Select page: 6, address: 01, set data: 6D, and press the PAUSE button of the adjustment remote commander. (The HALL adjustment is performed and the adjustment data is stored in page: F, address: 17 to 19.) 5) Select page: 6, address: 02, and check that the data is “01”. 6) Select page: 6, address: 01, set data: 00, and press the PAUSE button. Checking method: 1) Select page: 6, address: 04, and set data: 03. 2) Select page: 6, address: 01, set data: 01, and press the PAUSE button. 3) Select page: 1, and check that the IRIS display data (Note1) satisfies the specified value. 4) Select page: 6, address: 01, set data: 03, and press the PAUSE button. 5) Select page: 1, and check that the IRIS display data (Note1) satisfies the specified value. Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 04, and set data: 00. 3) Select page: 6, address: 94, and set data: 00. 4) Select page: 6, address: 95, and set data: 00. 5) Select page: 0, address: 01, and set data: 00.

5-21

5. HALL Adjustment (DCR-TRV20/TRV20E) For detecting the position of the lens iris and ND filter, adjust each AMP gain and offset. Subject Not required Measurement Point Measuring Instrument

Display data of page 1 (Note1) Adjustment remote commander

Adjustment Page Adjustment Address

F 17, 18, 19, 1A, 1B, 1C

Specified Value

When the data of page: 6, address: 01 is “01”: 15 to 19 (Note2) When the data of page: 6, address: 01 is “03”: 87 to 8B (Note2) When the data of page: 6, address: 01 is “69”: 87 to 8B (Note2) When the data of page: 6, address: 01 is “6B”: 15 to 19 (Note2)

6. MR Adjustment (DCR-TRV20/TRV20E) The MR (Magnet resistor) adjustment of the inner focus lens is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. Subject Not required Measurement Point Measuring Instrument

Adjustment remote commander

Adjustment Page Adjustment Address

F 50 to 59, 62

Specified Value

40 to C0 (Address: 50) 40 to C0 (Address: 51) 03 to 78 (Address: 52, 54, 56, 58) 88 to F8 (Address: 53, 55, 57, 59)

Note: Make the lens horizontal and perform this adjustment.

Switch setting: POWER .................................................................. CAMERA

Note1: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX IRIS display data ND display data Note2: The PAUSE button of the Adjustment remote commander must be pressed.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 01, set data: BD, and press the PAUSE button of the adjustment remote commander. (The MR adjustment is performed and the adjustment data is stored in page: F, address: 50 to 59, 62.) 3) Select page: 6, address: 02, and check that the data is “01”. 4) Select page: F, address: 50, and check that the data satisfies the specified value. 5) Select page: F, address: 51, and check that the data satisfies the specified value. 6) Select page: F, address: 52, 54, 56 and 58, and check that the data satisfies the specified value. 7) Select page: F, address: 53, 55, 57 and 59, and check that the data satisfies the specified value.

Switch setting: POWER .................................................................. CAMERA Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 94, and set data: 17. 3) Select page: 6, address: 95, and set data: 89. 4) Select page: 6, address: 01, set data: 6D, and press the PAUSE button of the adjustment remote commander. (The HALL adjustment is performed and the adjustment data is stored in page: F, address: 17 to 1C.) 5) Select page: 6, address: 02, and check that the data is “01”. 6) Select page: 6, address: 01, set data: 00, and press the PAUSE button.

Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 0, address: 01, set data: 00. 3) Turn off the power and turn on again. 4) Perform “Flange Back Adjustment”.

Checking method: 1) Select page: 6, address: 04, and set data: 03. 2) Select page: 6, address: 01, set data: 01, and press the PAUSE button. 3) Select page: 1, and check that the IRIS display data (Note1) satisfies the specified value. 4) Select page: 6, address: 01, set data: 03, and press the PAUSE button. 5) Select page: 1, and check that the IRIS display data (Note1) satisfies the specified value. 6) Select page: 6, address: 01, set data: 69, and press the PAUSE button. 7) Select page: 1, and check that the ND display data (Note1) satisfies the specified value. 8) Select page: 6, address: 01, set data: 6B, and press the PAUSE button. 9) Select page: 1, and check that the ND display data (Note1) satisfies the specified value. Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 04, and set data: 00. 3) Select page: 6, address: 94, and set data: 00. 4) Select page: 6, address: 95, and set data: 00. 5) Select page: 0, address: 01, and set data: 00.

5-22

7. Flange Back Adjustment (Using Minipattern Box) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. Subject Siemens star chart with ND filter for the minipattern box (Note2) Measurement Point Measuring Instrument

Check operation on TV monitor

Adjustment Page Adjustment Address

F DCR-TRV6/TRV6E/TRV11/TRV11E: 13, 4A to 51, 5A to 62 DCR-TRV20/TRV20E: 13, 4A to 4F, 5A to 63

Adjusting method: 1) Install the minipattern box so that the distance between it and the front of the lens of the camcorder is less than 3cm. 2) Make the height of the minipattern box and the camcorder equal. 3) Check that the output voltage of the regulated power supply is the specified voltage. 4) Check that at both the zoom lens TELE end and WIDE end, the center of the Siemens star chart and center of the exposure screen coincide. 5) Select page: 0, address: 01, and set data: 01. 6) Select page: 6, address: 02, and check that the data is “00”. 7) Select page: 6, address: 01, set data: 13, and press the PAUSE button of the adjustment remote commander. Note: Don’t touch the zoom lever. If you touch the zoom lever, the zoom center adjustment data will be rewritten in the value which isn’t correct.

Note1: Perform this adjustment after performing “HALL Adjustment” and “MR Adjustment (DCR-TRV20/TRV20E)”. Note2: Dark Siemens star chart.

8)

Select page: 6, address: 01, set data: 27, and press the PAUSE button. (The adjustment data will be automatically input to the adjustment addresses.) 9) Select page: 6, address: 02, and check that the data is “01”. 10) Only for DCR-TRV20/TRV20E model, select page: F, address: 63, and check that the data is “00” to “0E”.

Switch setting: POWER .................................................................. CAMERA NIGHT SHOT .................................................................. OFF Preparations before adjustments: The minipattern box is installed as shown in the following figure.

Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 0, address: 01, and set data: 00. 3) Turn off the power and turn on again. 4) Perform “Flange Back Check”.

Note: The attachment lenses are not used.

Specified voltage: The specified voltage varies according to the minipattern box, so adjust the power supply output voltage to the specified voltage written on the sheet which is supplied with the minipattern box. Below 3 cm Minipattern box Camcorder Camera table Regulated power supply Output voltage : Specified voltage ±0.01Vdc Output current : more than 3.5A

Red (+) Black (–) Yellow (SENS +) White (SENS –)

Need not connected

Black (GND)

Fig. 5-1-7.

5-23

8. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. 8-1. Flange Back Adjustment (1) Perform this adjustment after performing “HALL Adjustment” and “MR Adjustment (DCR-TRV20/TRV20E)”. Subject Flange back adjustment chart (2.0 m from the front of the lens) (Luminance: 350 ± 50 lux)

8-2. Flange Back Adjustment (2) Perform this adjustment after performing “Flange Back Adjustment (1)”. Subject Subject more than 500m away (Subjects with clear contrast such as buildings, etc.)

Measurement Point Measuring Instrument

Check operation on TV monitor

Measurement Point Measuring Instrument

Check operation on TV monitor

Adjustment Page Adjustment Address

F DCR-TRV6/TRV6E/TRV11/TRV11E: 13, 4A to 51, 5A to 62 DCR-TRV20/TRV20E: 13, 4A to 4F, 5A to 63

Adjustment Page Adjustment Address

F DCR-TRV6/TRV6E/TRV11/TRV11E: 13, 4A to 51, 5A to 62 DCR-TRV20/TRV20E: 13, 4A to 4F, 5A to 63

Switch setting: POWER .................................................................. CAMERA NIGHT SHOT .................................................................. OFF

Switch setting: POWER .................................................................. CAMERA NIGHT SHOT .................................................................. OFF

Adjusting method: 1) Check that at both the zoom lens TELE end and WIDE end, the center of the chart for the flange back adjustment and center of the exposure screen coincide. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: 6, address: 02, and check that the data is “00”. 4) Select page: 6, address: 01, set data: 13, and press the PAUSE button of the adjustment remote commander. 5) Select page: 6, address: 01, set data: 15, and press the PAUSE button. (The adjustment data will be automatically input to the adjustment addresses.) 6) Select page: 6, address: 02, and check that the data is “01”. 7) Only for DCR-TRV20/TRV20E model, select page: F, address: 63, and check that the data is “00” to “0E”.

Adjusting method: 1) Set the zoom lens to the TELE end and expose a subject that is more than 500 m away (subject with clear contrast such as building, etc.). (Nearby subjects less than 500 m away should not be in the screen.) 2) Select page: 0, address: 01, and set data: 01. 3) Select page: 6, address: 02, and check that the data is “00”. 4) Select page: 6, address: 01, set data: 13, and press the PAUSE button of the adjustment remote commander. Note: Don’t touch the zoom lever. If you touch the zoom lever, the zoom center adjustment data will be rewritten in the value which isn’t correct.

5) 6)

Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Turn off the power and turn on again. 3) Perform “Flange Back Adjustment (2)”.

7)

Place a ND filter on the lens so that the optimum image is obtain. Select page: 6, address: 01, set data: 29, and press the PAUSE button. (The adjustment data will be automatically input to the adjustment addresses.) Select page: 6, address: 02, and check that the data is “01”.

Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 0, address: 01, and set data: 00. 3) Turn off the power and turn on again. 4) Perform “Flange Back Check”.

5-24

9. Flange Back Check Subject Siemens star (2.0m from the front of the lens) (Luminance : approx. 200 lux) Measurement Point Measuring Instrument

Check operation on TV monitor

Specified Value

Focused at the TELE end and WIDE end.

Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF 4) STEADY SHOT (Menu display) ..................................... OFF Note: When the auto focus is ON, the lens can be checked if it is focused or not by observing the data on the page 1 of the adjustment remote commander. 1) Select page: 6, address: 04, and set data: 0F. 2) Page 1 shows the state of the focus. 1 : 00 : XX Focused [ Odd: Even: Unfocused

Checking method: 1) Place the Siemens star 2.0m from the front of the lens. 2) To open the IRIS, decrease the luminous intensity to the Siemens star up to a point before noise appear on the image. 3) Shoot the Siemens star with the zoom TELE end. 4) Turn on the auto focus. 5) Check that the lens is focused (Note). 6) Select page: 6, address: 21, and set data: 10. 7) Shoot the Siemens star with the zoom WIDE end. 8) Observe the TV monitor and check that the lens is focused. Processing after Completing Adjustments: 1) Select page: 6, address: 21, and set data: 00. 2) Select page: 6, address: 04, and set data: 00.

5-25

10. Optical Axis Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) Align the lens Optical Axis with that of the CCD imager. If deviated, center of picture can lose focus when zoom is operated from the WIDE end to the TELE end. Subject Siemens star Measurement Point Measuring Instrument

Check on the monitor TV

Adjustment Page Adjustment Address

F 69

Note: NTSC model: DCR-TRV6/TRV11 PAL model: DCR-TRV6E/TRV11E

Area

1

E D0, DE

2

Switch setting: 1) POWER .................................................................. CAMERA

3

Preparations before adjustments: 1) Playback the monoscope segment of the system check tape (XH5-5 (NTSC), XH5-5P (PAL)). 2) Attach the optical axis frame chart (transparent) on the monitor TV screen. Center of monoscope image and that that of optical axis frame must be agree. 3) Set to the camera mode.

4 5 6 7

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 40, and set data: 02. 3) Select page: 6, address: 41, and set data: 01. 4) Input the data of Table 5-1-9 to each adjustment addresses.

8

00

22.6° to 67.5° 67.6° to 112.5° 112.6° to 157.5° 157.6° to 202.5° 202.6° to 247.5° 247.6° to 292.5° 292.6° to 337.5° 337.6° to 22.5°

Connection data Page: F Page: E Address: 69 Address: D0 Address: DE NTSC PAL NTSC PAL 01 22 26 57 69 02

22

26

5F

71

03

22

26

67

79

04

02

26

69

7D

05

22

26

67

79

06

22

26

5F

71

07

22

26

57

69

08

02

26

55

65

Table. 5-1-11.

Note: Press the PAUSE button each time to set the data.

Page: F Address: 69

Display phase

Processing after Completing Adjustments: 1) Select page: 0, address: 01, and set data: 00. 2) Select page: 6, address: 40, and set data: 00. 3) Select page: 6, address: 41, and set data: 00.

Page: E Address: D0 Address: DE NTSC PAL NTSC PAL 22 26 5F 71

Table. 5-1-10. 5) 6) 7)

Place the Siemens star 2.0 m away from the front of the lens. Shoot the Siemens star with the zoom TELE end. Point the lens toward the Siemens star chart until center of the Siemens star is located in the center of the optical axis frame. 8) Shoot the Siemens star with the zoom WIDE end. 9) Measure on the monitor TV screen in which area of the optical axis frame the center of the Siemens star is located. Measure the amount of displacement (distance between the center of the Siemens star and the center of the optical axis frame.) The measurement value is named L1. 10) Read the correction data corresponding to the area from Table 5-1-10. 11) Input the correction data to each adjustment address. Note: Press the PAUSE button each time to set the data.

12) Shoot the Siemens star with the zoom TELE end. 13) Point the lens toward the Siemens star chart until center of the Siemens star is located in the center of the optical axis frame. 14) Shoot the Siemens star with the zoom WIDE end. 15) Measure the amount of displacement (distance between the center of the Siemens star and the center of the optical axis frame.) The measurement value is named L2. 16) Compare the values L1 and L2, and confirm that L2 is smaller than L1. If L2 is lager than L1, input the data of Table 5-1-9 to each adjustment address.

Fig. 5-1-8.

Note: Press the PAUSE button each time to set the data.

5-26

11. Picture Frame Setting Subject Color bar chart (Color reproduction adjustment frame) (1.5m from the front of the lens) Measurement Point Measuring Instrument

Video output terminal Oscilloscope and TV monitor

Specified Value

A=B, C=D, E=F

Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF 4) STEADY SHOT (Menu display) ..................................... OFF Setting method: 1) Adjust the zoom and the camera direction, and set to the specified position. 2) Mark the position of the picture frame on the monitor display, and adjust the picture frame to this position in following adjustments using “Color reproduction adjustment frame”.

Check on the oscilloscope 1. Horizontal period A=B

C=D

B

C

A

D

Fig. 5-1-9. 2. Vertical period E=F

E

F

V

Fig. 5-1-10. Check on the monitor TV (Underscanned mode)

Color bar chart picture frame

Monitor TV picture frame

Fig. 5-1-11.

5-27

12. Color Reproduction Adjustment Adjust the color Separation matrix coefficient so that proper color reproduction is produced. Subject Color bar chart (Color reproduction adjustment frame) Measurement Point Measuring Instrument

Video output terminal Vectorscope

Adjustment Page Adjustment Address

F 35, 37, 3C, 3D

Specified Value

All color luminance points should settle within each color reproduction frame.

For DCR-TRV6/TRV11 (NTSC)

Note: NTSC model: DCR-TRV6/TRV11/TRV20 PAL model: DCR-TRV6E/TRV11E/TRV20E

Burst position

For DCR-TRV6E/TRV11E (PAL)

Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF 4) STEADY SHOT (Menu display) ..................................... OFF

Burst position

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: F, address: 8E, set the following data and press the PAUSE button. 29: DCR-TRV6/TRV6E/TRV11/TRV11E 14: DCR-TRV20/TRV20E 3) Select page: F, address: C0, set the following data and press the PAUSE button. 37: NTSC model B7: PAL model 4) Select page: 6, address: 01, set data: 3D, and press the PAUSE button. 5) Adjust the GAIN and PHASE of the vectorscope, and adjust the burst luminance point to the burst position of the color reproduction frame. 6) Change the data of page: F, address: 35, 37, 3C and 3D, and settle each color luminance point in each color reproduction frame.

For DCR-TRV20 (NTSC)

Note: Be sure to press the PAUSE button of the adjustment remote commander before changing the addresses. If not, the new data will not be written to the memory.

Processing after Completing Adjustments: 1) Select page: F, address: 8E, set the following data, and press the PAUSE button. 2E: DCR-TRV6/TRV6E/TRV11/TRV11E 17: DCR-TRV20 14: DCR-TRV20E 2) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 3) Select page: 0, address: 01, and set data: 00.

Burst position

For DCR-TRV20E (PAL) Burst position

Fig. 5-1-12.

5-28

14. Auto White Balance & LV Standard Data Input Subject Clear chart (Color reproduction adjustment frame)

13. MAX GAIN Adjustment Setting the minimum illumination. If it is not consistent, the image level required for taking subjects in low illuminance will not be produced (dark). 13-1. MAX GAIN Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) Subject Clear chart (Color reproduction adjustment frame) Adjustment Page Adjustment Address

F 1D

F 1E, 1F, 30 to 33

Specified Value

0FF0 to 1010

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 01, set data: 11, and press the PAUSE button of the adjustment remote commander. 3) Select page: 6, address: 01, set data: 0D, and press the PAUSE button. (When the standard data is take in, the data will be automatically input to page: F, address: 1E, 1F, 30 to 33.) 4) Select page: 6, address: 02, and check that the data is “01”. 5) Select page: F, address: 10, set data: 2E, and press the PAUSE button. 6) Select page: 1, and check that the display data (Note3) satisfies the specified value.

Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 97, and set data: 00. 3) Select page: 0, address: 01, and set data: 00.

13-2. MAX GAIN Data Input (DCR-TRV20/TRV20E) Adjustment Page F

Processing after Completing Adjustments: 1) Select page: F, address: 10, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 3) Select page: 0, address: 01, and set data: 00. 4) Perform “Auto White Balance Adjustment”.

1D, 8C, 9E, 9F

Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Input the following data to each address. Note: Press the PAUSE button of the adjustment remote commander each time to set the data.

3)

Adjustment Page Adjustment Address

Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 96, and set data: 00. 3) Select page: 6, address: 97, and set data: 27. 4) Select page: 6, address: 01, set data: 6F, and press the PAUSE button of the adjustment remote commander. (The MAX GAIN adjustment is performed and the adjustment data is stored in page: F, address: 1D.) 5) Select page: 6, address: 02, and check that the data is “01”.

Address 1D 8C 9E 9F

Display data of page 1 (Note3) Adjustment remote commander

Note1: This adjustment should be carried out upon completion of “Color Reproduction Adjustment”. Note2: Check that the data of page: 6, address: 02 is “00”. If not, turn off the power and turn on again. Note3: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX Display data

Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) STEADY SHOT (Menu display) ..................................... OFF

Adjustment Address

Measurement Point Measuring Instrument

Data 80 02 00 00

Select page: 0, address: 01, and set data: 00.

5-29

15. Auto White Balance Adjustment Adjust to the proper auto white balance output data. If it is not correct, auto white balance and color reproducibility will be poor. Subject Clear chart (Color reproduction adjustment frame) Filter Measurement Point

Filter C14 for color temperature correction Display data of page 1 (Note2)

Measuring Instrument Adjustment Page

Adjustment remote commander F

Adjustment Address Specified Value

40, 41 DCR-TRV6/TRV11: R ratio: 2B00 to 2C00 B ratio: 5B00 to 5C00 DCR-TRV6E/TRV11E: R ratio: 2D00 to 2E00 B ratio: 5B00 to 5C00 DCR-TRV20/TRV20E: R ratio: 2C30 to 2D30 B ratio: 5F20 to 6020

Note1: Perform “Auto White Balance & LV Standard Data Input” before this adjustment. Note2: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX Display data

Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF

Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 04, and set data: 00. 3) Select page: 0, address: 01, and set data: 00.

Adjusting method: 1) Place the C14 filter for color temperature correction on the lens. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: F, address: 42 to 45, and note down the data of each address. 4) Input the following data to page: F, addresses: 42 to 45. Address 42 43 44 45 Data 2B 80 5B 80 DCR-TRV6/TRV11 2D 80 5B 80 DCR-TRV6E/TRV11E 2C B0 5F A0 DCR-TRV20/TRV20E Note: Press the PAUSE button each time to set the data.

5) 6)

7) 8) 9) 10) 11) 12) 13)

Select page: 6, address: 01, set data: 83, and press the PAUSE button. Select page: 6, address: 01, set data: 81, and press the PAUSE button. (The auto white balance adjustment is performed and the adjustment data is stored in page: F, address: 40 and 41.) Select page: 6, address: 02, and check that the data is “01”. Select page: 6, address: 01, set data: 3F, and press the PAUSE button. Select page: 6, address: 04, and set data: 04. Select page: 1, and check that the display data (Note2) satisfies the R ratio specified value. Select page: 6, address: 04, and set data: 05. Select page: 1, and check that the display data (Note2) satisfies the B ratio specified value. Select page: F, address: 42 to 45, and input the data noted down at step 3). Note: After setting each data, be sure to press the PAUSE button of the adjustment remote commander.

5-30

16. White Balance Check Subject Clear chart (Color reproduction adjustment frame) Filter

Measurement Point

Filter C14 for color temperature correction ND filter 1.0 and 0.4 and 0.1 Video output terminal

Measuring Instrument Specified Value

Vectorscope Fig. 5-1-13. A to C

17. Mechanical Shutter Adjustment Adjust the period which the mechanical shutter is closed, and compensate the exposure. 17-1. Mechanical Shutter Data Input (DCR-TRV6/TRV6E/TRV11/TRV11E) Adjustment Page F 7 Adjustment Address

23 to 26

Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Input the following data to page: F, addresses: 70 to 84.

Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF

Note: Press the PAUSE button of the adjustment remote commander each time to set the data.

Address 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 83 84

Checking method: 1) Check that the lens is not covered with either filter. 2) Select page: 6, address: 01, set data: 0F, and press the PAUSE button of the adjustment remote commander. 3) Check that the center of the white luminance point is within the circle shown Fig. 5-1-13. (A). 4) Select page: 6, address: 01, set data: 23, and press the PAUSE button. 5) Place the C14 filter on the lens. 6) Check that the center of the white luminance point settles in the circle shown Fig. 5-1-13. (B). 7) Remove the C14 filter, and place the ND filter 1.5 (1.0+0.4+0.1) on the lens. 8) Check that the white luminance point stopped moving, and then remove the ND filter 1.5. 9) Check that the center of the white luminance point settles within the circle shown Fig. 5-1-13. (C). Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2mm

R-Y

70 to 84

B-Y

3)

Data C4 0E 75 0C 26 0B 35 0A 6E 09 A5 61 A1 79 64 81 82 84 B5 7B 20

Input the following data to page: 7, addresses: 23 to 26. Note: Press the PAUSE button of the adjustment remote commander each time to set the data.

2mm

Address 23 24 25 26

Fig. 5-1-13. (A) R-Y

1.0mm

B-Y 1.0mm

4)

3mm

3mm

Fig. 5-1-13. (B) 3mm

R-Y

3mm 2.0mm B-Y 1.0mm

Fig. 5-1-13. (C)

5-31

Data 7C 7F 7C 7B

Select page: 0, address: 01, and set data: 00.

17-2. Mechanical Shutter Data Input (DCR-TRV20/TRV20E) Adjustment Page F Adjustment Address

70 to 84

18. Angular Velocity Sensor Sensitivity Adjustment • This adjustment is performed only when replacing the angular velocity sensor. Although this adjustment need not be performed when the circuit is damaged, etc., check the operations. • Note down the sensitivity displayed on the angular velocity sensor of the repair parts. At this time, note down also to which board it was attached to. Be sure to check because if attached incorrectly, the screen will vibrate up and down or left and right during hand-shake correction operations.

7 23 to 26

Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Input the following data to page: F, addresses: 70 to 84. Note: Press the PAUSE button of the adjustment remote commander each time to set the data.

Address 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 83 84 3)

Data 81 0B 94 09 66 08 84 07 9B 05 25 43 44 4A 44 47 52 3F 44 30 21

Precautions on the Parts Replacement There are two types of repair parts. Type A: ENC03JA Type B: ENC03JB Replace the broken sensor with a same type sensor. If replace with other type parts, the image will vibrate up and down or left and right during hand-shake correction operations. After replacing, readjust according to the adjusting method after replacement. Precautions on Angular Velocity Sensor The sensor incorporates a precision oscillator. Handle it with care as if it dropped, the balance of the oscillator will be disrupted and operations will not be performed properly.

66, 67

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Read the sensor sensitivity written on SE3051 (PITCH sensor) of the JK-188 board, and take this as S3051. 3) Read the sensor sensitivity written on SE3052 (YAW sensor) of the JK-188 board, and take this as S3052. 4) Calculate D66' and D67' using the following equation (decimal calculation). DCR-TRV6/TRV11 (NTSC model) D66' = 54 / S3051 D67' = 61 / S3052 DCR-TRV6E/TRV11E (PAL model) D66' = 76 / S3051 D67' = 72 / S3052 DCR-TRV20 (NTSC model) D66' = 53 / S3051 D67' = 53 / S3052 DCR-TRV20E (PAL model) D66' = 60 / S3051 D67' = 60 / S3052 5) Convert D66' and D67' into hexadecimal digits, to obtain D66 and D67. (Round off decimal points) 6) Select page: F, address: 66, set data: D66, and press the PAUSE button of the adjustment remote commander. 7) Select page: F, address: 67, set data: D67, and press the PAUSE button of the adjustment remote commander.

Note: Press the PAUSE button of the adjustment remote commander each time to set the data.

4)

F

Adjustment Address

Note1: The sensor sensitivity of SE3051 and SE3052 of the JK-188 board is written only on the repair parts.

Input the following data to page: 7, addresses: 23 to 26.

Address 23 24 25 26

Adjustment Page

Data 7A 80 80 82

Select page: 0, address: 01, and set data: 00.

Processing after Completing Adjustments 1) Select page: 0, address: 01, and set data: 00. 2) Check that the steady shot operations have been performed normally.

5-32

1-4.

1. VCO Adjustment (VC-240/241 board) Set the VCO free-run frequency. If deviated, the EVF screen will be blurred. Mode Camera

COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT

Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to avoid electrical shock. Note 2: When replacing the LCD unit, be careful to prevent damages caused by static electricity. Note 3: Set the VF BRIGHT (Menu display) to the center. Close the LCD panel. Note 4: As the PANEL CLOSE switch (CK-92/94 board S3201) is attached to the cabinet (R), this cabinet must be attached when performing adjustments. If you perform the adjustments with cabinet (R) removed, set the following data. 1) Select page: 2, address: 0E, and set data: 67. 2) Select page: 2, address: 0F, and set data: 01. Reset the data after completing adjustment. 1) Select page: 2, address: 0E, and set data: 00. 2) Select page: 2, address: 0F, and set data: 00. Note 5: CK-92 board: DCR-TRV11/TRV11E/TRV20 CK-94 board: DCR-TRV6/TRV6E/TRV20E VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E

Signal Name LANC SIG EVF BL – EVF VCO PANEL VG H START PANEL COM TCK JIG TDO SWP GND

Pin No. 2 4 6 8 10 12 14 16 18 20

19

20

Frequency counter D

Adjustment Address Specified Value

92, 93 f = 15734 ± 30Hz (NTSC) f = 15625 ± 30Hz (PAL)

Note: The VCO adjustment mode is set up automatically, so the EVF screen falls into the disorder.

3) 4) 5)

Signal Name EVF BL + EVF VG GND PD VCO XHD/PSIG TMS JIG TDI GND RF IN/LANC JACK IN RF MON

CN009 2

Measuring Instrument Adjustment Page

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 92, change the data and set the VCO frequency (f) to the specified value.

Table. 5-1-12.

1

Arbitrary Pin 5 of CN009 (VCO)

Note: NTSC model: DCR-TRV6/TRV11/TRV20 PAL model: DCR-TRV6E/TRV11E/TRV20E

[Adjusting connector] Most of the measuring points for adjusting the viewfinder system are concentrated in CN009 of the VC-240/241 board. Connect the Measuring Instruments via the CPC-8 jig (J-6082-388-A). The following table shows the Pin No. and signal name of CN009. Pin No. 1 3 5 7 9 11 13 15 17 19

Subject Measurement Point

Remove the CPC lid

Fig. 5-1-14.

5-33

Press the PAUSE button of the adjustment remote commander. Select page: D, address: 93, set the same data as page: D, address: 92, and press the PAUSE button. Select page: 0, address: 01, and set data: 00.

3. Contrast Adjustment (VC-240/241 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated (whitish). Mode Camera

2. RGB AMP Adjustment (VC-240/241 board) Set the D range of the RGB decoder used to drive the LCD to the specified value. If deviated, the LCD screen will become blackish or saturated (whitish). Mode Camera Subject Measurement Point

Arbitrary Pin 4 of CN009 (EVF VG)

Subject Measurement Point

Arbitrary Pin 4 of CN009 (EVF VG)

Measuring Instrument Adjustment Page

Oscilloscope D

Measuring Instrument Adjustment Page

Oscilloscope D

Adjustment Address Specified Value

95 A = 7.00 ± 0.05V

Adjustment Address Specified Value

99 DCR-TRV20/TRV20E: A=2.40 ± 0.05V DCR-TRV6/TRV6E/TRV11/TRV11E: A=2.20 ± 0.05V

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 95, change the data and set the voltage (A) between the reversed waveform pedestal and non-reversed waveform pedestal to the specified value.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 99, change the data and set the voltage (A) between the pedestal (0 IRE) and 100 IRE to the specified value. (The data of address: 99 should be “00” to “7F”.)

Note: The RGB AMP adjustment mode is set up automatically, so the 3 steps signal is displayed on the EVF screen.

3) 4)

Press the PAUSE button. Select page: 0, address: 01, and set data: 00.

Note: The contrast adjustment mode is set up automatically, so the 3 steps signal is displayed on the EVF screen.

3) 4)

Pedestal

Press the PAUSE button. Select page: 0, address: 01, and set data: 00.

A

100 IRE

A

2H

2H

Pedestal

Pedestal

Fig. 5-1-15.

Fig. 5-1-16.

5-34

5. White Balance Adjustment (VC-240/241 board) Correct the white balance. If deviated, the reproduction of the EVF screen may degenerate. Mode Camera

4. Backlight Consumption Current Adjustment (VC-240/241 board) Set the backlight luminance and color temperature. If deviated, the image may become dark or bright. Mode Camera Subject Measurement Point

Arbitrary + Probe: Pin 2 of CN009 (EVF BL+) − Probe: Pin 3 of CN009 (EVF BL−)

Measuring Instrument Adjustment Page

Digital voltmeter D

Adjustment Address Specified Value

9C, 9D, 9E DCR-TRV20/TRV20E: BRIGHT mode : A=25.0 ± 1.5mVdc NORMAL mode : A=15.0 ± 1.5mVdc DCR-TRV6/TRV6E/TRV11/TRV11E: BRIGHT mode : A=17.0 ± 1.5mVdc NORMAL mode : A=10.0 ± 1.5mVdc

3)

9E 11

6)

97, 98 The EVF screen should not be colored.

3)

9F 1F

97 80

98 80

Check that the EVF screen is not colored. If colored, change the data of page: D, address: 97 and 98 so that the EVF screen is not colored. Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data.

Select page: D, address: 9D, change the data and set the voltage difference (A) between Pin 2 of CN009 (EVF BL+) and Pin 3 of CN009 (EVF BL−) to the specified value of BRIGHT mode. (The data of address: 9D should be “C0” to “FF”.)

4)

Press the PAUSE button of the adjustment remote commander. Select page: D, address: 9C, set the same data as page: D, address: 9D, and press the PAUSE button. Select page: D, address: 9E, change the data and set the voltage difference (A) between Pin 2 and Pin 3 to the specified value of NORMAL mode. (The data of address: 9E should be “00” to “1F”.) Note: The backlight consumption current adjustment NORMAL mode is set up automatically.

7) 8)

Adjustment Address Specified Value

Address Data

Note: The backlight consumption current adjustment BRIGHT mode is set up automatically.

4) 5)

D

Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data.

Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data.

9D E0

Measuring Instrument Adjustment Page

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 97 and 98, set the data to the initial value.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 9C to 9F, and set the data to the initial value.

9C E0

Arbitrary Check on EVF screen

Note: Check the white balance only when replacing the following parts. If necessary, adjust them. 1. LCD panel 2. Light induction plate 3. IC1802

Note1: Perform the adjustment in the following order.

Address Data

Subject Measurement Point

Press the PAUSE button. Select page: 0, address: 01, and set data: 00.

5-35

When address: 97 or 98 is selected, the white balance adjustment mode is set up automatically. Select page: 0, address: 01, and set data: 00.

1-5.

1-5-1.

LCD SYSTEM ADJUSTMENT

Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to avoid electrical shock. Note 2: When replacing the LCD unit, be careful to prevent damages caused by static electricity. Note 3: Set the LCD BRIGHT to the center. Set the LCD COLOR (Menu display) to the center. Note 4: PD-123 board: DCR-TRV11/TRV11E/TRV20 PD-124 board: DCR-TRV6/TRV6E/TRV20E VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E

1. VCO Adjustment (PD-123 board) Set the VCO free-run frequency. If deviated, the LCD screen will be blurred. Mode Camera

[Adjusting connector] Most of the measuring points for adjusting the LCD system are concentrated in CN009 of the VC-240/241 board. Connect the Measuring Instruments via the CPC-8 jig (J-6082-388A). The following table shows the Pin No. and signal name of CN009. Pin No. 1 3 5 7 9 11 13 15 17 19

Signal Name Pin No. LANC SIG 2 EVF BL – 4 EVF VCO 6 PANEL VG 8 H START 10 PANEL COM 12 TCK 14 JIG TDO 16 SWP 18 GND 20 Table. 5-1-13.

2

19

20

Subject Measurement Point

Arbitrary Pin 9 of CN009 (H START) of VC-240/241 board

Measuring Instrument Adjustment Page

Frequency counter D

Adjustment Address Specified Value

A2, A3 f = 15734 ± 30Hz (NTSC) f = 15625 ± 30Hz (PAL)

Note: NTSC: DCR-TRV11/TRV20 PAL: DCR-TRV11E

Signal Name EVF BL + EVF VG GND PD VCO XHD/PSIG TMS JIG TDI GND RF IN/LANC JACK IN RF MON

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A2, change the data and set the VCO frequency (f) to the specified value. Note: The VCO adjustment mode is set up automatically, so the LCD screen falls into the disorder.

3) 4) 5)

CN009 1

LCD SYSTEM ADJUSTMENT (DCR-TRV11/TRV11E/TRV20)

Remove the CPC lid

Fig. 5-1-17.

5-36

Press the PAUSE button of the adjustment remote commander. Select page: D, address: A3, set the same data as page: D, address: A2, and press the PAUSE button. Select page: 0, address: 01, and set data: 00.

3. Contrast Adjustment (PD-123 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated (whitish). Mode Camera

2. RGB AMP Adjustment (PD-123 board) Set the D range of the RGB decoder used to drive the LCD to the specified value. If deviated, the LCD screen will become blackish or saturated (whitish). Mode Camera Subject Measurement Point

Arbitrary Pin 7 of CN009 (PANEL VG) of VC-240/241 board Ext. trigger: Pin qa of CN009 (PANEL COM)

Subject Measurement Point

Arbitrary Pin 7 of CN009 (PANEL VG) of VC-240/241 board Ext. trigger: Pin qa of CN009 (PANEL COM)

Measuring Instrument Adjustment Page

Oscilloscope D

Measuring Instrument Adjustment Page

Oscilloscope D

Adjustment Address Specified Value

A5 A = 3.70 ± 0.05V (LCD TYPE SH NTSC) A = 3.45 ± 0.05V (LCD TYPE SH PAL) A = 3.50 ± 0.05V (LCD TYPE CA)

Adjustment Address Specified Value

AA A = 3.30 ± 0.05V (LCD TYPE SH NTSC) A = 3.25 ± 0.05V (LCD TYPE SH PAL) A = 3.45 ± 0.05V (LCD TYPE CA)

Note: LCD TYPE SH NTSC: DCR-TRV11 LCD TYPE SH PAL: DCR-TRV11E LCD TYPE CA: DCR-TRV20

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: AA, change the data and set the voltage (A) between the pedestal (0 IRE) and 100 IRE to the specified value. (The data of address: AA should be “00” to “7F”.)

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A5, change the data and set the voltage (A) between the reversed waveform pedestal and non-reversed waveform pedestal to the specified value. (The data of address: A5 should be “00” to “3F”.)

Note: The contrast adjustment mode is set up automatically, so the 3 steps signal is displayed on the LCD screen.

3) 4)

Press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00.

Note: The RGB AMP adjustment mode is set up automatically, so the 3 steps signal is displayed on the LCD screen.

3) 4)

Press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00. Pedestal

100IRE

A

A

2H

2H

Pedestal

Pedestal

Fig. 5-1-18.

Fig. 5-1-19.

5-37

Ver 1.1 2000. 06

4. V-COM Level Adjustment (PD-123 board) Set the common electrode drive signal level of LCD to the specified value. Mode Camera Subject Measurement Point

5. V-COM Adjustment (PD-123 board) Set the DC bias of the common electrode drive signal of LCD to the specified value. If deviated, the LCD display will move, producing flicker and conspicuous vertical lines. Mode Camera

Arbitrary Pin qa of CN009 (PANEL COM) of VC-240/241 board

Measuring Instrument Adjustment Page

Oscilloscope D

Adjustment Address Specified Value

A7 A = 6.00 ± 0.05V (LCD TYPE SH) A = 5.70 ± 0.05V (LCD TYPE CA)

Arbitrary Check on LCD display

Measuring Instrument Adjustment Page

D

Adjustment Address Specified Value

Note: Perform “RGB AMP Adjustment” and “Contrast Adjustment” before this adjustment.

A4 The brightness difference between the section A and section B is minimum.

Note: Perform “RGB AMP Adjustment”, “Contrast Adjustment” and “VCOM Level Adjustment” before this adjustment.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A7, change the data and set the PANEL COM signal level (A) to the specified value.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A4, change the data so that the brightness of the section A and that of the section B is equal.

Note: The V-COM level adjustment mode is set up automatically.

3) 4)

Subject Measurement Point

Press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00.

Note: The V-COM adjustment mode is set up automatically, so the V COM adjustment signal is displayed on the LCD screen.

3) 4)

A

2H

Subtract 8 from the data of page: D, address: A4, and press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00.

B

A

A

B

B

A

A

B

Fig. 5-1-20. Fig. 5-1-21.

5-38

1-5-2.

6. White Balance Adjustment (PD-123 board) Correct the white balance. If deviated, the reproduction of the LCD screen may degenerate. Mode Camera Subject Measurement Point

Arbitrary Check on LCD screen

Measuring Instrument Adjustment Page

D

Adjustment Address Specified Value

A8, A9 The LCD screen should not be colored.

1. VCO Adjustment (PD-124 board) Set the VCO free-run frequency. If deviated, the LCD screen will be blurred. Mode VTR stop

Note: Check the white balance only when replacing the following parts. If necessary, adjust them. 1. LCD panel 2. Light induction plate 3. IC2104

3)

Measuring Instrument Adjustment Page

Frequency counter D

Adjustment Address Specified Value

A2, A3 f = 15734 ± 30Hz (NTSC) f = 15625 ± 30Hz (PAL)

Note: The VCO adjustment mode is set up automatically, so the LCD screen falls into the disorder.

A9 87

3) 4)

Check that the LCD screen is not colored. If colored, change the data of page: D, address: A8 and A9 so that the LCD screen is not colored.

5)

Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data. When address: A8 or A9 is selected, the white balance adjustment mode is set up automatically.

4)

No signal Pin 9 of CN009 (H START) of VC-240/241 board

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A2, change the data and set the VCO frequency (f) to the specified value.

Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data.

A8 7F

Signal Measurement Point

Note: NTSC: DCR-TRV6 PAL: DCR-TRV6E/TRV20E

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A8 and A9, set the data to the initial value.

Address Data

LCD SYSTEM ADJUSTMENT (DCR-TRV6/TRV6E/TRV20E)

6)

Select page: 0, address: 01, and set data: 00.

7) 8)

5-39

Press the PAUSE button of the adjustment remote commander. Select page: D, address: A2, read the data, and this data is named DA2. Convert DA2 to decimal notation, and obtain DA2'. (Refer to Table 5-4-1. Hexadecimal-decimal Conversion Table.) Calculate DA3' using following equations (Decimal calculation), convert it to a hexadecimal number, and input to address: A3. DCR-TRV6: DA3' = DA2' + 38 DCR-TRV6E: DA3' = DA2' - 38 DCR-TRV20E: DA3' = DA2' - 11 Press the PAUSE button. Select page: 0, address: 01, and set data: 00.

2. Bright Adjustment (PD-124 board) Set the D range of the RGB decoder used to drive the LCD to the specified value. If deviated, the LCD screen will become blackish or saturated (whitish). Mode VTR stop

3. Black Limit Adjustment (PD-124 board) Set the dynamic range of the LCD driver to an appropriate level. If deviated, the LCD screen will become blackish or saturated (whitish). Mode VTR stop

Signal Measurement Point

No signal Pin 7 of CN009 (PANEL VG) of VC-240/241 board

Signal Measurement Point

No signal Pin 0 of CN009 (PSIG) of VC-240/241 board

Measuring Instrument Adjustment Page

Oscilloscope D

Measuring Instrument Adjustment Page

Oscilloscope D

Adjustment Address Specified Value

A5 A = 7.6 ± 0.05V

Adjustment Address Specified Value

A6 A = 8.00 ± 0.05V

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 0C, set data: 20, and press the PAUSE button of the adjustment remote commander. 3) Select page: 3, address: 22, set data: 08, and press the PAUSE button. 4) Select page: D, address: A5, change the data and set the voltage (A) between the reversed waveform pedestal and non-reversed waveform pedestal to the specified value. 5) Press the PAUSE button. 6) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 7) Select page: 3, address: 22, set data: 00, and press the PAUSE button. 8) Select page: 0, address: 01, and set data: 00.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 0E, and set data: 61. 3) Select page: 2, address: 0F, and set data: 5B (*1) or 53 (*2). *1: DCR-TRV6 *2: DCR-TRV6E/TRV20E 4) Select page: D, address: A6, change the data and set the PSIG signal amplitude (A) to the specified value. (The data of address: A6 should be “00” to “0F”.) 5) Press the PAUSE button of the adjustment remote commander. 6) Select page: 2, address: 0E, and set data: 00. 7) Select page: 2, address: 0F, and set data: 00. 8) Select page: 0, address: 01, and set data: 00.

Pedestal

A

A

V

Fig. 5-1-23. 2H Pedestal

Fig. 5-1-22.

5-40

5. Center Level Adjustment (PD-124 board) Set the video signal center level of LCD panel to an appropriate level. Mode VTR stop

4. Contrast Adjustment (PD-124 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated (whitish). Mode VTR stop Signal Measurement Point

No signal Pin 7 of CN009 (PANEL VG) of VC-240/241 board Ext. trigger: Pin qa of CN009 (PANEL COM)

Measuring Instrument Adjustment Page

Oscilloscope D

Adjustment Address Specified Value

AA A = 2.80 ± 0.05V (TRV6E/TRV20E) A = 2.60 ± 0.05V (TRV6)

No signal Pin 7 of CN009 (PANEL VG) of VC-240/241 board

Measuring Instrument Adjustment Page

Digital voltmeter D

Adjustment Address Specified Value

AB A = 5.25 ± 0.03V (3.5" LCD) A = 6.75 ± 0.03V (2.5" LCD)

Note: 3.5" LCD: DCR-TRV20E 2.5" LCD: DCR-TRV6/TRV6E

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 0C, set data: 20, and press the PAUSE button of the adjustment remote commander. 3) Select page: 3, address: 22, set data: 08, and press the PAUSE button. 4) Select page: D, address: AB, change the data and set the DC voltage (A) of VG signal to the specified value. 5) Press the PAUSE button. 6) Select page: 3, address: 22, set data: 00, and press the PAUSE button. 7) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 8) Select page: 0, address: 01, and set data: 00.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: AA, change the data and set the voltage (A) between the pedestal (0 IRE) and 100 IRE to the specified value. (The data of address: AA should be “00” to “7F”.) Note: The contrast adjustment mode is set up automatically, so the 3 steps signal is displayed on the LCD screen.

3) 4)

Signal Measurement Point

Press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00.

100IRE

A

2H Pedestal

Fig. 5-1-24.

5-41

7. White Balance Adjustment (PD-124 board) Correct the white balance. If deviated, the reproduction of the LCD screen may degenerate. Mode VTR stop

6. V-COM Adjustment (PD-124 board) Set the DC bias of the common electrode drive signal of LCD to the specified value. If deviated, the LCD display will move, producing flicker and conspicuous vertical lines. Mode VTR stop Signal Measurement Point

No signal Check on LCD display

Measuring Instrument Adjustment Page

D

Adjustment Address Specified Value

A4 The brightness difference between the section A and section B is minimum.

Measuring Instrument Adjustment Page

D

Adjustment Address Specified Value

A8, A9 The LCD screen should not be colored.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A8 and A9, set the data to the initial value.

Note: The V-COM adjustment mode is set up automatically, so the V COM adjustment signal is displayed on the LCD screen.

5)

No signal Check on LCD screen

Note: Check the white balance only when replacing the following parts. If necessary, adjust them. 1. LCD panel 2. Light induction plate 3. IC3101

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A4, change the data so that the brightness of the section A and that of the section B is equal. (The data of address: A4 should be “00” to “3F”.) 3) 4)

Signal Measurement Point

Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data.

Press the PAUSE button of the adjustment remote commander. Select page: D, address: A4, substract 1 (TRV20E) or 3 (TRV6/ TRV6E) from the data, and press the PAUSE button. Select page: 0, address: 01, and set data: 00.

Address Data 3)

B

A

A

B

B

A

A9 72

Check that the LCD screen is not colored. If colored, change the data of page: D, address: A8 and A9 so that the LCD screen is not colored. Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data. When address: A8 or A9 is selected, the white balance adjustment mode is set up automatically.

4) A

A8 8A

B

Fig. 5-1-25.

5-42

Select page: 0, address: 01, and set data: 00.

5-2. MECHANISM SECTION ADJUSTMENT On the mechanism section adjustment For details of mechanism section adjustments, checks, and replacement of mechanism parts, refer to the separate volume “DV MECHANICAL ADJUSTMENT MANUAL J Mechanism ”.

2-1.

1) 2) 3) 4)

2-3.

Note: Only for the DCR-TRV20/TRV20E model, the lens block (CD-252 board) must be connected when performing the adjustments.

1. Preparation for Adjustment 1) Clean the tape running side (tape guide, drum, capstan shaft, pinch roller, etc.). 2) Connect the adjustment remote commander to the LANC jack. 3) Turn the HOLD switch of the adjustment remote commander to the ON position. 4) Connect an oscilloscope to VC-240/241 board CN009 via the CPC-8 jig (J-6082-388-A). Channel 1: VC-240/241 board, CN009 Pin w; (Note) External trigger: VC-240/241 board, CN009 Pin qj

HOW TO ENTER RECORD MODE WITHOUT CASSETTE

Connect the adjustment remote commander to the LANC jack. Turn the HOLD switch of the adjustment remote commander to the ON position. Close the cassette compartment without the cassette. Select page: 3, address: 01, set data: 0C, and press the PAUSE button of the adjustment remote commander. (The mechanism enters the record mode automatically.)

Note: Connect a 75 Ω resistor between pins w; of CN009 and ql (GND). 75 Ω resistor (Parts code: 1-247-804-11)

Note: The function buttons become inoperable.

5)

To quit the record mode, select page: 3, address: 01, set data: 00, and press the PAUSE button of the adjustment remote commander. (Whenever you want to quit the record mode, be sure to quit following this procedure.)

2-2.

1) 2) 3) 4)

5) 6) 7) 8)

HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE

Connect the adjustment remote commander to the LANC jack. Turn the HOLD switch of the adjustment remote commander to the ON position. Close the cassette compartment without the cassette. Select page: 3, address: 01, set data: 0B, and press the PAUSE button of the adjustment remote commander. (The mechanism enters the playback mode automatically.)

Playback the alignment tape for tracking. (XH2-1) Select page: 3, address: 33, and set data: 08. Select page: 3, address: 26, and set data: 31. Check that the oscilloscope RF waveform is normal at the entrance and exit. If not normal, adjust according to the separate volume “DV MECHANICAL ADJUSTMENT MANUAL J Mechanism ” .

CN009 of VC-240/241 board Pin No. Signal Name Pin No. 1 LACN SIG 2 3 EVF BL– 4 5 EVF VCO 6 7 PANEL VG 8 9 H START 10 11 PANEL COM 12 13 TCK 14 15 JIG TDO 16 17 SWP 18 19 GND 20

Note: The function buttons become inoperable.

5)

TAPE PATH ADJUSTMENT

To quit the playback mode, select page: 3, address: 01, set data: 00, and press the PAUSE button of the adjustment remote commander. (Whenever you want to quit the playback mode, be sure to quit following this procedure.)

Signal Name EVF BL+ EVF VG GND PD VCO XHD/PSIG TMS JIG TDI GND RF IN/LANC JACK IN RF MON

2. Procedure after operations 1) Connect the adjustment remote commander to the LANC jack and set the HOLD switch to the ON position. 2) Select page: 3, address: 26, and set data: 00. 3) Select page: 3, address: 33, and set data: 00. Entrance side

Check this section (Normal waveform)

CH1

CH2 (Trigger) 3.3msec

Fig. 5-2-1.

5-43

Exit side

5-3. VIDEO SECTION ADJUSTMENTS NTSC model : DCR-TRV6/TRV11/TRV20 PAL model : DCR-TRV6E/TRV11E/TRV20E

3-1.

PREPARATIONS BEFORE ADJUSTMENTS

Use the following measuring instruments for video section adjustments. 3-1-1. 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11)

12) 13) 14) 15)

Equipment Required

TV monitor Oscilloscope (dual-phenomenon, band above 30 MHz with delay mode) (Unless specified otherwise, use a 10 : 1 probe.) Frequency counter Pattern generator with video output terminal. Digital voltmeter Audio generator Audio level meter Audio distortion meter Audio attenuator Regulated power supply Alignment tapes • Tracking standard (XH2-1) Parts code: 8-967-997-01 • SW/OL standard (XH2-3) Parts code: 8-967-997-11 • Audio operation check for NTSC (XH5-3) Parts code: 8-967-997-51 • System operation check for NTSC (XH5-5) Parts code: 8-967-997-61 • BIST check for NTSC (XH5-6) Parts code: 8-967-997-71 • Audio operation check for PAL (XH5-3P) Parts code: 8-967-997-55 • System operation check for PAL (XH5-5P) Parts code: 8-967-997-66 • BIST check for PAL (XH5-6P) Parts code: 8-967-997-76 Adjustment remote commander (J-6082-053-B) CPC-8 jig (J-6082-388-A) IR receiver jig (J-6082-383-A) Extension cable (80P, 0.4 mm) For extension between the DD-137 board (CN1603) and the VC-240/241 board (CN002) (J-6082-395-A)

5-44

Note 1: Setting the “Forced VTR Power ON” mode (VTR mode) 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 02, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the VTR power to be turned on with the control switch block (FK-30150 block) removed. After completing adjustments, be sure to exit the “Forced Power ON mode”. Note 2: Setting the “Forced Camera Power ON” mode (Camera mode) 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the camera power to be turned on with the control switch block (FK-30150 block) removed. After completing adjustments, be sure to exit the “Forced Power ON mode”. Note 3: Setting the “Forced Memory Power ON” mode (Memory mode) 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 05, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the memory power to be turned on with the control switch block (FK-30150 block) removed. After completing adjustments, be sure to exit the “Forced Power ON mode”. Note 4: Exiting the “Forced Power ON” mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00. Note 5: CK-92 board: DCR-TRV11/TRV11E/TRV20 CK-94 board: DCR-TRV6/TRV6E/TRV20E VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E

3-1-2. Precautions on Adjusting 1) The adjustments of this unit are performed in the VTR mode or camera mode. To set to the VTR mode, set the power switch to “VCR” (or “PLAYER”) or set the “Forced VTR Power ON mode” using the adjustment remote commander (Note 1). To set to the Camera mode, set the power switch to “CAMERA” or set the “Forced Camera Power ON mode” using the adjustment remote commander (Note 2). After completing adjustments, be sure to exit the “Forced VTR Power ON Mode” or “Forced Camera Power ON Mode”. (Note 3) 2) The front panel block (MA-385 board, microphone unit, remote commander receiver, LANC/DIGITAL I/O jack, MIC jack) must be assembled because the audio/video jack is used for connecting the monitor TV. To remove, disconnect the following connector. MA-385 board CN2071 (28P, 0.5mm) 3) Cabinet (R) (CK-92/94board, LCD block) need not be connected. But removing the cabinet (R) (removing the VC240/241 board CN003) means removing the lithium 3V power supply (CK-92/94 board, BT3201) , data such as date, time, user-set menus will be lost. After completing adjustments, reset these data. If the cabinet (R) has been removed, the selfdiagnosis data, data on history of use (total drum rotation time etc.) will be lost. Before removing, note down the self-diagnosis data and the data on the history use (data of page: 2, address: A2 to AA). (Refer to “SELF-DIAGNOSIS FUNCTION” for the self-diagnosis data, and to “5-4.Service Mode” for the data on the history use.) To remove the cabinet (R), disconnect the following connectors. VC-240/241 board CN003 (51P, 0.3mm) 4) The viewfinder (LB-64 board) is need not be connected. To remove it, disconnect the following connector. DD-137 board CN1604 (27P, 0.3mm) 5) For extension between the DD-137 board CN1603 and VC240/241 board CN002, use the following extension cable. J-6082-395-A (80P, 0.4mm) 6) Only for the DCR-TRV20/TRV20E model, the lens block (CN701 of VC-240 board) must be connected when performing adjustments, because the timing generator (IC102) is provided on the CD-252 board of the lens block.

5-45

3-1-3. Adjusting Connectors Some of the adjusting points of the video section are concentrated at VC-240/241 board CN009. Connect the measuring instruments via the CPC-8 jig (J-6082-388-A). The following table lists the pin numbers and signal names of CN009. Pin No. 1 3 5 7 9 11 13 15 17 19

Signal Name LACN SIG EVF BL– EVF VCO PANEL VG H START PANEL COM TCK JIG TDO SWP GND

Pin No. 2 4 6 8 10 12 14 16 18 20

Signal Name EVF BL+ EVF VG GND PD VCO XHD/PSIG TMS JIG TDI GND RF IN/LANC JACK IN RF MON

CN009 1

2

19

20

Remove the CPC lid

Fig. 5-3-1

Table 5-3-1.

3-1-4. Connecting the Equipment Connect the measuring instruments as shown in Fig. 5-3-2, and perform the adjustments.

VTR recording mode (Except AEP/UK model) Pattern generator Video output (75 Ω)

VIDEO (Yellow)

Adjustment remote commander

AUDIO L (White)

Main unit

AUDIO R (Red)

LANC jack

AUDIO/VIDEO jack

Playback mode

TV monitor VIDEO (Yellow) Main unit AUDIO L (White)

Adjustment remote commander

AUDIO R (Red) LANC jack

AUDIO/VIDEO jack

Fig. 5-3-2. 3-1-5. Checking the Input Signals (Except AEP/UK model) Because the video signal obtained from the pattern generator is used as the adjustment signal for adjusting the VTR section, the video output signal must satisfy the given specifications. Connect the oscilloscope to the video terminal of the AUDIO/ VIDEO jack, and check that the sync signal amplitude of the video signal is approximately [0.30V], the amplitude of the video section is approximately [0.70V], the amplitude of the burst signal is approximately [0.30V] and flat, and that the level ratio of the burst signal to the “red” signal is 0.30 : 0.60. The video signal used for adjusting the video section is shown in Fig. 5-3-3. < > : NTSC model [ ] : PAL model

5-46

3-1-6. Alignment Tapes Use the alignment tapes shown in the following table. Use tapes specified in the signal column of each adjustment. Name Tracking standard (XH2-1) SW/OL standard (XH2-3) Audio operation check (XH5-3 (NTSC), XH5-3P (PAL)) System operation check (XH5-5 (NTSC), XH5-5P (PAL)) BIST check (XH5-6 (NTSC), XH5-6P (PAL))

Use Tape path adjustment Switching position adjustment Audio system adjustment Operation check BIST check

Fig. 5-3-3 shows the 75% color bar signals recorded on the alignment tape for Audio Operation Check. Note: Measure with video terminal (Terminated at 75 Ω)

For NTSC model

Blue

Red

Magenta

Green

(75%)

1V

Cyan

Burst signal

Yellow

0.714V

White

Cyan Green Magenta Red Blue

White (75%)

Yellow

White (100%)

0.286V 0.286V

Q

Q

I

Black

I White (100%)

Horizontal sync signal Color bar signal waveform

Color bar pattern

Black

Blue

Red

Magenta

Green

Cyan

0.3V

Yellow

White

0.7V 1V

Magenta Red Blue

White (100%)

Yellow Cyan Green

For PAL model

(100%)

0.3V Burst signal

Horizontal sync signal

Color bar signal waveform

Color bar pattern

Fig. 5-3-3. Color bar signal of alignment tapes 3-1-7. Input/Output Level and Impedance Video input/output Special stereo mini jack Video signal: 1 Vp-p, 75 Ω unbalanced, sync negative S video input/output 4-pin mini DIN Luminance signal: 1 Vp-p, 75 Ω unbalanced, sync negative Chrominance signal: 0.286 Vp-p, 75 Ω unbalanced (NTSC) : 0.300 Vp-p, 75 Ω unbalanced (PAL)

Audio input/output Special stereo mini jack Input level: 327mV Input impedance: More than 47kΩ Output level: 327 mV (at load impedance 47 kΩ) Output impedance: Below 2.2 kΩ

5-47

3-2.

2-2. Serial No. Input Write the serial No. and model code in the EEPROM (nonvolatile memory). Convert the serial No. on the name plate from decimal to hexadecimal, and write in the EEPROM. Page C

SYSTEM CONTROL SYSTEM ADJUSTMENT

1. Initialization of B, C, D, E, F, 7, 8 Page Data If the B, C, D, E, F, 7, 8 page data is erased due to some reason, perform “1-2. INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE DATA”, of “5-1. CAMERA SECTION ADJUSTMENT”

Address

2. Serial No. Input 2-1. Company ID Input Write the company ID in the EEPROM (nonvolatile memory). Page C Address

Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Read the serial No. on the name plate, and take it as D1. Example: If the serial No. is 77881. D1=77881 3) Obtain D2 and H1 corresponding to D1 from Table 5-3-2. Example: If D1 is “77881”. D2=D1–65536=12345 H1=FE H1 (Hexadecimal) D1 (Decimal) D2 (Decimal) (Service model code) 000001 to 065535 D1 FE 065536 to 131071 D1–65536 FE 131072 to 196607 D1–131072 FE

E8, E9, EA, EB, EC

Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Input the following data to page: C, addresses: E8 to EC. Note: Press the PAUSE button of the adjustment remote commander each time to set the data.

Address E8 E9 EA EB EC 3)

ED, EE, EF

Data 08 00 46 01 02

Table 5-3-2. 4)

Input H1 to page: C, address: ED. (Model code input) Example: If H1 is “FE”. Select page: C, address: ED, set data: FE, and press the PAUSE button. 5) Obtain the maximum decimal not exceeding D2 from Table 53-3, and take this as D3. Example: If D2 is “12345”. D3=12288 6) Obtain the hexadecimal corresponding to D3 from Table 5-3-3, and take this as H3. Example: If D3 is “12288”. H3=3000 7) Obtain the difference D4 between D 2 and D 3. (Decimal calculation, 0 D4 255) D4= D2–D3 Example: If D2 is “12345” and D3 is “12288”. D4=12345–12288=57 8) Convert D4 to hexadecimal, and take this as H4. (Refer to “Hexadecimal-decimal conversion table” in “5-4. Service Mode”.) Example: If D4 is “57”. H4=39 9) Input the upper 2 digits of H3 to page: C, address: EE. Example: If H3 is “3000”. Select page: C, address: EE, set data: 30, and press the PAUSE button. 10) Input H4 to page: C, address: EF. Example: If H4 is “39”. Select page: C, address: EF, set data: 39, and press the PAUSE button. 11) Select page: 0, address: 01, and set data: 00.

Select page: 0, address: 01, and set data: 00.

5-48

HexaHexaHexaHexaHexaHexaHexaHexaDecimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal (D3) (D3) (D3) (D3) (D3) (D3) (D3) (D3) (H3) (H3) (H3) (H3) (H3) (H3) (H3) (H3)

0 256 512 768 1024 1280 1536 1792 2048 2304 2560 2816 3072 3328 3584 3840 4096 4352 4608 4864 5120 5376 5632 5888 6144 6400 6656 6912 7168 7424 7680 7936

0000 0100 0200 0300 0400 0500 0600 0700 0800 0900 0A00 0B00 0C00 0D00 0E00 0F00 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 1A00 1B00 1C00 1D00 1E00 1F00

8192 8448 8704 8960 9216 9472 9728 9984 10240 10496 10752 11008 11264 11520 11776 12032 12288 12544 12800 13056 13312 13568 13824 14080 14336 14592 14848 15104 15360 15616 15872 16128

2000 2100 2200 2300 2400 2500 2600 2700 2800 2900 2A00 2B00 2C00 2D00 2E00 2F00 3000 3100 3200 3300 3400 3500 3600 3700 3800 3900 3A00 3B00 3C00 3D00 3E00 3F00

16384 16640 16896 17152 17408 17664 17920 18176 18432 18688 18944 19200 19456 19712 19968 20224 20480 20736 20992 21248 21504 21760 22016 22272 22528 22784 23040 23296 23552 23808 24064 24320

4000 4100 4200 4300 4400 4500 4600 4700 4800 4900 4A00 4B00 4C00 4D00 4E00 4F00 5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 5A00 5B00 5C00 5D00 5E00 5F00

24576 24832 25088 25344 25600 25856 26112 26368 26624 26880 27136 27392 27648 27904 28160 28416 28672 28928 29184 29440 29696 29952 30208 30464 30720 30976 31232 31488 31744 32000 32256 32512

6000 6100 6200 6300 6400 6500 6600 6700 6800 6900 6A00 6B00 6C00 6D00 6E00 6F00 7000 7100 7200 7300 7400 7500 7600 7700 7800 7900 7A00 7B00 7C00 7D00 7E00 7F00

32768 33024 33280 33536 33792 34048 34304 34560 34816 35072 35328 35584 35840 36096 36352 36608 36864 37120 37376 37632 37888 38144 38400 38656 38912 39168 39424 39680 39936 40192 40448 40704

Table 5-3-3.

5-49

8000 8100 8200 8300 8400 8500 8600 8700 8800 8900 8A00 8B00 8C00 8D00 8E00 8F00 9000 9100 9200 9300 9400 9500 9600 9700 9800 9900 9A00 9B00 9C00 9D00 9E00 9F00

40960 A000 49152 41216 A100 49408 41472 A200 49664 41728 A300 49920 41984 A400 50176 42240 A500 50432 42496 A600 50688 42752 A700 50944 43008 A800 51200 43264 A900 51456 43520 AA00 51712 43776 AB00 51968 44032 AC00 52224 44288 AD00 52480 44544 AE00 52736 44800 AF00 52992 45056 B000 53248 45312 B100 53504 45568 B200 53760 45824 B300 54016 46080 B400 54272 46336 B500 54528 46592 B600 54784 46848 B700 55040 47104 B800 55296 47360 B900 55552 47616 BA00 55808 47872 BB00 56064 48128 BC00 56320 48384 BD00 56576 48640 BE00 56832 48896 BF00 57088

C000 C100 C200 C300 C400 C500 C600 C700 C800 C900 CA00 CB00 CC00 CD00 CE00 CF00 D000 D100 D200 D300 D400 D500 D600 D700 D800 D900 DA00 DB00 DC00 DD00 DE00 DF00

57344 57600 57856 58112 58368 58624 58880 59136 59392 59648 59904 60160 60416 60672 60928 61184 61440 61696 61952 62208 62464 62720 62976 63232 63488 63744 64000 64256 64512 64768 65024 65280

E000 E100 E200 E300 E400 E500 E600 E700 E800 E900 EA00 EB00 EC00 ED00 EE00 EF00 F000 F100 F200 F300 F400 F500 F600 F700 F800 F900 FA00 FB00 FC00 FD00 FE00 FF00

3. Battery End Check (VC-240/241 board) Check the battery end voltage. Mode Camera recording and VTR playback Subject

Arbitrary

Note: It is normal though the following symptoms appear during the battery end check. 1) The message of “FOR InfoLITHIUM BATTERY ONLY” on the LCD or viewfinder screen. 2) The tally lamp is flashing.

Connection: 1) Connect the regulated power supply and the digital voltmeter to the battery terminal as shown in Fig. 5-3-4. Checking method: 1) Adjust the output voltage of the regulated power supply so that the digital voltmeter display is 6.0 ± 0.1Vdc. 2) Turn off the power supply. 3) Turn on the HOLD switch of the adjustment remote commander. 4) Turn on the power supply. 5) Load a cassette, and set to the camera recording mode. 6) Decrease the output voltage of the regulated power supply so that the digital voltmeter display is 5.5 ± 0.1Vdc. 7) Record the camera signal for a minute. 8) Playback the recorded section and check that the playback picture and sound are normal.

Regulated power supply +

5.5 ± 0.01 Vdc

+ +

Digital volt meter

Fig. 5-3-4.

5-50

Ver 1.1 2000. 06

3-3.

2. PLL f0 & LPF f0 Adjustment (VC-240/241 board)

SERVO AND RF SYSTEM ADJUSTMENT

Before perform the servo and RF system adjustments, check that the specified value of “36MHz/54MHz/66MHz Origin Oscillation Adjustment” of “CAMERA SYSTEM ADJUSTMENT” is satisfied. Note: Only for the DCR-TRV20/TRV20E model, the lens block (CD-252 board) must be connected when performing the adjustment.

Adjusting Procedure: 1. Cap FG duty adjustment 2. PLL f0 & LPF f0 adjustment 3. Switching position adjustment 4. AGC center level and APC & AEQ adjustment 5. PLL f0 & LPF f0 final adjustment

Adjustment remote commander C

Adjustment Address Specified Value

16 00

Display data of page: 3, address: 03 Adjustment remote commander

Adjustment Page Adjustment Address

C 1F, 20, 22, 29

Specified Value

Bit2, bit3 and bit6 are “0”

Note: If bit2, bit3 or bit 6 of the data is “1”, there are errors. (For the error contents, see the following table. For the bit values, refer to “5-4. SERVICE MODE”, “4-3. 3. Bit value discrimination”.)

5)

Select page: 0, address: 01, and set data: 00.

Bit value of page: 3, address: 03 data bit 6 = 1 bit 3 = 1 bit 2 = 1

Adjusting method: 1) Close the cassette compartment without inserting a cassette. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: 3, address: 01, set data: 1B, and press the PAUSE button of the adjustment remote commander. 4) Select page: 3, address: 02, and check that the data changes starting from “1B” to “2B” to “00” in this order. 5) Select page: 3, address: 03, and check that the data is “00”. Note: If the data of page: 3, address: 03 is “01”, adjustment has errors or the mechanism deck is defective.

6)

VTR stop

Measurement Point Measuring Instrument

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 01, set data: 30, and press the PAUSE button of the adjustment remote commander. 3) Select page: 3, address: 02, and check that the data changes to “00”. 4) Select page: 3, address: 03, and check that bit2, bit3 and bit 6 of the data are “0”.

1. Cap FG Duty Adjustment (VC-240/241 board) Set the Cap FG signal duty cycle to 50% to establish an appropriate capstan servo. If deviated, the uneven rotation of capstan and noise can occur. Measurement Point Display data of page: 3, address: 03 Measuring Instrument Adjustment Page

Mode

Select page: 0, address: 01, and set data: 00.

5-51

Error contents LPF f0 is defective PLL f0, final adjustment is defective PLL f0, final adjustment time-out

4. AGC Center Level and APC & AEQ Adjustment

3. Switching Position Adjustment (VC-240/241 board) Mode

VTR playback

Signal Measurement Point

SW/OL reference tape (XH2-3) Display data of page: 3, address: 03

Measuring Instrument Adjustment Page

Adjustment remote commander C

Adjustment Address Specified Value

10, 11, 12, 13 00

4-1. Preparations before adjustments Mode Camera recording Subject

Adjusting method: 1) Select page: 2, address: 30, and set data: 40. 2) Record the camera signal for three minutes.

4-2. AGC Center Level Adjustment (VC-240/241 board) Mode Playback

Adjusting method: 1) Insert the SW/OL reference tape and enter the VTR STOP mode. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: 3, address: 21, and check that the data is “02”.

Signal Measurement Point

Note: If the data of page: 3, address: 21 is “72”, the tape top being played. After playing the tape for 1 to 2 seconds, stop it, perform step 4 and higher.

4) 5) 6)

Select page: 3, address: 01, set data: 0D, and press the PAUSE button of the adjustment remote commander. Select page: 3, address: 02, and check that the data changes to “00”. Select page: 3, address: 03, and check that the data is “00”. Note: If bit 0 of page: 3, address: 03 data is “1”, the even channel is defective. If bit 1 is “1”, the odd channel is defective. Contents of the defect is written into page: C, addresses: 10 and 12. See the following table. (For the bit values, refer to “5-4. SERVICE MODE”, “4-3. 3. Bit value discrimination”. )

7)

Arbitrary

Recorded signal at “Preparations before adjustments” Pin w; of CN009 (RF MON) (Note 1) Ext. trigger : Pin qj of CN009 (SWP)

Measuring Instrument Adjustment Page

Oscilloscope C

Adjustment Address Specified Value

1E The display data of page: 3, address: 03 is “00”

Note 1: Connect a 75Ω resistor between Pin w; and Pin ql (GND) of CN009. 75Ω resistor (Parts code: 1-247-804-11)

Select page: 0, address: 01, and set data: 00.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Playback the recorded signal at “Preparations before adjustments” 3) Select page: 3, address: 33, and set data: 08. 4) Confirm that the playback RF signal is stable. 5) Select page: 3, address: 01, set data: 23, and press the PAUSE button of the adjustment remote commander. 6) Select page: 3, address: 02, and check that the data is “00”. 7) Select page: 3, address: 03, and check that the data is “00”.

When the even channel is defective Data of page: C, Contents of defect address: 10 EE Writing into EEPROM (IC502) is defective E8 Adjustment data is out of range E7 No data is returned from IC301 (CAIN) When the odd channel is defective Data of page: C, Contents of defect address: 12 EE Writing into EEPROM (IC502) is defective E8 Adjustment data is out of range E7 No data is returned from IC301 (CAIN)

Note: If the data of page: 3, address: 03 is other than “00”, adjustment has errors. (Take an appropriate remedial measures according to the errors referring to the following table. )

8)

Perform “APC & AEQ Adjustment”.

Data of page: 3, address: 03 20 30 40 50

Contents of defect Perform re-adjustment. (Note 2) The machine is defective Perform re-adjustment (Note 2) The machine is defective

Note 2: If this data is displayed twice successively, the machine is defective.

PB RF signal is stable

Pin w;

Pin qj 6.7 msec

Fig. 5-3-5.

5-52

Ver 1.1 2000. 06

4-3. APC & AEQ Adjustment (VC-240/241 board)

5. PLL f0 & LPF f0 Final Adjustment (VC-240/241 board)

Mode

Playback

Mode

VTR stop

Signal

Recorded signal at “Preparations before adjustments” Pin w; of CN009 (RF MON) (Note 1) Ext. trigger : Pin qj of CN009 (SWP)

Signal Measurement Point

Arbitrary Display data of page: 3, address: 03

Measuring Instrument Adjustment Page

Adjustment remote commander C

Adjustment Address Specified Value

1F, 20, 22, 29 Bit2, bit3 and bit6 are “0”

Measurement Point Measuring Instrument Adjustment Page

Oscilloscope C

Adjustment Address Specified Value

18, 19, 1B, 1C, 21, 2C The display data of page: 3, address: 03 is “00”

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 01, set data: 30, and press the PAUSE button of the adjustment remote commander. 3) Select page: 3, address: 02, and check that the data changes to “00”. 4) Select page: 3, address: 03, and check that bit2, bit3 and bit 6 of the data are “0”.

Note 1: Connect a 75Ω resistor between Pin w; and Pin ql (GND) of CN009. 75Ω resistor (Parts code: 1-247-804-11) Note 2: The “AGC Center Level Adjustment” must have already been completed before starting this adjustment.

Note: If bit2, bit3 or bit 6 of the data is “1”, there are errors. (For the error contents, see the following table. For the bit values, refer to “5-4. SERVICE MODE”, “4-3. 3. Bit value discrimination”.)

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Playback the recorded signal at “Preparations before adjustments” 3) Select page: 3, address: 33, and set data: 08. 4) Check that the playback RF signal is stable. 5) Select page: 3, address: 01, set data: 07, and press the PAUSE button of the adjustment remote commander. 6) Select page: 3, address: 02, and check that the data changes from “07” to “00” in about 15 seconds after pressing the PAUSE button. 7) Select page: 3, address: 03, and check that the data is “00”.

5)

Note: If the data of page: 3, address: 03 is other than “00”, adjustment has errors. (Take an appropriate remedial measures according to the errors referring to the following table. )

8)

Perform “Processing after Completing Adjustments”.

Data of page: 3, address: 03 20 30 50 60 80

Select page: 0, address: 01, and set data: 00.

Bit value of page: 3, address: 03 bit 6 = 1 bit 3 = 1 bit 2 = 1

Contents of defect Perform re-adjustment. (Note 3) The machine is defective Perform re-adjustment (Note 3) The machine is defective The machine is defective

Note 3: If this data is displayed twice successively, the machine is defective.

4-4. Processing after Completing Adjustments 1) Select page: 2, address: 30, and set data: 00. 2) Select page: 3, address: 33, and set data: 00. 3) Select page: 0, address: 01, and set data: 00. PB RF signal is stable

Pin w;

Pin qj 6.7 msec

Fig. 5-3-6.

5-53

Error contents LPF f0 is defective PLL f0 final adjustment is defective PLL f0 final adjustment time-out

3-4.

2. S VIDEO OUT Y Level Adjustment (VC-240/241 Board)

VIDEO SYSTEM ADJUSTMENTS

Before perform the video system adjustments, check that the specified value of “36MHz/54MHz/66MHz Origin Oscillation Adjustment” of “CAMERA SYSTEM ADJUSTMENT” is satisfied. Note: Only for the DCR-TRV20/TRV20E model, the lens block (CD-252 board) must be connected when performing the adjustments.

3-4-1.

Base Band Block Adjustments

1. Chroma BPF f0 Adjustment (VC-240/241 Board) Set the center frequency of IC1301 chroma band-pass filter. Mode Camera Subject Measurement Point

All black (Cover the lens with the lens cap) CH1: Chroma signal terminal of S VIDEO jack (75Ω terminated) CH2: Y signal terminal of S VIDEO jack (75Ω terminated)

Measuring Instrument Adjustment Page

Oscilloscope C

Adjustment Address Specified Value

28 A = 100mVp-p or less B = 200mVp-p or more

Camera

Subject Measurement Point

Arbitrary Y signal terminal of S VIDEO jack (75Ω terminated)

Measuring Instrument Adjustment Page

Oscilloscope C

Adjustment Address Specified Value

25 A = 1000 ± 14mV

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 35. After noting down the data of this address, set data: 01 to the address. 3) Select page: 3, address: 0C, set data: 02, and press the PAUSE button of the adjustment remote commander. 4) Select page: C, address: 25, change the data and set the Y signal level (A) to the specified value. 5) Press the PAUSE button. 6) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 7) Select page: 2, address: 35, and set the data that is noted down at step 2). 8) Select page: 0, address: 01, and set data: 00.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Check that the burst signal (B) is output to the chroma signal terminal of S VIDEO jack. 3) Select page: 3, address: 0C, set data: 04, and press the PAUSE button. 4) Select page: C, address: 28, and change the data for minimum amplitude of the burst signal level (A). (The data of address: 28 should be “00” to “07”.) 5) Press the PAUSE button. 6) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 7) Check that the burst signal level (B) satisfies the specified value. 8) Select page: 0, address: 01, and set data: 00.

Center of luminance line

A

H

Fig. 5-3-8.

When the data of page: 3, address: 0C, is 04: A CH1

CH2

H

When the data of page: 3, address: 0C, is 00:

CH1

Mode

B

H

Fig. 5-3-7.

5-54

3. S VIDEO OUT Chroma Level Adjustment (VC-240/241 Board) Mode Camera Subject Measurement Point

4. AV OUT Y, Chroma Level Check (VC-240/241 Board)

Arbitrary Chroma signal terminal of S VIDEO jack (75Ω terminated) External trigger: Y signal terminal of S VIDEO jack

Measuring Instrument Adjustment Page

Oscilloscope C

Adjustment Address Specified Value

26, 27 Cr level:

A = 714 ± 14mV(NTSC) A = 700 ± 14mV(PAL) Cb level: B = 714 ± 14mV(NTSC) B = 700 ± 14mV(PAL) Burst level: C = 286 ± 6mV(NTSC) C = 300 ± 6mV(PAL)

Arbitrary Video terminal of AUDIO/VIDEO jack (75Ω terminated)

Measuring Instrument Specified Value

Oscilloscope Sync level: A = 286 ± 18mV(NTSC) A = 300 ± 18mV(PAL) Burst level: B = 286 ± 18(mV(NTSC) B = 300 ± 18mV(PAL)

B A H

Fig. 5-3-10.

H

C

0.28 µsec (NTSC) 0.23 µsec (PAL)

Camera

Subject Measurement Point

Adjusting method: 1) Select page: 2, address: 35. After noting down the data of this address, set data: 01 to the address. 2) Select page: 3, address: 0C, set data: 02, and press the PAUSE button of the adjustment remote commander. 3) Check that the sync signal level (A) satisfies the specified value. 4) Check that the burst signal level (B) satisfies the specified value. 5) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 6) Select page: 2, address: 35, and set the data that is noted down at step 1).

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 35. After noting down the data of this address, set data: 01 to the address. 3) Select page: 3, address: 0C, set data: 02, and press the PAUSE button of the adjustment remote commander. 4) Select page: C, address: 26, change the data and set the Cr signal level (A) to the specified value. 5) Press the PAUSE button. 6) Select page: C, address: 27, change the data and set the Cb signal level (B) to the specified value. 7) Press the PAUSE button. 8) Check that the burst signal level (C) is satisfied the specified value. 9) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 10) Select page: 2, address: 35, and set the data that is noted down at step 2). 11) Select page: 0, address: 01, and set data: 00.

A

Mode

B

0.28 µsec (NTSC) 0.23 µsec (PAL)

Fig. 5-3-9.

5-55

3-4-2.

BIST Check

1-4. IC301 VFD PB BIST Check • EX Y BIST Check 1) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 2) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 3) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 4) When the IC301 EX Y playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 FB 15 F4

1. Playback System Check 1-1. Preparations for Playback 1) Set the POWER switch to VCR (or PLAYER) position. 2) Connect the adjustment remote commander and set the HOLD switch to ON (SERVICE) position. 3) Select page: 0, address: 01, and set data: 01. 4) Select page: C, address: 42, set data: 00, and press the PAUSE button. 5) Playback the BIST check tape. (XH5-6 (NTSC), XH5-6P (PAL)) Note1:Perform the following checks in the playback mode. Note2: Use the AC power adaptor (AC-L10 etc.) or the info LITHIUM battery (NP-FM50 etc.).

1-2. IC301 TRX (RF) PB BIST Check 1) Select page: 3, address: 70, set data: 04, and press the PAUSE button. 2) Select page: 3, address: 70, set data: 00, and press the PAUSE button. 3) When the IC301 TRX (RF) playback system is normal, the display data (combination data) of page: 3, address: 73 and 74 agrees with any combination as shown below. NTSC model Address Data 73 63 C5 75 D3 59 FF 74 84 55 07 D6 01 D0 PAL model Address 73 86 74 35

Data AA 33

PAL model Address Data 14 54 15 ED • EVF Y BIST Check 5) Select page: 3, address: 10, set data: 88, and press the PAUSE button. 6) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 7) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 8) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 9) When the IC301 EVF Y playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 9B 15 C3

90 B6

1-3. IC301 AUD (ABUS) PB BIST Check 1) Select page: 3, address: 11, set data: 04, and press the PAUSE button. 2) Select page: 3, address: 12, set data: 08, and press the PAUSE button. 3) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 4) Select page: 3, address: 13, set data: 03, and press the PAUSE button. 5) When the IC301 AUD (ABUS) playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 41 15 81

PAL model Address Data 14 20 15 F8 • EVF Cr BIST Check 10) Select page: 3, address: 10, set data: 89, and press the PAUSE button. 11) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 12) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 13) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 14) When the IC301 EVF Cr playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 2E 15 34

PAL model Address Data 14 2D 15 7C

PAL model Address Data 14 33 15 DD

5-56

• EVF Cb BIST Check 15) Select page: 3, address: 10, set data: 8A, and press the PAUSE button. 16) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 17) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 18) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 19) When the IC301 EVF Cb playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 A9 15 39

• PANEL Cb BIST Check 30) Select page: 3, address: 10, set data: 9A, and press the PAUSE button. 31) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 32) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 33) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 34) When the IC301 PANEL Cb playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 A9 15 39

PAL model Address Data 14 AA 15 03

PAL model Address Data 14 AA 15 03

• PANEL Y BIST Check 20) Select page: 3, address: 10, set data: 98, and press the PAUSE button. 21) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 22) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 23) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 24) When the IC301 PANEL Y playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 9B 15 C3

1-5. IC301 ENCODER BIST Check 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 8, address: 21, set data: 0F, and press the PAUSE button. • ENCODER Ya BIST Check 3) Select page: 3, address: 10, set data: 8B, and press the PAUSE button. 4) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 5) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 6) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 7) When the IC301 ENCODER Ya playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 FD 15 3E

PAL model Address Data 14 20 15 F8

PAL model Address Data 14 58 15 BE

• PANEL Cr BIST Check 25) Select page: 3, address: 10, set data: 99, and press the PAUSE button. 26) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 27) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 28) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 29) When the IC301 PANEL Cr playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 2E 15 34 PAL model Address Data 14 33 15 DD

5-57

• ENCODER Yb BIST Check 8) Select page: 3, address: 10, set data: 8C, and press the PAUSE button. 9) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 10) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 11) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 12) When the IC301 ENCODER Yb playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 94 15 D6

1-6. Processing after Completing Playback System Check 1) 2)

3) 4) 5)

PAL model Address Data 14 A1 15 ED • ENCODER Ca BIST Check 13) Select page: 3, address: 10, set data: 8D, and press the PAUSE button. 14) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 15) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 16) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 17) When the IC301 ENCODER Ca playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 11 4E FD 3B 15 PAL model Data Address 14 E8 7B 62 B0 15 • ENCODER Cb BIST Check 18) Select page: 3, address: 10, set data: 8E, and press the PAUSE button. 19) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 20) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 21) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 22) When the IC301 ENCODER Cb playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 5C BC 20 A8 15 PAL model Data Address 14 96 35 79 7C 15

5-58

Select page: 0, address: 01, and set data: 01. Select page: C, address: 42, set the following data and press the PAUSE button. 00: DCR-TRV6/TRV6E 28: DCR-TRV11/TRV11E 48: DCR-TRV20/TRV20E Select page: 8, address: 21, set data: 03, and press the PAUSE button. Select page: 0, address: 01, and set data: 00. Turn off the power and turn on again.

2. Recording System Check 2-1. Preparations for recording 1) Playback the BIST check tape.(XH5-6(NTSC), XH5-6P(PAL)) 2) Select page: 3, address: 10, set data: C0, and press the PAUSE button. 3) Select page: 3, address: 11, set data: 07, and press the PAUSE button. 4) Enter the stop mode. 5) While keep the HOLD switch of the adjustment remote commander at ON(SERVICE) position, eject the BIST check tape and close the cassette compartment without inserting a cassette. 6) Set the power switch to “CAMERA”. 7) Select page: 3, address: 01, set data: 0C, and press the PAUSE button. 2-2. IC301 TRX (RF) BIST Check 1) Select page: 3, address: 70, set data: 04, and press the PAUSE button. 2) Select page: 3, address: 70, set data: 00, and press the PAUSE button. 3) When the IC301 TRX (RF) recording system from is normal, the display data (combination data) of page: 3, address: 71 and 72 agrees with any combination as shown below. NTSC model Address Data 26 5E 71 72 95 E3 PAL model Data Address 71 53 77 DF D5 72 2-3. Processing after Completing Recording System Check 1) 2)

Select page: 3, address: 01, set data: 00, and press the PAUSE button. Turn off the power and turn on again.

5-59

3-5.

2. IR Video Deviation Adjustment (VC-240/241 board) Mode VTR stop

IR TRANSMITTER ADJUSTMENTS

Adjust using a IR receiver jig (J-6082-383-A). Switch setting: SUPER LASER LINK ........................... ON (Red LED is lit) 1. IR Video Carrier Frequency Adjustment (VC-240/241 board) Mode VTR stop Signal Measurement Point

Arbitrary Pin 5 of CN003 of IR receiver jig (RF) (Or Pin qh of IC1901 of VC-240/241 board)

Measuring Instrument Adjustment Page

Frequency counter F

Adjustment Address Specified Value

Measuring Instrument Adjustment Page

Oscilloscope F

Adjustment Address Specified Value

6D A = 1.00 ± 0.05 V

Oscilloscope Main unit

6E f = 11.85 ± 0.05 MHz

IR receiver jig CN003 pin 5

Arbitrary VIDEO OUT terminal of IR receiver jig (Terminated at 75 Ω)

Connection of Equipment: Connect the measuring device as shown in the following figure, and adjust.

IR receiver jig

75 Ω

VIDEO OUT 75 Ω (1-247-804-11)

Connection of Equipment Connect the measuring device as shown in the following figure, and adjust. Main unit

Signal Measurement Point

Fig. 5-3-12.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 0C, set data: 02, and press the PAUSE button of the adjustment remote commander. 3) Select page: F, address: 6D, and change the data, set the video signal amplitude (A) to the specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: 3, address: 0C, set data: 00, and press the PAUSE button of the adjustment remote commander. 6) Select page: 0, address: 01, and set data: 00.

Frequency counter

Fig. 5-3-11.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 0C, set data: 08, and press the PAUSE button of the adjustment remote commander. 3) Select page: F, address: 6E, change the data, and set the video carrier frequency (f) to the specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: 3, address: 0C, set data: 00, and press the PAUSE button of the adjustment remote commander. 6) Select page: 0, address: 01, and set data: 00.

A

H

Fig. 5-3-13.

5-60

3. IR Audio Deviation Adjustment (VC-240/241 board) Mode VTR stop Signal

Measurement Point

Video : No signal Audio : 400Hz, –7.5dBs, Audio left and right terminal of AUDIO/VIDEO jack AUDIO L terminal and AUDIO R terminal of IR receiver jig (Terminated at 47kΩ)

Measuring Instrument Adjustment Page

Audio level meter F

Adjustment Address Specified Value

6C Signal level: –7.5 ± 1.0 dBs Level difference of L and R: Below 2dB

Connection of Equipment: Connect the measuring device as shown in the following figure, and adjust. Main unit IR receiver jig

Video (Yellow)

AUDIO/ VIDEO AUDIO OUT L R

Audio oscillator Audio Left (White)

Attenuator

Audio level meter 600 Ω

Audio Right (Red)

600 Ω: 270 Ω (1-249-410-11) + 330 Ω (1-249-411-11) 47k Ω 47k Ω (1-249-437-11)

Fig. 5-3-14. Preparation: (Only for the AEP/UK model of DCR-TRV6E/TRV11E) 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 2C, after noting down the data of this address, set data: 32, and press the PAUSE button. 3) Turn off the HOLD switch of the adjustment remote commander. 4) Turn off the power. 5) Turn on the HOLD switch. 6) Turn on the power.

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Connect the audio level meter to the AUDIO L terminal of the IR receiver jig. 3) Select page: F, address: 6C, change the data and set the 400Hz audio signal level to the specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Connect the audio level meter to the AUDIO R terminal of the IR receiver jig. 6) Check that the 400Hz audio signal level is within the specified value. If outside, repeat from step 2). 7) Only for AEP/UK model of DCR-TRV6E/TRV11E, select page: D. address: 2C, set the data noted down at step 2) of “Preparation”, and press the PAUSE button. 8) Select page: 0, address: 01, and set data: 00.

5-61

3-6.

AUDIO SYSTEM ADJUSTMENTS

[Connection of Audio System Measuring Devices] Connect the audio system measuring devices as shown in Fig. 5-3-15. Main unit

Recording (Camera mode)

Audio oscillator

600 Ω

MIC

Left

Right

Attenuator

600 Ω: 270 Ω (1-249-410-11) + 330 Ω (1-249-411-11)

Playback Main unit

TV monitor Video (Yellow) Left (White)

AUDIO/ VIDEO OUT

47k Ω

Audio level meter or Distortion meter

Right (Red)

47k Ω 47k Ω (1-249-437-11)

Fig. 5-3-15.

5-62

1. Playback Level Check Mode VTR playback Signal

Measurement Point Measuring Instrument Specified Value

4. Overall Noise Level Check Mode Camera recording and playback

Alignment tape: For audio operation check (XH5-3 (NTSC)) (XH5-3P (PAL)) Audio left or right terminal of AUDIO VIDEO jack

Signal Measurement Point Measuring Instrument Specified Value

Audio level meter and frequency counter 32 kHz mode: 1 kHz, +3.0 ± 2.0dBs 48 kHz mode: 1 kHz, +3.0 ± 2.0dBs 44.1 kHz mode: The 7.35kHz signal level during EMP OFF is +2.0 ± 2.0dBs. The 7.35kHz signal level during EMP ON is –6 ± 2 dB from the signal level during EMP OFF.

5. Overall Separation Check Mode Signal

Camera recording and playback 400Hz, –66dBs signal: MIC jack [left] (Connect the MIC jack [right] to GND)

Measurement Point Measuring Instrument

Audio [right] terminal of AUDIO VIDEO jack Audio level meter

Specified Value

Below –40dBs (IHF-A filter ON)

2. Overall Level Characteristics Check Camera recording and playback 400Hz, –66 dBs signal: MIC jack left and right

Measurement Point Measuring Instrument

Audio left or right terminal of AUDIO VIDEO jack Audio level meter

Specified Value

–7.5 ± 3.0dBs

< > : Left channel check [ ] : Right channel check Checking Method: 1) Input the 400Hz, –66dBs signal in the [left] terminal of the MIC jack only. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the signal level of the audio [right] terminal is the specified value.

Checking Method: 1) Input the 400Hz, –66dBs signal in the MIC jack. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the 400Hz signal level is the specified value. 3. Overall Distortion Check Mode Signal

Camera recording and playback 400Hz, –66dBs signal: MIC jack left and right

Measurement Point

Audio left or right terminal of AUDIO VIDEO jack Audio distortion meter

Measuring Instrument Specified Value

Audio level meter Below –45dBs (IHF-A filter ON, 20kHz LPF ON)

Checking Method: 1) Insert a shorting plug in the MIC jack. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the noise level is the specified value.

Checking Method: 1) Check that the playback signal level is the specified value.

Mode Signal

No signal: Insert a shorting plug in the MIC jack Audio left or right terminal of AUDIO VIDEO jack

Below 0.4% (200Hz to 6kHz BPF ON)

Checking Method: 1) Input the 400Hz, –66dBs signal in the MIC jack. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the distortion is the specified value.

5-63

5-4. SERVICE MODE 4-1.

ADJUSTMENT REMOTE COMMANDER

2. Precautions upon using the adjustment remote commander Mishandling of the adjustment remote commander may erase the correct adjustment data at times. To prevent this, it is recommended that all adjustment data be noted down before beginning adjustments and new adjustment data after each adjustment.

The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The adjustment remote commander performs bi-directional communication with the unit using the remote commander signal line (LANC). The resultant data of this bi-directional communication is written in the non-volatile memory. 1. Using the adjustment remote commander 1) Connect the adjustment remote commander to the LANC terminal. 2) Set the HOLD switch of the adjustment remote commander to “HOLD” (SERVICE position). If it has been properly connected, the LCD on the adjustment remote commander will display as shown in Fig. 5-4-1.

Page

Data

Address

Fig. 5-4-1 3)

Operate the adjustment remote commander as follows. • Changing the page The page increases when the EDIT SEARCH+ button is pressed, and decreases when the EDIT SEARCH– button is pressed. There are altogether 16 pages, from 0 to F.

Hexadecimal 0 1 2 3 4 5 6 7 8 9 A B CD E F notation LCD Display 0 1 2 3 4 5 6 7 8 9 A b c d E F Decimal notation conversion value 0 1 2 3 4 5 6 7 8 9 10 1112 1314 15

4)

• Changing the address The address increases when the FF (M) button is pressed, and decreases when the REW (m) button is pressed. There are altogether 256 addresses, from 00 to FF. • Changing the data (Data setting) The data increases when the PLAY (N) button is pressed, and decreases when the STOP (x) button is pressed. There are altogether 256 data, from 00 to FF. • Writing the adjustment data The PAUSE button must be pressed to write the adjustment data (B, C, D, F, 7, 8 page) in the nonvolatile memory. (The new adjusting data will not be recorded in the nonvolatile memory if this step is not performed.) After completing all adjustments, turn off the main power supply once.

5-64

4-2.

DATA PROCESS

The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Indicates the hexadecimal-decimal conversion table. Hexadecimal-decimal Conversion Table Lower digit of hexadecimal

0

1

2

3

2 4

5

6

7

8

9

Upper digit of hexadecimal

1

A (A)

B (b)

C (c)

D (d)

E (E)

F (F)

0

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

1

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

2

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

3

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

4

64

65

66

67

68

69

70

71

72

73

74

77

76

77

78

79

5

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

6

96

97

98

99

100

101

102

103

104

105

106

107

108

109

110

111

7

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

8

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

9

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

A ( A)

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

B (b)

176

179

180

181

182

183

184

185

186

187

188

189

190

191

C ( c)

177 193

178

192

194

195

196

197

198

199

200

201

202

203

204

205

206

207

D (d)

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

E (E)

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

F (F)

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

255

Note: The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander. (Example) If the DDS display or the adjustment remote commander shows BD (bd); Because the upper digit of the adjustment number is B (b), and the lower digit is D (d), the meeting point “189” of 1 and 2 in the above table is the corresponding decimal number.

Table. 5-4-1.

5-65

4-3.

SERVICE MODE 2-1. EMG Code (Emergency Code) Codes corresponding to the errors which occur are written in addresses F4, F8 and FC. The type of error indicated by the code are shown in the following table.

1. Setting the Test Mode Page D Address 10 Data Function 00 Normal 01 Forced camera power ON 02 Forced VTR power ON 03 Forced camera + VTR power ON 05 Forced memory power ON • Before setting the data , select page: 0, address: 01, and set data: 01. • For page D, the data set is recorded in the non-volatile memory by pressing the PAUSE button of the adjustment remote commander. In this case, take note that the test mode will not be exited even when the main power is turned off. • After completing adjustments/repairs, be sure to return the data of this address to 00, and press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00.

Code 00 10 11 22 23 24 30 40 42

2. Emergence Memory Address Page C Address F4 to FF Address Contents F4 EMG code when first error occurs Upper: MSW code when shift starts when first F6 error occurs Lower: MSW code when first error occurs Lower: MSW code to be moved when first error F7 occurs F8 EMG code when second error occurs Upper: MSW code when shift starts when second FA error occurs Lower: MSW code when second error occurs Lower: MSW code to be moved when second error FB occurs FC EMG code when last error occurs Upper: MSW code when shift starts when last error FE occurs Lower: MSW code when last error occurs Lower: MSW code to be moved when last error FF occurs When no error occurs in this unit, data “00” is written in the above addresses (F4 to FF). when first error occurs in the unit, the data corresponding to the error is written in the first emergency address (F4 to F7). In the same way, when the second error occurs, the data corresponding to the error is written in the second emergency address (F8 to FB). Finally, when the last error occurs, the data corresponding to the error is written in the last emergency address (FC to FF). Note: After completing adjustments, be sure to initialize the data of addresses F4 to FF to “00”.

Initializing method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 01, set data: 37, and press the PAUSE button. 3) Select page: 0, address: 01, and set data: 00.

5-66

Emergency Type No error Loading motor emergency during loading Loading motor emergency during unloading T reel emergency during normal rotation S reel emergency during normal rotation T reel emergency (Short circuit between S reel terminal and T reel terminal) FG emergency at the start up of the capstan FG emergency at the start up of the drum FG emergency during normal rotation of the drum

Ver 1.1 2000. 06

2-2. MSW Code MSW when errors occur: Information on MSW (mode SW) when errors occur MSW when movement starts: Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved) MSW of target of movement: Information on target MSW of movement when the mechanism position is moved

Mechanical Position ← UNLOAD BL

EJ

LOAD → ULE

BL

SR

BL

GL

BL

STOP

BL

R/P

1 1 0 = 6

1 1 1 = 7 0 1 0 = 2

1 1 1 = 7 0 1 1 = 3

1 1 1 = 7 0 0 1 = 1

1 1 1 = 7 1 0 1 = 5

1 1 1 = 7

1 0 0 = 4

← C (MSB) ←B ← A (LSB)

LS chassis movement section

Lock released Cassette compartment

Pinch roller pressing

Position

Code

EJ

4

BL

7

ULE

5

SR GL

1 3

STOP

2

R/P

6

NULL

0

Contents Position at which the cassette component lock is released, at the farthest unload side mechanically at which the mechanism can move no further in the UNLOAD direction. BLANK code, at the boundary between codes. EJECT completion position. when the cassette is ejected, the mechanism will stop at this position. Cassette IN standby. The guide will start protruding out as the mechanism moves towards the LOAD position. Position at which it is possible to release the S ratchet. Guide loading are performed here. Stop position in the loading state. The pinch roller separates, the tension regulator returns, and the brake is imposed on both reels. PB, REC, CUE, REVIEW, PAUSE positions. When pinch roller is pressed, and the tension regulator is ON, the mechanism is operating at this position in modes in which normal images are shown. Code not existing in the MD. Default value.

5-67

3. Bit value discrimination Bit values must be discriminated using the display data of the adjustment remote commander for following items. Use the table below to discriminate if the bit value is “1” or “0”. Display on the adjustment remote commander

Address Page

bit3 to bit0 discrimination bit7 to bit4 discrimination

Display on the adjustment remote commander 0 1 2 3 4 5 6 7 8 9 A (A) B (b) C (c) D (d) E (E) B F (F)

bit3 or bit7 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Bit values bit2 bit1 or or bit6 bit5 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1

bit0 or bit4 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

Example: If “8E” is displayed on the adjustment remote commander, the bit values for bit7 to bit4 are shown in the A column, and the bit values for bit3 to bit0 are shown in the B column.

4. Switch check (1) Page 2 Bit 0 1 2 3 4 5 6 7

Address 43 Function VTR MODE SW (PS-30150 block S1) CAM STBY SW (PS-30150 block S1) START/STOP SW (PS-30150 block S2) EJECT SW (FK-30150 block S61) CC DOWN SW (Mechanism chassis) PHOTO FREEZE SW (FK-30150 block S71) PHOTO STBY SW (PS-30150 block S1)

When bit value=1 OFF OFF OFF OFF OFF (UP) OFF OFF

When bit value=0 ON ON ON ON ON (DOWN) ON ON

Using method: 1) Select page: 2, address: 43. 2) By discriminating the bit value of display data, the state of the switch can be discriminated.

5-68

5. Switch check (2) Page 2

Address 60 to 67

Using method: 1) Select page:2, address: 60 to 67. 2) By discriminating the display data, the pressed key can be discriminated. Address 60 (KEY AD0) (IC1104 od) 61 (KEY AD1) (IC1104 of) 62 (KEY AD2) (IC1104 og) 63 (KEY AD3) (IC1104 oh) 64 (KEY AD4) (IC1104 oj) 65 (KEY AD5) (IC1104 ok) 66 (KEY AD6) (IC1104 ol) 67 (KEY AD7) (IC1104 FB101 FB102 FB103 FB104 FB105

1-414-445-11 1-414-445-11 1-414-445-11 1-414-445-11 1-414-445-11

FERRITE FERRITE FERRITE FERRITE FERRITE

0UH 0UH 0UH 0UH 0UH

FB106 FB108 FB109

1-414-445-11 FERRITE 1-414-445-11 FERRITE 1-414-656-11 FERRITE

0UH 0UH 0UH

< CAPACITOR > C101 C102 C103 C104 C105

1-164-004-11 1-125-777-11 1-107-687-11 1-104-851-11 1-125-777-11

CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP

0.1uF 0.1uF 3.3uF 10uF 0.1uF

10% 10% 20% 20% 10%

25V 10V 20V 10V 10V

C106 C107 C108 C109 C110

1-113-987-11 1-104-851-11 1-107-826-91 1-125-777-11 1-164-937-11

TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

4.7uF 10uF 0.1uF 0.1uF 0.001uF

20% 20% 10% 10% 10%

25V 10V 16V 10V 16V

C111 C112 C113 C114 C116

1-164-845-11 1-164-937-11 1-107-819-11 1-107-820-11 1-107-687-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP

5PF 0.001uF 0.022uF 0.1uF 3.3uF

0.25PF 16V 10% 16V 10% 16V 16V 20% 20V

C118 C119 C120 C122 C124

1-125-777-11 1-125-777-11 1-125-777-11 1-125-777-11 1-117-919-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP

0.1uF 0.1uF 0.1uF 0.1uF 10uF

10% 10% 10% 10% 20%

10V 10V 10V 10V 6.3V

C125 C126 C127 C128 C129

1-125-777-11 1-117-919-11 1-125-777-11 1-125-777-11 1-117-919-11

CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP

0.1uF 10uF 0.1uF 0.1uF 10uF

10% 20% 10% 10% 20%

10V 6.3V 10V 10V 6.3V

C130 C131 C132 C151 C152

1-125-777-11 1-164-870-11 1-162-966-11 1-117-919-11 1-125-837-91

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP

0.1uF 68PF 0.0022uF 10uF 1uF

10% 5% 10% 20% 10%

10V 16V 50V 6.3V 6.3V

< IC > IC101 IC102 IC103 IC104

CCD BLOCK ASSY IC CXD2477R-T4 IC TA75S01F(TE85R) IC AD80017JRURL < COIL >

L101 L103 L104 L105 L151

1-469-528-91 1-414-771-91 1-414-771-91 1-414-771-91 1-414-771-91

INDUCTOR INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP

100uH 10uH 10uH 10uH 10uH

< TRANSISTOR > Q101 Q102 Q103 Q104

8-729-037-74 8-729-050-22 8-729-041-23 8-729-037-74

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

UN9213J-(TX).SO 2SC4250(T5LSONY1) NDS356AP UN9213J-(K8).SO

< RESISTOR >

< CONNECTOR > CN101 CN151 CN152

A-7031-073-A 8-752-400-37 8-759-075-66 8-759-638-68

1-784-939-11 CONNECTOR, BOARD TO BOARD 60P 1-784-421-11 CONNECTOR, FFC/FPC (ZIF) 27P 1-766-335-21 CONNECTOR, FFC/FPC 5P

R102 R104 R105 R106 R107

1-216-808-11 1-218-990-11 1-218-961-11 1-218-962-11 1-218-985-11

METAL CHIP SHORT RES-CHIP RES-CHIP RES-CHIP

82 0 4.7K 5.6K 470K

5%

1/16W

5% 5% 5%

1/16W 1/16W 1/16W

R108 R109 R112 R113 R114

1-218-967-11 1-218-990-11 1-218-981-11 1-218-965-11 1-218-989-11

RES-CHIP SHORT RES-CHIP RES-CHIP RES-CHIP

15K 0 220K 10K 1M

5%

1/16W

5% 5% 5%

1/16W 1/16W 1/16W

R122 R123

1-218-990-11 SHORT 1-218-990-11 SHORT

0 0

< DIODE > D101

Be sure to read “Precautions upon replacing CCD imager” on page 4-12 when changing the CCD imager.

8-713-103-84 DIODE 1T379-01-T8A

6-11

CD-252 Ref. No.

CK-92

Part No.

CK-94

Description

Remarks

Ref. No.

< VIBRATOR > X101 1-781-632-21 VIBRATOR, CRYSTAL (66MHz)(TRV20) X101 1-781-633-21 VIBRATOR, CRYSTAL (54MHz)(TRV20E) ************************************************************ A-7074-313-A CK-92(H) BOARD, COMPLETE (TRV11/TRV11E/TRV20) ************************************ (Ref.No.;30000Series)

Part No.

Description

S3206 S3207 S3208 S3209 S3210

1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61

SWITCH, KEY BOARD (MEMORY +) SWITCH, KEY BOARD (DIGITAL EFFECT) SWITCH, KEY BOARD (SELF TIMER) SWITCH, KEY BOARD (MEMORY -) SWITCH, KEY BOARD (TITLE)

Remarks

S3211 S3212 S3213 S3214 S3215

1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61

SWITCH, KEY BOARD (END SEARCH) SWITCH, KEY BOARD (MEMORY MIX) SWITCH, KEY BOARD (PB ZOOM) SWITCH, KEY BOARD (DATA CODE) SWITCH, KEY BOARD (MEMORY DELETE)

< BATTERY > S3216 1-771-138-61 SWITCH, KEY BOARD (MENU) S3217 1-771-138-61 SWITCH, KEY BOARD (DISPLAY) S3218 1-771-138-61 SWITCH, KEY BOARD (RESET) ************************************************************

BT3201 1-528-724-21 BATTERY, V/L RECHARGEABLE < CAPACITOR > C3201 C3203

1-104-913-11 TANTAL. CHIP 1-104-919-11 TANTAL. CHIP

10uF 10uF

20% 20%

A-7074-396-A CK-94(H) BOARD, COMPLETE (TRV20E) ******************************** A-7074-393-A CK-94(L) BOARD, COMPLETE (TRV6/TRV6E) ************************************ (Ref.No.;30000Series)

16V 25V

< CONNECTOR > CN3201 CN3202 CN3203 CN3204 CN3205

1-779-064-11 1-785-283-21 1-573-347-11 1-766-336-21 1-784-424-21

PIN, CONNECTOR (PC BOARD) 12P PIN, CONNECTOR (PC BOARD) 14P CONNECTOR, FFC/FPC (ZIF) 7P CONNECTOR, FFC/FPC 6P CONNECTOR, FFC/FPC (ZIF) 51P

< BATTERY > BT3201 1-528-724-21 BATTERY, V/L RECHARGEABLE < CAPACITOR >

CN3206 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P C3201 C3203

< DIODE > D3201 D3202 D3203 D3204

8-719-062-16 8-719-062-16 8-719-062-16 8-719-062-16

DIODE DIODE DIODE DIODE

01ZA8.2(TPL3) 01ZA8.2(TPL3) 01ZA8.2(TPL3) 01ZA8.2(TPL3)

1-104-913-11 TANTAL. CHIP 1-104-919-11 TANTAL. CHIP

10uF 10uF

20% 20%

16V 25V (TRV20E)

< CONNECTOR > CN3201 CN3202 CN3203 CN3204 CN3205

< RESISTOR > R3201 R3202 R3203 R3204 R3205

1-216-295-91 1-218-969-11 1-218-969-11 1-218-969-11 1-218-963-11

SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP

0 22K 22K 22K 6.8K

5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W

R3206 R3207 R3208 R3209 R3210

1-218-963-11 1-218-963-11 1-218-959-11 1-218-959-11 1-218-959-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

6.8K 6.8K 3.3K 3.3K 3.3K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

R3211 R3212 R3213 R3214 R3215

1-218-955-11 1-218-955-11 1-218-955-11 1-218-954-11 1-218-954-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

1.5K 1.5K 1.5K 1.2K 1.2K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

R3216 R3217

1-218-954-11 RES-CHIP 1-218-953-11 RES-CHIP

1.2K 1K

5% 5%

1/16W 1/16W

1-779-064-11 1-785-283-21 1-573-347-11 1-766-336-21 1-784-424-21

PIN, CONNECTOR (PC BOARD) 12P PIN, CONNECTOR (PC BOARD) 14P CONNECTOR, FFC/FPC (ZIF) 7P CONNECTOR, FFC/FPC 6P CONNECTOR, FFC/FPC (ZIF) 51P

CN3206 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P < DIODE > D3201 D3202 D3203 D3204

8-719-062-16 8-719-062-16 8-719-062-16 8-719-062-16

DIODE DIODE DIODE DIODE

01ZA8.2(TPL3) 01ZA8.2(TPL3) 01ZA8.2(TPL3) 01ZA8.2(TPL3)

< RESISTOR >

< SWITCH > S3201 S3202 S3203 S3204 S3205

1-762-805-21 1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61

SWITCH, PUSH (1 KEY) (PANEL CLOSE) SWITCH, KEY BOARD (FADER) SWITCH, KEY BOARD (MEMORY INDEX) SWITCH, KEY BOARD (BACK LIGHT) SWITCH, KEY BOARD (MEMORY PLAY)

6-12

R3201 R3202 R3203 R3204 R3205

1-216-295-91 1-218-969-11 1-218-969-11 1-218-969-11 1-218-963-11

SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP

0 22K 22K 22K 6.8K

5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W

R3206 R3207 R3208 R3209 R3210

1-218-963-11 1-218-963-11 1-218-959-11 1-218-959-11 1-218-959-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

6.8K 6.8K 3.3K 3.3K 3.3K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

R3211 R3212 R3213 R3214 R3215

1-218-955-11 1-218-955-11 1-218-955-11 1-218-954-11 1-218-954-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

1.5K 1.5K 1.5K 1.2K 1.2K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

CK-94 Ref. No. R3216 R3217

Part No.

Description

1-218-954-11 RES-CHIP 1-218-953-11 RES-CHIP

Remarks 1.2K 1K

5% 5%

Ref. No.

1/16W 1/16W

< SWITCH > S3201 S3202 S3203 S3204 S3205

1-762-805-21 SWITCH, PUSH (1 KEY) (PANEL CLOSE) 1-771-138-61 SWITCH, KEY BOARD (FADER) 1-771-138-61 SWITCH, KEY BOARD (MEMORY INDEX) (TRV20E) 1-771-138-61 SWITCH, KEY BOARD (BACK LIGHT) 1-771-138-61 SWITCH, KEY BOARD (MEMORY PLAY) (TRV20E)

S3206 S3207 S3208 S3209 S3210

1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61

SWITCH, KEY BOARD (MEMORY +) (TRV20E) SWITCH, KEY BOARD (DIGITAL EFFECT) SWITCH, KEY BOARD (SELF TIMER) SWITCH, KEY BOARD (MEMORY -) (TRV20E) SWITCH, KEY BOARD (TITLE)

S3211 S3212 S3213 S3214 S3215

1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61

SWITCH, KEY BOARD (END SEARCH) SWITCH, KEY BOARD (MEMORY MIX)(TRV20E) SWITCH, KEY BOARD (PB ZOOM) SWITCH, KEY BOARD (DATA CODE) SWITCH, KEY BOARD (MEMORY DELETE) (TRV20E)

S3216 1-771-138-61 SWITCH, KEY BOARD (MENU) S3217 1-771-138-61 SWITCH, KEY BOARD (DISPLAY) S3218 1-771-138-61 SWITCH, KEY BOARD (RESET) ************************************************************ A-7074-307-A DD-137(H) BOARD, COMPLETE (TRV20/TRV20E) ************************* A-7074-392-A DD-137(L) BOARD, COMPLETE (TRV6/TRV6E) ************************* A-7074-365-A DD-137(M) BOARD, COMPLETE (TRV11/TRV11E) ************************* (Ref.No.;10000Series)

Part No.

Description

C1622 C1623 C1624 C1625 C1626

1-109-982-11 1-127-760-91 1-127-760-91 1-164-939-11 1-109-982-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

C1627 C1628 C1629 C1630 C1631

1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V (TRV11/TRV11E/TRV20/TRV20E) 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V

C1632 C1633 C1634 C1635

1-164-940-11 1-115-566-11 1-115-566-11 1-115-566-11

1-107-819-11 1-125-777-11 1-107-819-11 1-107-819-11 1-164-939-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

C1607 C1608 C1609 C1610 C1611

1-125-777-11 1-104-913-11 1-164-874-11 1-104-913-11 1-164-935-11

CERAMIC CHIP 0.1uF 10% 10V TANTAL. CHIP 10uF 20% 16V CERAMIC CHIP 100PF 5% 16V TANTAL. CHIP 10uF 20% 16V CERAMIC CHIP 470PF 10% 16V (TRV11/TRV11E/TRV20/TRV20E)

C1612 C1613 C1614 C1615 C1616

1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16V 1-104-913-11 TANTAL. CHIP 10uF 20% 16V (TRV11/TRV11E/TRV20/TRV20E) 1-119-751-11 TANTAL. CHIP 22uF 20% 16V 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V 1-119-751-11 TANTAL. CHIP 22uF 20% 16V

C1617 C1618 C1619 C1620 C1621

1-164-939-11 1-164-935-11 1-164-937-11 1-164-933-11 1-164-874-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.022uF 0.1uF 0.022uF 0.022uF 0.0022uF

0.0022uF 470PF 0.001uF 220PF 100PF

10% 10% 10% 10% 10%

10% 10% 10% 10% 5%

16V 10V 16V 16V 16V

16V 16V 16V 16V 16V

6-13

Remarks 1uF 4.7uF 4.7uF 0.0022uF 1uF

10% 10% 10% 10% 10%

10V 6.3V 6.3V 16V 10V

C1636

CERAMIC CHIP 0.0033uF 10% 16V CERAMIC CHIP 4.7uF 10% 10V CERAMIC CHIP 4.7uF 10% 10V CERAMIC CHIP 4.7uF 10% 10V (TRV11/TRV11E/TRV20/TRV20E) 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V

C1637 C1638 C1639 C1640 C1641

1-115-566-11 1-162-970-11 1-104-851-11 1-127-760-91 1-127-760-91

C1642 C1643 C1644 C1645 C1646

1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V (TRV11/TRV11E/TRV20/TRV20E) 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V 1-164-505-11 CERAMIC CHIP 2.2uF 16V

C1647 C1648 C1649 C1650 C1651

1-164-505-11 1-109-982-11 1-164-505-11 1-165-319-11 1-131-862-91

C1651

1-135-259-11 TANTAL. CHIP

C1652

1-135-259-11 TANTAL. CHIP

C1653 C1654

1-135-259-11 TANTAL. CHIP 1-119-750-11 TANTAL. CHIP

C1654

1-135-259-11 TANTAL. CHIP

C1655 C1656 C1657 C1658

1-164-505-11 1-135-259-11 1-104-851-11 1-135-259-11

CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP

< CAPACITOR > C1601 C1602 C1603 C1604 C1605

DD-137

4.7uF 0.01uF 10uF 4.7uF 4.7uF

2.2uF 1uF 2.2uF 0.1uF 47uF

10% 10% 20% 10% 10%

10V 25V 10V 6.3V 6.3V

16V 10V 16V 50V 20% 4V (TRV11/TRV11E)

10%

10uF 20% 6.3V (TRV6/TRV6E/TRV20/TRV20E) 10uF 20% 6.3V (TRV11/TRV11E/TRV20/TRV20E) 10uF 20% 6.3V 22uF 20% 6.3V (TRV6/TRV6E/TRV11/TRV11E) 10uF 20% 6.3V (TRV20/TRV20E)

C1659

CERAMIC CHIP 2.2uF 16V TANTAL. CHIP 10uF 20% 6.3V TANTAL. CHIP 10uF 20% 10V TANTAL. CHIP 10uF 20% 6.3V (TRV11/TRV11E/TRV20/TRV20E) 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V

C1660 C1661 C1662 C1663 C1664

1-135-259-11 1-104-851-11 1-104-851-11 1-125-777-11 1-104-851-11

TANTAL. CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP

C1666 C1667 C1668 C1669

1-113-985-11 1-164-505-11 1-164-505-11 1-125-777-11

TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

C1672

1-113-987-11 TANTAL. CHIP

10uF 10uF 10uF 0.1uF 10uF

20% 20% 20% 10% 20%

6.3V 10V 10V 10V 10V

10uF 20% 20V 2.2uF 16V 2.2uF 16V 0.1uF 10% 10V (TRV6/TRV6E/TRV11/TRV11E) 4.7uF 20% 25V

DD-137 Ref. No. C1673 C1674

Part No.

Description

Remarks

1-104-851-11 TANTAL. CHIP 1-164-943-11 CERAMIC CHIP

10uF 0.01uF

20% 10%

Ref. No.

10V 16V

L1616 L1617 L1618 L1619

< CONNECTOR > * CN1601 1-580-056-21 * CN1602 1-580-056-21 CN1603 1-779-520-11 CN1604 1-784-421-11

PIN, CONNECTOR (SMD) 3P PIN, CONNECTOR (SMD) 3P CONNECTOR, BOARD TO BOARD 80P CONNECTOR, FFC/FPC (ZIF) 27P

L1624

Part No.

Description

Remarks

1-469-522-91 1-414-400-11 1-469-058-11 1-414-770-91

INDUCTOR 1uH INDUCTOR 22uH INDUCTOR CHIP 22uH INDUCTOR CHIP 4.7uH (TRV11/TRV11E/TRV20/TRV20E) 1-414-770-91 INDUCTOR CHIP 4.7uH (TRV20/TRV20E) < LINE FILTER >

LF1601 1-411-957-11 FILTER, COMMON MODE < DIODE > < TRANSISTOR > D1601 D1602 D1604 D1606 D1607

8-719-158-49 8-719-062-16 8-719-056-48 8-719-058-24 8-719-058-24

DIODE DIODE DIODE DIODE DIODE

MA8120-TX 01ZA8.2(TPL3) 1SS388(TPL3) RB501V-40TE-17 RB501V-40TE-17

D1608 D1609 D1610 D1611 D1612

8-719-058-24 8-719-056-48 8-719-056-48 8-719-027-77 8-719-056-48

DIODE DIODE DIODE DIODE DIODE

RB501V-40TE-17 1SS388(TPL3) 1SS388(TPL3) MA796-TX 1SS388(TPL3) (TRV20/TRV20E)

D1613 D1614 D1615 D1616

8-719-056-48 8-719-056-23 8-719-075-12 8-719-056-23

DIODE DIODE DIODE DIODE

1SS388(TPL3) MA2S111-(K8).SO MA3XD21001S0 MA2S111-(K8).SO

< FUSE > 0 F1601 0 F1602 0 F1603 0 F1604 0 F1605

1-576-406-21 1-576-406-21 1-576-406-21 1-576-406-21 1-576-406-21

0 F1606

1-576-406-21 FUSE, MICRO (1608) (1.4A 32V)

FUSE, MICRO (1608) (1.4A 32V) FUSE, MICRO (1608) (1.4A 32V) FUSE, MICRO (1608) (1.4A 32V) FUSE, MICRO (1608) (1.4A 32V) FUSE, MICRO (1608) (1.4A 3.2V) (TRV11/TRV11E/TRV20/TRV20E)

< IC > IC1601 IC1602

8-759-678-75 IC MB4488PFV-G-BND-ER-F 8-759-075-66 IC TA75S01F(TE85R) < COIL >

L1601 L1602 L1603 L1604

1-416-669-11 1-416-670-11 1-416-669-11 1-416-669-11

INDUCTOR INDUCTOR INDUCTOR INDUCTOR

L1605

1-416-669-11 INDUCTOR

L1606 L1607

1-416-669-11 INDUCTOR 1-414-392-21 INDUCTOR

L1608 L1609 L1610

1-414-392-21 INDUCTOR 1-412-056-11 INDUCTOR 1-414-392-21 INDUCTOR

L1611 L1612 L1613 L1614 L1615

1-414-392-21 1-414-770-91 1-414-770-91 1-469-522-91 1-469-522-91

22uH 33uH 22uH 22uH (TRV11/TRV11E/TRV20/TRV20E) 22uH 22uH 1uH (TRV11/TRV11E/TRV20/TRV20E) 1uH 4.7uH 1uH

INDUCTOR INDUCTOR CHIP INDUCTOR CHIP INDUCTOR INDUCTOR

1uH 4.7uH 4.7uH 1uH 1uH

6-14

Q1601 Q1602 Q1603 Q1604 Q1605

8-729-047-68 8-729-046-77 8-729-804-41 8-729-037-74 8-729-050-24

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

SSM3K03FE(TPL3) SI4963DY-T1 2SB1122-ST-TD UN9213J-(K8).SO MCH6202-TL

Q1606 Q1607 Q1608 Q1609 Q1610

8-729-037-53 8-729-037-74 8-729-050-23 8-729-046-98 8-729-046-98

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

2SB1462J-QR(K8).SO UN9213J-(K8).SO MCH6103-TL CPH6702-TL CPH6702-TL

Q1611 Q1612

8-729-046-98 TRANSISTOR 8-729-046-98 TRANSISTOR

Q1613 Q1614 Q1615

CPH6702-TL CPH6702-TL (TRV11/TRV11E/TRV20/TRV20E) 8-729-046-98 TRANSISTOR CPH6702-TL 8-729-046-98 TRANSISTOR CPH6702-TL 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO

Q1616 Q1617 Q1618 Q1619 Q1620

8-729-017-61 8-729-037-53 8-729-044-58 8-729-044-58 8-729-044-58

Q1621

8-729-044-58 TRANSISTOR

Q1622 Q1623 Q1624 Q1625

8-729-044-58 8-729-044-58 8-729-037-52 8-729-037-74

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

Q1626 Q1627 Q1628 Q1629 Q1632

8-729-042-56 8-729-049-91 8-729-037-52 8-729-037-74 8-729-037-53

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

MGSF3455VT1 2SA2018H-T2L 2SD2216J-QR(K8).SO UN9213J-(K8).SO 2SB1462J-QR(K8).SO

Q1635 Q1637 Q1639 Q1641 Q1643

8-729-037-53 8-729-037-52 8-729-037-52 8-729-037-53 8-729-037-53

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

2SB1462J-QR(K8).SO 2SD2216J-QR(K8).SO 2SD2216J-QR(K8).SO 2SB1462J-QR(K8).SO 2SB1462J-QR(K8).SO

Q1646

8-729-037-74 TRANSISTOR

Q1647

8-729-037-52 TRANSISTOR

Q1648

8-729-037-74 TRANSISTOR

Q1649

8-729-037-52 TRANSISTOR

Q1650

8-729-037-53 TRANSISTOR

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

2SB1581-T1 2SB1462J-QR(K8).SO SI2304DS-T1 SI2304DS-T1 SI2304DS-T1 SI2304DS-T1 (TRV11/TRV11E/TRV20/TRV20E) SI2304DS-T1 SI2304DS-T1 2SD2216J-QR(K8).SO UN9213J-(K8).SO

UN9213J-(K8).SO (TRV20/TRV20E) 2SD2216J-QR(K8).SO (TRV6/TRV6E/TRV11/TRV11E) UN9213J-(K8).SO (TRV20/TRV20E) 2SD2216J-QR(K8).SO (TRV6/TRV6E/TRV11/TRV11E) 2SB1462J-QR(K8).SO (TRV6/TRV6E/TRV11/TRV11E) Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

DD-137 Ref. No. Q1653

Part No.

Description

8-729-037-52 TRANSISTOR

Remarks

Ref. No.

2SD2216J-QR(K8).SO (TRV6/TRV6E/TRV11/TRV11E)

< RESISTOR > R1601 R1602 R1603 R1604 R1605

1-218-953-11 1-218-985-11 1-218-989-11 1-216-150-91 1-218-953-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

R1606 R1609

1-218-961-11 RES-CHIP 1-218-990-11 SHORT

1K 470K 1M 10 1K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/8W 1/16W

R1610 R1611 R1612

4.7K 5% 1/16W 0 (TRV11/TRV11E/TRV20/TRV20E) 1-218-961-11 RES-CHIP 4.7K 5% 1/16W 1-218-969-11 RES-CHIP 22K 5% 1/16W 1-208-715-11 METAL CHIP 22K 0.5% 1/16W

R1613

1-208-927-11 METAL CHIP

R1614

1-218-969-11

R1615 R1616 R1617

1-218-965-11 1-208-707-11 1-208-931-11

R1618 R1619

1-218-970-11 RES-CHIP 1-218-849-11 METAL CHIP

47K 0.5% 1/16W (TRV11/TRV11E/TRV20/TRV20E) RES-CHIP 22K 5% 1/16W (TRV11/TRV11E/TRV20/TRV20E) RES-CHIP 10K 5% 1/16W METAL CHIP 10K 0.5% 1/16W METAL CHIP 68K 0.5% 1/16W (TRV11/TRV11E/TRV20/TRV20E)

R1620 R1621 R1622

27K 5% 1/16W 3.3K 0.5% 1/16W (TRV11/TRV11E/TRV20/TRV20E) 1-218-973-11 RES-CHIP 47K 5% 1/16W 1-218-965-11 RES-CHIP 10K 5% 1/16W 1-208-927-11 METAL CHIP 47K 0.5% 1/16W

R1623 R1624 R1625 R1626 R1627

1-218-969-11 1-208-927-11 1-218-965-11 1-218-971-11 1-208-715-11

RES-CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP

R1628 R1629 R1630 R1631

1-218-974-11 1-218-974-11 1-208-715-11 1-208-933-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP

R1631

1-208-935-11 METAL CHIP

R1632 R1633 R1634 R1635 R1636

1-218-945-11 1-218-849-11 1-208-697-11 1-208-697-11 1-208-707-11

R1636

1-208-711-11 METAL CHIP

R1637

1-218-941-11 RES-CHIP

R1638 R1639 R1640

1-218-941-11 RES-CHIP 1-218-941-11 RES-CHIP 1-218-941-11 RES-CHIP

R1641 R1642 R1643 R1644 R1645

1-218-953-11 1-218-953-11 1-218-941-11 1-218-941-11 1-218-973-11

RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

22K 47K 10K 33K 22K

5% 0.5% 5% 5% 0.5%

1/16W 1/16W 1/16W 1/16W 1/16W

56K 0.5% 1/16W 56K 0.5% 1/16W 22K 0.5% 1/16W 82K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 100K 0.5% 1/16W (TRV20/TRV20E) 220 3.3K 3.9K 3.9K 10K

5% 1/16W 0.5% 1/16W 0.5% 1/16W 0.5% 1/16W 0.5% 1/16W (TRV20/TRV20E)

15K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 100 5% 1/16W (TRV11/TRV11E/TRV20/TRV20E) 100 5% 1/16W 100 5% 1/16W 100 5% 1/16W 1K 1K 100 100 47K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

6-15

Part No.

Description

R1646 R1647 R1648 R1649 R1650

1-218-965-11 1-208-715-11 1-208-719-11 1-218-965-11 1-218-989-11

RES-CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP

R1651

1-218-990-11 SHORT

R1652 R1653 R1654 R1655

1-218-977-11 1-218-973-11 1-218-969-11 1-218-949-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP

R1656 R1657 R1658 R1661 R1662

1-218-969-11 1-208-719-11 1-208-936-81 1-218-977-11 1-218-977-11

RES-CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP

R1664 R1666 R1668

1-218-969-11 RES-CHIP 1-218-969-11 RES-CHIP 1-218-990-11 SHORT

R1669 R1672

1-218-990-11 SHORT 1-208-927-11 METAL CHIP

R1673 R1674 R1675 R1676

1-218-982-11 1-208-935-11 1-208-935-11 1-208-707-11

R1676

1-208-715-11 METAL CHIP

R1677 R1678 R1679 R1680

1-208-943-11 1-218-849-11 1-218-990-11 1-218-973-11

R1682

1-218-953-11 RES-CHIP

R1683

1-218-952-11 RES-CHIP

R1684

1-218-977-11 RES-CHIP

R1685

1-218-969-11 RES-CHIP

R1686

1-218-969-11 RES-CHIP

R1687

1-218-952-11 RES-CHIP

R1688

1-218-952-11 RES-CHIP

R1689

1-208-713-11 METAL CHIP

R1690

1-208-935-11 METAL CHIP

R1691

1-208-927-11 METAL CHIP

R1692

1-218-952-11 RES-CHIP

R1693 R1694 R1695 R1696 R1697

1-217-671-11 1-217-671-11 1-218-982-11 1-218-973-11 1-218-969-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP

METAL CHIP METAL CHIP SHORT RES-CHIP

METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP

Remarks 10K 22K 33K 10K 1M

5% 0.5% 0.5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

0 (TRV6/TRV6E/TRV11/TRV11E) 100K 5% 1/16W 47K 5% 1/16W 22K 5% 1/16W 470 5% 1/16W 22K 33K 110K 100K 100K

5% 0.5% 0.5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

22K 5% 1/16W 22K 5% 1/16W 0 (TRV6/TRV6E/TRV11/TRV11E) 0 (TRV20/TRV20E) 47K 0.5% 1/16W 270K 100K 100K 10K

0.5% 1/16W 0.5% 1/16W 0.5% 1/16W 0.5% 1/16W (TRV20/TRV20E) 22K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 220K 0.5% 1/16W 1.2K 0.5% 1/16W 0 47K 5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 1K 5% 1/16W 820

5% 1/16W (TRV20/TRV20E) 100K 5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 22K 5% 1/16W (TRV20/TRV20E) 22K 5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 820 5% 1/16W (TRV20/TRV20E) 820

5% 1/16W (TRV20/TRV20E) 18K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 100K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 47K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 820 5% 1/16W (TRV20/TRV20E) 1 1 270K 47K 22K

5% 5% 5% 5% 5%

1/10W 1/10W 1/16W 1/16W 1/16W

DD-137 Ref. No. R1698 R1699 R1700 R1701 R1702

FP-102

Part No.

Description

1-218-969-11 1-218-969-11 1-218-969-11 1-218-969-11 1-218-953-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

FP-219

JK-188 Remarks

22K 22K 22K 22K 1K

5% 5% 5% 5% 5%

Ref. No.

1/16W 1/16W 1/16W 1/16W 1/16W

C3063 C3064 C3065 C3066 C3067

Part No.

Description

1-125-817-11 1-125-817-11 1-110-501-11 1-104-847-11 1-125-777-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP

< TRANSFORMER >

10% 10% 10% 20% 10%

6.3V 6.3V 16V 4V 10V

< CONNECTOR >

T1601 1-435-456-21 TRANSFORMER, DC-DC CONVERTER T1602 1-435-456-21 TRANSFORMER, DC-DC CONVERTER ************************************************************

D901

Remarks 10uF 10uF 0.33uF 22uF 0.1uF

CN3001 1-784-939-11 CONNECTOR, BOARD TO BOARD 60P < DIODE >

FP-102 FLEXIBLE (Not supplied) ************************** (Ref.No.;6000Series)

D3001

< DIODE >

FB3004 FB3005 FB3007 FB3008

8-719-078-71 DIODE LN57A.SO

8-719-056-61 DIODE 015AZ8.2-TPL3 < FERRITE BEAD > 1-500-444-11 1-500-444-11 1-500-444-11 1-500-444-11

FERRITE FERRITE FERRITE FERRITE

0UH 0UH 0UH 0UH

< HOLE ELEMENT > < IC > H901 H902

8-719-067-74 DIODE HW-105A-CDE-T 8-719-067-74 DIODE HW-105A-CDE-T

IC3051

8-759-489-19 IC uPC6756GR-8JG-E2

< TRANSISTOR > Q901 Q902

8-729-028-71 TRANSISTOR 8-729-028-71 TRANSISTOR

< JACK > PN166.SO PN166.SO

J3001 J3002 J3003 J3004

< SWITCH >

1-778-518-11 1-695-514-21 1-778-040-11 1-794-276-11

S903 1-771-326-41 SWITCH, PUSH (1KEY) (CC DOWN) ************************************************************

< COIL > L3052

1-677-566-21 FP-219 FLEXIBLE, COMPLETE (TRV6/TRV6E/TRV11/TRV11E) ************************************** (Ref.No.;30000Series) (All parts excluding CCD are already mounted of the FP-219 FLEXIBLE, COMPLETE.) (IC3000 is not included in this complete board.)

CONNECTOR, EXTERNAL (S VIDEO) JACK (SMALL TYPE) 1P (i) JACK, SMALL TYPE (AUDIO/VIDEO) CONNECTOR, SQUARE TYPE 4P (DV IN/OUT)

1-414-771-91 INDUCTOR CHIP 10uH < RESISTOR >

R3001 R3002 R3003 R3004 R3005

1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

0 0 0 0 0

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

R3051 R3052 R3053 R3054 R3055

1-218-969-11 1-218-969-11 1-218-969-11 1-218-969-11 1-218-965-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

22K 22K 22K 22K 10K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

R3056 R3057 R3058 R3059 R3060

1-218-965-11 1-218-989-11 1-218-967-11 1-218-989-11 1-218-953-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

10K 1M 15K 1M 1K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

R3061

1-216-295-91 SHORT

< IC > IC3000 A-7031-011-A CCD BLOCK ASSY (TRV6/TRV11) IC3000 A-7031-012-A CCD BLOCK ASSY (TRV6E/TRV11E) ************************************************************ A-7074-309-A JK-188 BOARD, COMPLETE ********************** (Ref.No.;10000Series) < CAPACITOR > C3053 C3054 C3055 C3056 C3057

1-104-847-11 1-104-847-11 1-125-777-11 1-125-777-11 1-119-923-81

TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

22uF 22uF 0.1uF 0.1uF 0.047uF

20% 20% 10% 10% 10%

4V 4V 10V 10V 10V

C3058 C3059 C3060 C3061 C3062

1-119-923-81 1-119-923-81 1-119-923-81 1-125-817-11 1-125-817-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.047uF 0.047uF 0.047uF 10uF 10uF

10% 10% 10% 10% 10%

10V 10V 10V 6.3V 6.3V

0

< SENSOR > SE3051 1-803-042-31 SENSOR, ANGULAR VELOCITY (PITCH) SE3052 1-803-042-41 SENSOR, ANGULAR VELOCITY (YAW) < VARISTOR > VDR001 VDR002 VDR003 VDR004 VDR005

Be sure to read “Precautions upon replacing CCD imager” on page 4-14 when changing the CCD imager.

6-16

1-801-862-11 1-801-862-11 1-801-862-11 1-801-862-11 1-803-742-21

VARISTOR, CHIP VARISTOR, CHIP VARISTOR, CHIP VARISTOR, CHIP VARISTOR, CHIP

JK-188 Ref. No.

Part No.

Description

Remarks

Ref. No.

VDR006 1-803-742-21 VARISTOR, CHIP VDR007 1-803-742-21 VARISTOR, CHIP ************************************************************ A-7074-310-A LB-64 BOARD, COMPLETE ********************* (Ref.No.;10000Series) < CAPACITOR > C2201 C2202 C2203 0 C2204

1-125-777-11 1-113-682-11 1-115-566-11 1-115-464-91

CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP

0.1uF 33uF 4.7uF 0.0022uF

10% 20% 10% 10%

10V 10V 10V 630V

< CONNECTOR > CN2201 1-784-421-11 CONNECTOR, FFC/FPC (ZIF) 27P CN2201 1-784-421-11 CONNECTOR, FPC (ZIF) 27P CN2202 1-691-380-21 CONNECTOR, FFC/FPC 16P < IC > IC2201

1-412-031-11 INDUCTOR CHIP 47uH 1-469-525-91 INDUCTOR 10uH < FLUORESCENT INDICATOR >

0 ND2201 1-517-933-31 FLUORESCENT TUBE (0.44) < TRANSISTOR > 0 Q2201

8-729-039-24 TRANSISTOR

Part No.

Description

C2015 C2017 C2018 C2020 C2021

1-164-937-11 1-164-874-11 1-164-874-11 1-125-777-11 1-125-777-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.001uF 100PF 100PF 0.1uF 0.1uF

10% 5% 5% 10% 10%

16V 16V 16V 10V 10V

C2022 C2023 C2024 C2025 C2026

1-125-777-11 1-110-563-11 1-125-777-11 1-110-563-11 1-164-227-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.1uF 0.068uF 0.1uF 0.068uF 0.022uF

10% 10% 10% 10% 10%

10V 16V 10V 16V 25V

C2027 C2028 C2029 C2031 C2032

1-164-227-11 1-164-245-11 1-164-940-11 1-164-940-11 1-164-245-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.022uF 0.015uF 0.0033uF 0.0033uF 0.015uF

10% 10% 10% 10% 10%

25V 25V 16V 16V 25V

C2036 C2037 C2038 C2039 C2041

1-125-777-11 1-117-919-11 1-165-128-11 1-125-841-91 1-164-937-11

CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP

0.1uF 10uF 0.22uF 22uF 0.001uF

10% 20% 20% 10%

10V 6.3V 16V 4V 16V

C2042 C2043 C2044 C2045 C2046

1-164-937-11 1-164-939-11 1-125-777-11 1-125-777-11 1-125-777-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.001uF 0.0022uF 0.1uF 0.1uF 0.1uF

10% 10% 10% 10% 10%

16V 16V 10V 10V 10V

C2047 C2071 C2072 C2073 C2091

1-125-777-11 1-107-826-91 1-104-913-11 1-107-826-91 1-117-919-11

CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP

0.1uF 0.1uF 10uF 0.1uF 10uF

10% 10% 20% 10% 20%

10V 16V 16V 16V 6.3V

Remarks

< CONNECTOR >

FX216-TL1

CN2001 1-778-507-21 PIN, CONNECTOR (PC BOARD) 4P CN2051 1-778-793-21 CONNECTOR, FFC/FPC (ZIF) 5P CN2071 1-764-534-21 CONNECTOR, FFC/FPC (ZIF) 28P

< RESISTOR > R2203 R2205

MA-385

8-759-485-79 IC TC7SET08FU(TE85R) < COIL >

L2201 L2202

LB-64

1-216-808-11 METAL CHIP 1-218-965-11 RES-CHIP

82 10K

5% 5%

1/16W 1/16W

< DIODE > < TRANSFORMER > 0 T2201 1-435-225-21 TRANSFORMER, INVERTER ************************************************************ A-7074-308-A MA-385 BOARD, COMPLETE *********************** (Ref.No.;10000Series) 3-061-599-01 HOLDER (3015), LED

*

D2001 D2002 D2061 D2062 D2063

8-719-062-16 8-719-062-16 8-719-061-82 8-719-062-16 8-719-072-91

DIODE DIODE DIODE DIODE DIODE

01ZA8.2(TPL3) 01ZA8.2(TPL3) TLSU1002(TPX1,SONY) 01ZA8.2(TPL3) MAZJ200D0LS0

D2071 D2072 D2091

8-719-060-65 DIODE DAC3825 8-719-078-23 DIODE DCR2815 8-719-056-23 DIODE MA2S111-(K8).SO < FERRITE BEAD >

< CAPACITOR > C2005 C2006 C2007 C2008 C2009

1-107-819-11 1-164-941-11 1-107-819-11 1-164-943-11 1-164-941-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.022uF 0.0047uF 0.022uF 0.01uF 0.0047uF

10% 10% 10% 10% 10%

16V 16V 16V 16V 16V

C2010 C2011 C2012 C2013 C2014

1-117-919-11 1-164-937-11 1-117-919-11 1-164-874-11 1-164-874-11

TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP

10uF 0.001uF 10uF 100PF 100PF

20% 10% 20% 5% 5%

6.3V 16V 6.3V 16V 16V

FB2001 FB2002 FB2003 FB2061

1-500-444-11 1-500-444-11 1-500-444-11 1-216-864-11

FERRITE FERRITE FERRITE METAL CHIP

0UH 0UH 0UH 0

FB2062 1-500-444-11 FERRITE

0UH

FB2063 1-500-444-11 FERRITE FB2064 1-500-444-11 FERRITE

0UH 0UH

5%

1/16W (Note)

Note : Resistor is mounted to the location where FB2061 is printed.

6-17

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

MA-385 Ref. No.

NS-10

Part No.

PD-123

Description

Remarks

Ref. No.

< IC > IC2002 IC2091

8-759-638-50 IC AN2901FHQ-EB 8-749-013-13 IC RS-70-TU

Part No.

Description

R2065 R2071 R2072 R2073 R2074

1-218-949-11 1-218-932-11 1-216-001-00 1-218-973-11 1-218-953-11

RES-CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP

R2075 R2091

1-216-795-11 RES-CHIP 1-218-937-11 RES-CHIP

Remarks 470 18 10 47K 1K

5% 5% 5% 5% 5%

1/16W 1/16W 1/10W 1/16W 1/16W

6.8 47

5% 5%

1/16W 1/16W

< JACK > J2001 J2002

1-691-737-11 JACK (SMALL TYPE) (MIC) 1-793-995-11 JACK, SUPER SMALL TYPE (DIGITAL I/O) (LANC)

< SWITCH >

< COIL > L2001

1-414-754-11 INDUCTOR

S2061

< VARISTOR >

10uH

< TRANSISTOR > Q2071 Q2072 Q2073 Q2074

8-729-140-75 8-729-141-48 8-729-037-72 8-729-037-53

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

1-762-651-11 SWITCH, SLIDE

VDR201 1-803-742-21 VARISTOR, CHIP ************************************************************ 2SD999-T1-CLCK 2SB624-T1BV4 UN9211J-(TX).SO 2SB1462J-QR(TX).SO

A-7074-312-A NS-10 BOARD, COMPLETE (TRV20/TRV20E) *********************************** (Ref.No.;4000Series) < SWITCH >

< RESISTOR >

S001 1-771-138-61 SWITCH, KEY BOARD (SLOW SHUTTER) ************************************************************

R2007 R2008 R2009 R2010 R2011

1-218-968-11 1-218-971-11 1-218-961-11 1-218-965-11 1-218-957-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

18K 33K 4.7K 10K 2.2K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

R2012 R2013 R2014 R2015 R2016

1-218-957-11 1-218-963-11 1-218-963-11 1-218-953-11 1-218-953-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

2.2K 6.8K 6.8K 1K 1K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

R2017 R2018 R2019 R2020 R2021

1-218-957-11 1-218-957-11 1-208-910-11 1-218-969-11 1-208-910-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

2.2K 2.2K 9.1K 22K 9.1K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

C2101 C2102 C2105 C2106 C2107

1-113-988-11 1-125-777-11 1-164-943-11 1-164-943-11 1-164-943-11

TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

68uF 0.1uF 0.01uF 0.01uF 0.01uF

20% 10% 10% 10% 10%

4V 10V 16V 16V 16V

R2022 R2023 R2024 R2025 R2026

1-218-969-11 1-218-970-11 1-218-990-11 1-218-990-11 1-218-970-11

RES-CHIP RES-CHIP SHORT SHORT RES-CHIP

22K 27K 0 0 27K

5% 5%

1/16W 1/16W

5%

1/16W

C2108 C2109 C2110 C2111 C2112

1-135-259-11 1-125-777-11 1-125-777-11 1-107-687-11 1-107-826-91

TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP

10uF 0.1uF 0.1uF 3.3uF 0.1uF

20% 10% 10% 20% 10%

6.3V 10V 10V 20V 16V

R2027 R2028 R2031 R2032 R2033

1-218-969-11 1-218-969-11 1-218-971-11 1-218-954-11 1-218-971-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

22K 22K 33K 1.2K 33K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

C2113 C2114 C2115 C2116 C2117

1-164-739-11 1-125-777-11 1-125-777-11 1-104-851-11 1-164-357-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP

560PF 0.1uF 0.1uF 10uF 1000PF

5% 10% 10% 20% 5%

50V 10V 10V 10V 50V

R2034 R2035 R2036 R2037 R2038

1-218-968-11 1-218-990-11 1-208-912-11 1-208-912-11 1-208-701-11

RES-CHIP SHORT METAL CHIP METAL CHIP METAL CHIP

18K 0 11K 11K 5.6K

5%

1/16W

C2118

1-164-866-11 CERAMIC CHIP

47PF

5%

0.5% 0.5% 0.5%

1/16W 1/16W 1/16W

C2118

1-164-872-11 CERAMIC CHIP

82PF

R2051 R2052 R2062 R2063 R2064

1-218-945-11 1-218-945-11 1-218-966-11 1-218-969-11 1-218-952-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

220 220 12K 22K 820

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

C2119 C2120 C2121

1-109-982-11 CERAMIC CHIP 1-109-982-11 CERAMIC CHIP 1-109-982-11 CERAMIC CHIP

1uF 1uF 1uF

C2122 C2123 C2124 C2125 C2127

1-113-994-11 1-125-777-11 1-125-777-11 1-107-682-11 1-135-177-21

6.8uF 0.1uF 0.1uF 1uF 1uF

A-7074-314-A PD-123(CA) BOARD, COMPLETE (TRV20) ********************************* A-7074-367-A PD-123 (SH) BOARD, COMPLETE (TRV11/TRV11E) ************************************** (Ref.No.;20000Series) < CAPACITOR >

6-18

TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP

16V (TRV20) 5% 16V (TRV11/TRV11E) 10% 10V 10% 10V 10% 10V 20% 16V 10% 10V 10% 10V 10% 16V 20% 20V (TRV11/TRV11E)

PD-123 Ref. No.

Part No.

Description

C2128 C2129 C2130 C2131

1-107-826-91 1-164-943-11 1-107-682-11 1-164-943-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.1uF 0.01uF 1uF 0.01uF

C2132

1-164-943-11 CERAMIC CHIP

0.01uF

C2172 C2173 C2174 C2175 C2180

1-127-985-91 1-107-826-91 1-117-919-11 1-125-777-11 1-162-970-11

47uF 0.1uF 10uF 0.1uF 0.01uF

TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP

Remarks

Ref. No.

1-750-344-11 1-785-283-21 1-785-554-21 1-784-420-11 1-779-064-11

Description

Remarks

R2101 R2103 R2105 R2106 R2107

1-218-990-11 1-218-990-11 1-218-985-11 1-208-719-11 1-218-970-11

SHORT SHORT RES-CHIP METAL CHIP METAL CHIP

0 0 470K 33K 27K

(TRV20) (TRV11/TRV11E) 5% 1/16W 0.5% 1/16W 0.5% 1/16W

20% 10% 20% 10% 10%

R2111 R2112 R2113 R2114 R2116

1-218-977-11 1-216-835-11 1-218-958-11 1-218-973-11 1-218-975-11

RES-CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP

100K 15K 2.7K 47K 68K

5% 5% 5% 5% 5%

R2117 R2118 R2119 R2120 R2121

1-218-969-11 1-218-975-11 1-218-989-11 1-218-977-11 1-218-989-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

22K 68K 1M 100K 1M

5% 1/16W 5% 1/16W 5% 1/16W 5% 1/16W 5% 1/16W (TRV11/TRV11E)

R2122

1-218-974-11 RES-CHIP

56K

5%

R2123 R2124 R2125 R2126

1-218-990-11 1-218-990-11 1-500-284-21 1-218-990-11

SHORT SHORT INDUCTOR CHIP SHORT

0 (TRV20) 0 (TRV11/TRV11E) 0UH (Note) 0 (TRV20)

R2127 R2129 R2133 R2134 R2135

1-218-942-11 1-218-965-11 1-218-941-11 1-218-941-11 1-218-941-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP

120 10K 100 100 100

5% 5% 5% 5% 5%

R2140 R2141 R2142 R2143

1-218-990-11 1-218-965-11 1-218-985-11 1-218-980-11

SHORT RES-CHIP RES-CHIP RES-CHIP

0 10K 470K 180K

R2144

1-218-990-11 SHORT

0

(TRV20) 5% 1/16W 5% 1/16W 5% 1/16W (TRV11/TRV11E) (TRV20)

R2146 R2147

1-218-990-11 SHORT 1-218-965-11 RES-CHIP

0 10K

3.3uH (TRV11/TRV11E) 4.7uH 100uH

R2148

1-218-973-11 RES-CHIP

47K

R2149 R2150

1-218-990-11 SHORT 1-218-989-11 RES-CHIP

0 1M

MGSF1P02LT1 (TRV11/TRV11E) 2SB1462J-QR(K8).SO (TRV11/TRV11E) 2SD2216J-QR(K8).SO (TRV11/TRV11E) 2SB1462J-QR(K8).SO (TRV11/TRV11E) 2SD2216J-QR(K8).SO (TRV11/TRV11E)

R2151

1-218-989-11 RES-CHIP

1M

R2152 R2153 R2154 R2175

1-218-990-11 1-218-990-11 1-218-990-11 1-218-961-11

0 0 0 4.7K

< RESISTOR >

16V 16V 6.3V 10V 25V

< CONNECTOR > CN2101 CN2173 CN2174 CN2175 CN2176

Part No.

10% 16V 10% 16V 10% 16V 10% 16V (TRV11/TRV11E) 10% 16V (TRV11/TRV11E)

CONNECTOR, FFC/EPC (ZIF) 24P PIN, CONNECTOR (PC BOARD) 14P CONNECTOR (5P), CARD EDGE CONNECTOR, FFC/FPC (ZIF) 21P PIN, CONNECTOR (PC BOARD) 12P < DIODE >

D2101 D2102 D2103

8-719-073-01 DIODE MA111-TX 8-713-102-80 DIODE 1T369-01-T8A 8-719-073-01 DIODE MA111-TX (TRV11/TRV11E) < IC >

IC2104 IC2105 IC2105 IC2106 IC2171

8-759-660-92 8-759-591-93 8-759-660-91 8-759-478-92 8-759-573-02

IC IC IC IC IC

RB5P003AM1 CM7019L3-T4 (TRV20) LZ9FF424 (TRV11/TRV11E) TC7SET04FU(TE85R) (TRV11/TRV11E) BU9735K-E2

< COIL > L2101 L2102 L2103 L2104 L2105

1-469-525-91 1-414-771-91 1-414-771-91 1-414-771-91 1-412-943-11

INDUCTOR INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR

L2105 L2172 L2173

1-412-945-11 INDUCTOR 1-412-056-11 INDUCTOR 1-414-757-11 INDUCTOR

10uH 10uH 10uH 10uH 2.2uH (TRV20)

< TRANSISTOR > Q2102

8-729-041-23 TRANSISTOR

Q2103

8-729-037-53 TRANSISTOR

Q2104

8-729-037-52 TRANSISTOR

Q2105

8-729-037-53 TRANSISTOR

Q2106

8-729-037-52 TRANSISTOR

Q2107 Q2108 Q2172 Q2173

8-729-037-52 8-729-037-74 8-729-042-72 8-729-037-53

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

SHORT SHORT SHORT RES-CHIP

1/16W 1/16W 1/16W 1/16W 1/16W

1/16W (TRV20)

1/16W 1/16W 1/16W 1/16W 1/16W

(TRV20) 5% 1/16W (TRV11/TRV11E) 5% 1/16W (TRV11/TRV11E) (TRV20) 5% 1/16W (TRV11/TRV11E) 5% 1/16W (TRV11/TRV11E)

5%

1/16W

R2176 1-218-953-11 RES-CHIP 1K 5% 1/16W R2177 1-216-864-11 METAL CHIP 0 5% 1/16W R2180 1-216-855-11 METAL CHIP 680K 5% 1/16W ************************************************************

2SD2216J-QR(K8).SO UN9213J-(K8).SO UN9214J-(K8).SO 2SB1462J-QR(K8).SO

Note : Inductor is mounted to the location where R2125 is printed.

6-19

PD-124 Ref. No.

Part No.

Description

Remarks

Ref. No.

A-7074-394-A PD-124(ST2) BOARD, COMPLETE (TRV6/TRV6E) ************************************** A-7074-397-A PD-124(ST3) BOARD, COMPLETE (TRV20E) ********************************** (Ref.No.;30000Series)

Part No.

Description

Remarks

< DIODE > D3101 D3102 D3103 D3104 D3105

8-719-073-01 8-713-102-80 8-719-050-39 8-719-050-44 8-719-073-01

DIODE DIODE DIODE DIODE DIODE

MA111-TX 1T369-01-T8A RD2.7UM-T1B RD3.3UM-T1B2 MA111-TX

(TRV20E) (TRV6/TRV6E)

< CAPACITOR > < IC > C3101 C3102 C3104 C3105 C3106

1-113-988-11 1-125-777-11 1-117-919-11 1-164-943-11 1-125-777-11

TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP

68uF 0.1uF 10uF 0.01uF 0.1uF

20% 10% 20% 10% 10%

4V 10V 6.3V 16V 10V

C3107 C3108 C3109 C3110 C3111

1-164-943-11 1-164-943-11 1-164-943-11 1-164-943-11 1-107-826-91

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.01uF 0.01uF 0.01uF 0.01uF 0.1uF

10% 10% 10% 10% 10%

16V 16V 16V 16V 16V

C3112 C3113 C3114 C3115 C3116

1-164-739-11 1-164-357-11 1-109-982-11 1-164-004-11 1-164-943-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

560PF 1000PF 1uF 0.1uF 0.01uF

5% 5% 10% 10% 10%

50V 50V 10V 25V 16V

C3117

1-164-864-11 CERAMIC CHIP

39PF

5%

C3117

1-164-866-11 CERAMIC CHIP

47PF

C3118 C3119 C3120

1-107-687-11 TANTAL. CHIP 1-109-982-11 CERAMIC CHIP 1-109-982-11 CERAMIC CHIP

3.3uF 1uF 1uF

C3121 C3126 C3127 C3128 C3129

1-109-982-11 1-107-826-91 1-164-943-11 1-164-506-11 1-109-982-11

1uF 0.1uF 0.01uF 4.7uF 1uF

IC3101 IC3102 IC3171

8-759-660-93 IC RB5P004AM1 8-752-403-84 IC CXD3505R-T4 8-759-573-02 IC BU9735K-E2 < COIL >

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

10%

10V 16V 16V 16V 10V (TRV20E)

C3130 C3131 C3132

1-107-725-11 CERAMIC CHIP 1-107-826-91 CERAMIC CHIP 1-109-982-11 CERAMIC CHIP

0.1uF 0.1uF 1uF

C3133 C3134

1-164-876-11 CERAMIC CHIP 1-164-876-11 CERAMIC CHIP

120PF 120PF

10% 16V 10% 16V 10% 10V (TRV6/TRV6E) 5% 16V 5% 16V

C3135 C3136 C3137 C3171 C3173

1-164-876-11 1-125-777-11 1-125-777-11 1-162-970-11 1-127-985-91

120PF 0.1uF 0.1uF 0.01uF 47uF

5% 10% 10% 10% 20%

16V 10V 10V 25V 16V

C3174 C3175 C3176

1-107-826-91 CERAMIC CHIP 1-117-919-11 TANTAL. CHIP 1-125-777-11 CERAMIC CHIP

0.1uF 10uF 0.1uF

10% 20% 10%

16V 6.3V 10V

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP

< CONNECTOR > CN3101 CN3171 CN3172 CN3173 CN3174

1-750-344-11 1-779-064-11 1-785-283-21 1-784-420-11 1-785-554-21

1-414-771-91 1-414-754-11 1-414-771-91 1-412-943-11 1-412-945-11

INDUCTOR CHIP INDUCTOR INDUCTOR CHIP INDUCTOR INDUCTOR

L3171 L3172

1-412-056-11 INDUCTOR 1-414-757-11 INDUCTOR

10uH 10uH 10uH 2.2uH 3.3uH

(TRV20E) (TRV6/TRV6E)

4.7uH 100uH

< TRANSISTOR >

16V (TRV20E) 5% 16V (TRV6/TRV6E) 20% 20V 10% 10V 10% 10V 10% 10% 10%

L3101 L3102 L3103 L3104 L3104

CONNECTOR, FFC/EPC (ZIF) 24P PIN, CONNECTOR (PC BOARD) 12P PIN, CONNECTOR (PC BOARD) 14P CONNECTOR, FFC/FPC (ZIF) 21P CONNECTOR (5P), CARD EDGE

6-20

Q3102 Q3103 Q3104 Q3105 Q3106

8-729-037-74 8-729-041-23 8-729-037-53 8-729-427-74 8-729-427-74

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

UN9213J-(TX).SO NDS356AP 2SB1462J-QR(K8).SO XP4601-TXE XP4601-TXE

Q3107 Q3108 Q3171 Q3172

8-729-037-52 8-729-037-74 8-729-042-72 8-729-037-53

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

2SD2216J-QR(K8).SO UN9213J-(TX).SO UN9214J-(K8).SO 2SB1462J-QR(K8).SO

< RESISTOR > R3102 R3105 R3106 R3107 R3108

1-208-719-11 1-208-719-11 1-218-985-11 1-218-985-11 1-218-967-11

METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP

33K 33K 470K 470K 15K

0.5% 0.5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

R3109 R3110 R3111 R3112 R3113

1-218-990-11 1-218-973-11 1-218-975-11 1-218-969-11 1-218-977-11

SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP

0 47K 68K 22K 100K

5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W

R3114 R3116 R3117 R3121 R3122

1-218-975-11 1-218-989-11 1-218-990-11 1-218-929-11 1-218-929-11

RES-CHIP RES-CHIP SHORT RES-CHIP RES-CHIP

68K 1M 0 10 10

5% 5%

1/16W 1/16W

5% 5%

1/16W 1/16W

R3123 R3124 R3125 R3126 R3127

1-218-929-11 1-218-941-11 1-218-985-11 1-218-990-11 1-218-981-11

RES-CHIP RES-CHIP RES-CHIP SHORT RES-CHIP

10 100 470K 0 220K

5% 5% 5%

1/16W 1/16W 1/16W

5%

1/16W

R3128 R3131 R3132 R3133 R3134

1-218-977-11 1-218-977-11 1-218-965-11 1-218-965-11 1-216-847-11

RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP

100K 100K 10K 10K 150K

5% 5% 5% 5% 5%

1/16W 1/16W 1/16W 1/16W 1/16W

Ver 1.1 2000. 06

PD-124 Ref. No.

Part No.

Description

Remarks

R3135 R3136 R3137

1-218-977-11 RES-CHIP 1-218-990-11 SHORT 1-218-974-11 RES-CHIP

100K 0 56K

5%

1/16W

5%

R3139 R3140

1-218-963-11 RES-CHIP 1-218-941-11 RES-CHIP

6.8K 100

5% 5%

1/16W (TRV20E) 1/16W 1/16W

R3141 R3142 R3143 R3144 R3146

1-218-941-11 1-218-941-11 1-218-990-11 1-218-990-11 1-220-207-81

RES-CHIP RES-CHIP SHORT SHORT RES-CHIP

100 100 0 0 110K

5% 1/16W 5% 1/16W (TRV20E) (TRV6/TRV6E) 5% 1/16W (TRV20E)

R3147 R3148 R3149 R3150 R3151

1-218-965-11 1-216-864-11 1-218-990-11 1-216-864-11 1-218-990-11

RES-CHIP METAL CHIP SHORT METAL CHIP SHORT

10K 0 0 0 0

5% 5%

1/16W 1/16W

5%

1/16W

R3152

1-208-860-81 METAL CHIP

75

0.5%

R3152 R3153

1-218-990-11 SHORT 1-208-860-81 METAL CHIP

0 75

R3153 R3154

1-218-990-11 SHORT 1-208-860-81 METAL CHIP

0 75

R3154 R3157 R3158 R3159 R3160

1-218-990-11 1-218-977-11 1-218-977-11 1-218-977-11 1-218-977-11

SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP

0 100K 100K 100K 100K

(TRV6/TRV6E) 5% 1/16W 5% 1/16W 5% 1/16W 5% 1/16W

R3171 R3172 R3173 R3174 R3175

1-216-864-11 1-216-864-11 1-216-864-11 1-216-855-11 1-218-961-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP

0 0 0 680K 4.7K

5% 5% 5% 5% 5%

1/16W (TRV20E) (TRV6/TRV6E) 0.5% 1/16W (TRV20E) (TRV6/TRV6E) 0.5% 1/16W (TRV20E)

Ref. No.

SE-107

Part No.

Description

VC-240

VC-241 Remarks

A-7094-887-A VC-240(H) BOARD, COMPLETE (SERVICE) (TRV20/TRV20E) ************************************** (Ref.No.;10000Series) ************************************************************ A-7094-995-A VC-241 (M) BOARD, COMPLETE (SERVICE) (TRV11/TRV11E:AUS,E,HK,JE,CN) ************************************** A-7094-996-A VC-241(L) BOARD, COMPLETE (SERVICE) (TRV6/TRV6E:AUS,E,HK,JE,CN) ************************************** A-7094-997-A VC-241 (L-CE) BOARD, COMPLETE (SERVICE) (TRV6E:AEP,UK) ************************************** A-7094-963-A VC-241(M-CE) BOARD, COMPLETE (SERVICE) (TRV11E:AEP,UK) ************************************** (Ref.No.;10000Series) ************************************************************

1/16W 1/16W 1/16W 1/16W 1/16W

R3176 1-218-953-11 RES-CHIP 1K 5% 1/16W R3177 1-216-864-11 METAL CHIP 0 5% 1/16W ************************************************************ A-7074-311-A SE-107 BOARD, COMPLETE ********************** (Ref.No.;4000Series) < PHOTO INTERRUPTER > PH081 8-749-011-97 PHOTO INTERUPTER GP1S93 PH082 8-749-011-97 PHOTO INTERUPTER GP1S93 ************************************************************

6-21

Electrical parts list of the VC-240/241 board are not shown. pages 6-23 to 6-44 are not shown.

Ref. No.

Part No.

Description

Remarks

MISCELLANEOUS ************* 15 18 62 103 104

1-694-493-11 1-677-561-11 1-418-979-11 1-960-425-11 1-960-426-11

1-418-877-21 TRANSFORMER UNIT, INVERTER

153 154 158 0 162

1-960-425-11 1-960-426-11 1-677-563-21 1-418-877-11

209 209 209 209 213 253 254 266 302 302 306 307 307 325 332

Part No.

0 ND901

1-517-869-41 TUBE, FLUORESCENT,COLD CATHODE (TRV11/TRV11E) 1-517-869-51 TUBE, FLUORESCENT,COLD CATHODE(TRV20E) 8-729-028-71 TRANSISTOR PN 166, SO (TAPE END) 8-729-028-71 TRANSISTOR PN 166, SO (TAPE TOP) 1-771-326-41 SWITCH, PUSH LEVER (1 KEY) (CC DOWN)

0 ND901 Q901 Q902 S903

TERMINAL BOARD, BATTERY FP-179 FLEXIBLE SWITCH BLOCK, CONTROL(CF30150) HARNESS (PC-118) HARNESS (PC-119)

0 112

Ref. No.

ACCESSORIES ************

(TRV6/TRV6E) HARNESS (PC-118) HARNESS (PC-119) FP-181 FLEXIBLE TRANSFORMER UNIT, INVERTER (TRV11/TRV11E/TRV20/TRV20E) 0

0 0

1-785-594-11 CONNECTOR (HOT SHOE), OUTER 1-758-155-21 FILTER BLOCK, OPTICAL (TRV6/TRV6E/TRV11/TRV11E) 1-758-353-11 FILTER BLOCK, OPTICAL (TRV20/TRV20E) 1-677-562-11 FP-180 FLEXIBLE 1-677-566-21 FP-219 FLEXIBLE, COMPLETE (TRV6/TRV6E/TRV11/TRV11E)

IC101 IC3000 IC3000 LCD901

A-7031-073-A A-7031-011-A A-7031-012-A 1-803-856-21

FP-228 FLEXIBLE FP-100 FLEXIBLE DIODE LA57A,SO (TAPE LED) ELEMENT, HOLE HW-105A-CDE-T (S REEL) ELEMENT, HOLE HW-105A-CDE-T (T REEL)

0

0

0 0

0 CCD BLOCK ASSY (TRV20/TRV20E) CCD BLOCK ASSY (TRV6/TRV11) CCD BLOCK ASSY (TRV6E/TRV11E) INDICATOR MODULE LIQUID CRYST (TRV11/TRV11E) LCD901 1-803-862-21 INDICATOR MODULE LIQUID CRYST (SERVICE) (TRV20) LCD901 LCD901 LCD903 LCD903 M901 M902 M903 MIC901 0 ND901 0 ND901

1-475-141-21 REMOTE COMMANDER (RMT-808) (TRV6/TRV6E:AUS,E,HK,JE,CN) 1-475-141-31 REMOTE COMMANDER (RMT-809) (TRV6E:AEP,UK) 1-475-599-11 ADAPTOR, AC (AC-L10) (TRV6:US,CND,HK,E,JE/TRV6E:AEP,UK,AUS,E,HK,JE/ TRV11:US,CND,HK,E,JE/TRV11E:AEP,UK,AUS,E,HK,JE/ TRV20:US,CND,HK,E,JE/TRV20E:AEP,UK,AUS,E,HK,JE) 1-475-599-71 ADAPTOR, AC (AC-L10) (TRV6:KR/TRV11:KR/TRV20:KR) 1-475-599-81 ADAPTOR, AC (AC-L10) (TRV6E:CN/TRV11E:CN/TRV20E:CN) 1-475-950-21 REMOTE COMMANDER (RMT-811) (TRV11/TRV11E:AUS,E,HK,JE,CN/TRV20/TRV20E) 1-475-950-31 REMOTE COMMANDER (RMT-812) (TRV11E:AEP,UK) 1-569-007-11 ADAPTOR, CONVERSION 2P (TRV6:JE/TRV6E:JE/TRV11:JE/TRV11E:JE/ TRV20:JE/TRV20E:JE) 1-569-008-21 ADAPTOR, CONVERSION 2P (TRV6:E,HK/TRV6E:E,HK/TRV11:E,HK/TRV11E:E,HK/ TRV20:E,HK/TRV20E:E,HK) 1-573-291-11 CONNECTOR, CONVERSION (21P) (TRV6E:AEP,UK/TRV11E:AEP,UK/TRV20E:AEP,UK)

1-677-565-11 FP-183 FLEXIBLE (TRV11/TRV11E/TRV20/TRV20E) 1-785-593-31 CONNECTOR, MEMORY STICK (TRV11/TRV11E/TRV20/TRV20E) 1-418-972-11 SWITCH BLOCK, CONTROL (PS30150) 8-848-737-01 DEVICE, LENS LSV-650B (TRV6/TRV6E/TRV11/TRV11E) 8-848-739-01 DEVICE, LENS LSV-690A (TRV20/TRV20E)

1-677-049-11 1-677-084-11 8-719-078-71 8-719-067-74 8-719-067-74

Remarks

SP901 1-529-590-11 SPEAKER (2.0CM) ************************************************************

1-418-973-31 SWITCH BLOCK, CONTROL (FK30150) (TRV11/TRV11E:AUS,E,HK,JE,CN/TRV20/TRV20E) 1-418-973-41 SWITCH BLOCK, CONTROL (FK30150) (TRV11E:AEP,UK) 1-418-973-51 SWITCH BLOCK, CONTROL (FK30150) (TRV6/TRV6E:AUS,E,HK,JE,CN) 1-418-973-61 SWITCH BLOCK, CONTROL (FK30150) (TRV6E:AEP,UK) 1-785-247-21 CONNECTOR, DC-IN

811 812 D901 H901 H902

Description

0

0

8-753-050-44 8-753-050-53 8-753-026-77 A-7094-871-A

ACX305AK-J (SERVICE)(TRV20E) ACX300CKA-1 (TRV6/TRV6E) LCX033AK-1 (TRV20/TRV20E) LCX032AK-1/5 COMPL (TRV6/TRV6E/TRV11/TRV11E) A-7048-940-A DRUM BLOCK ASSY (DEH-18A-R)(SERVICE)

8-835-685-01 A-7094-823-A 1-418-351-21 1-517-751-51

MOTOR, DC SCD18A/C-NP (INCLUDING BELT) MOTOR BLOCK ASSY, L MICROPHONE UNIT TUBE, FLUORESCENT,COLD CATHODE (TRV6/TRV6E) 1-517-869-31 TUBE, FLUORESCENT,COLD CATHODE (TRV20)

6-45

1-696-819-11 CORD,POWER (TRV6E:AUS/TRV11E:AUS/TRV20E:AUS) 1-765-080-11 CORD,CONNECTION (A/V)(1.5m) 1-769-608-11 CORD,POWER (TRV6:E/TRV6E:AEP,E/TRV11:E/TRV11E:AEP,E/ TRV20:E/TRV20E:AEP,E) 1-776-985-11 CORD,POWER (TRV6:KR/TRV11:KR/TRV20:KR) 1-782-476-11 CORD,POWER (TRV6E:CN/TRV11E:CN/TRV20E:CN) 1-783-374-11 CORD,POWER (TRV6:HK/TRV6E:UK,HK/TRV11:HK/TRV11E:UK,HK/ TRV20:HK/TRV20E:UK,HK) 1-790-073-11 CORD,POWER 2P (TRV6:JE/TRV6E:JE/TRV11:JE/TRV11E:JE/ TRV20:JE/TRV20E:JE) 1-790-107-22 CORD,POWER (TRV6:US,CND/TRV11:US,CND/TRV20:US,CND) 1-792-451-11 CABLE,RS 232C (TRV11/TRV11E/TRV20/TRV20E) 3-053-056-01 LID,BATTERY CASE (FOR RMT-811,812) (TRV11/TRV11E/TRV20/TRV20E)

Be sure to read “Precautions upon replacing CCD imager” on page 4-12,14 when changing the CCD imager. Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

Ref. No.

Part No.

Description

Remarks

Ref. No.

3-057-401-01 HOOD,LENS (TRV20/TRV20E) 3-059-592-11 MANUAL, INSTRUCTION (ENGLISH) (TRV6:US,CND,E,HK,JE/TRV11:US,CND,E,HK,JE/ TRV20:US,CND,E,HK,JE) 3-059-592-21 MANUAL, INSTRUCTION (FRENCH) (TRV6:CND/TRV11:CND/TRV20:CND) 3-059-592-31 MANUAL, INSTRUCTION (SPANISH/PORTUGUESE) (TRV6:E,JE/TRV11:E,JE/TRV20:E,JE) 3-059-592-41 MANUAL, INSTRUCTION (TRADITIONAL CHINESE) (TRV6:E,HK/TRV11:E,HK/TRV20:E,HK) 3-059-592-51 MANUAL, INSTRUCTION (KOREAN) (TRV6:JE,KR/TRV11:JE,KR/TRV20:JE,KR) 3-059-592-61 MANUAL, INSTRUCTION (ARABIC) (TRV6:E/TRV11:E/TRV20:E) 3-059-593-11 MANUAL, INSTRUCTION (ENGLISH/RUSSIAN) (TRV6E:AUS,E,HK,JE,CN/TRV11E:AUS,E,HK,JE,CN/ TRV20E:AUS,E,HK,JE,CN) 3-059-593-21 MANUAL, INSTRUCTION (FRENCH/GERMAN) (TRV6E:E,JE/TRV11E:E,JE/TRV20E:E,JE) 3-059-593-31 MANUAL, INSTRUCTION (ARABIC/PERSIAN) (TRV6E:E/TRV11E:E/TRV20E:E) 3-059-593-41 MANUAL, INSTRUCTION (SIMPLIFIED CHINESE) (TRV6E:E,JE,CN/TRV11E:E,JE,CN/TRV20E:E,JE,CN) 3-059-593-51 MANUAL, INSTRUCTION (TRADITIONAL CHINESE) (TRV6E:HK/TRV11E:HK/TRV20E:HK) 3-059-594-11 MANUAL, INSTRUCTION (ENGLISH/RUSSIAN) (TRV6E:AEP,UK/TRV11E:AEP,UK/TRV20E:AEP,UK) 3-059-594-21 MANUAL, INSTRUCTION (FRENCH/GERMAN) (TRV6E:AEP/TRV11E:AEP/TRV20E:AEP) 3-059-594-31 MANUAL, INSTRUCTION (SPANISH/PORTUGUESE) (TRV6E:AEP/TRV11E:AEP/TRV20E:AEP) 3-059-594-41 MANUAL, INSTRUCTION (ITALIAN/DUTCH) (TRV6E:AEP/TRV11E:AEP/TRV20E:AEP) 3-060-457-11 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (ENGLISH) (TRV11:US,CND,E,HK,JE/TRV20:US,CND,E,HK,JE) 3-060-457-21 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (FRENCH) (TRV11:CND/TRV20:CND) 3-060-457-31 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (TRADITIONAL CHINESE) (TRV11:E,HK/TRV11E:HK/TRV20:E,HK/TRV20E:HK)

6-46E

Part No.

Description

Remarks

3-060-457-41 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (KOREAN) (TRV11:JE,KR/TRV20:JE,KR) 3-060-458-11 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (ENGLISH/RUSSIAN) (TRV11E/TRV20E) 3-060-458-21 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (FRENCH/GERMAN) (TRV11E:AEP,E,JE/TRV20E:AEP,E,JE) 3-060-458-31 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (ITALIAN/DUTCH) (TRV11E:AEP/TRV20E:AEP) 3-060-458-41 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (SPANISH/PORTUGUESE) (TRV11:E,JE/TRV11E:AEP/TRV20:E,JE/TRV20E:AEP) 3-060-458-61 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (ARABIC/SWEDISH) (TRV11:E/TRV11E:E/TRV20:E/TRV20E:E) 3-060-458-71 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (SIMPLIFIED CHINESE) (TRV11E:E,JE,CN/TRV20E:E,JE,CN) 3-060-476-01 DISK, SYSTEM (PICTURE GEAR 4.1 LITE) (TRV11/TRV11E/TRV20/TRV20E) 3-742-854-21 LID, BATTERY CASE (FOR RMT-808,809) (TRV6/TRV6E) 3-987-015-01 BELT(S), SHOULDER A-7033-740-A MEMORY STICK (TRV11/TRV11E/TRV20/TRV20E)

〈OPTICAL

AXIS FRAME〉

Take a copy of OPTICAL AXIS FRAME with a clear sheet for use.

✂

DCR-TRV6/TRV6E/TRV11/TRV11E

— 247 —

〈FOR

CAMERA COLOR REPRODUCTION ADJUSTMENT〉

For NTSC model

DCR-TRV6/TRV11 Take a copy of CAMERA COLOR REPRODUCTION FRAME with a clear sheet for use.

✂ For PAL model

— 248 —

✂

DCR-TRV6E/TRV11E

〈FOR

CAMERA COLOR REPRODUCTION ADJUSTMENT〉

For NTSC model

DCR-TRV20 Take a copy of CAMERA COLOR REPRODUCTION FRAME with a clear sheet for use.

✂ For PAL model

✂

DCR-TRV20E

— 249 —

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

9-929-818-31

Sony EMCS Co.

— 250 —

2003F1600-1 ©2003.6 Published by DI CS Strategy Div.

DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E

RMT-808/809/811/812 US Model Canadian Model Korea Model DCR-TRV6/TRV11/TRV20

SERVICE MANUAL

AEP Model UK Model Australian Model Chinese Model

Level 2

DCR-TRV6E/TRV11E/TRV20E

2000. 06

E Model Hong Kong Model Tourist Model DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E

CORRECTION-1 Correct your service manual as shown below. (00-002)

• Errors in SECTION 5. ADJUSTMENT and SECTION 6. REPAIR PARTS LIST are corrected as follows.

: Changed portion. Page

INCORRECT

CORRECT

SECTION 5. ADJUSTMENT

VC-241 board JK-188 board PD-123 board PD-124 board LB-64 board VC-241 board VC-241 board VC-241 board

(COMPLETE) (COMPLETE) (COMPLETE) *1 (COMPLETE) *2 (COMPLETE) IC801 (EEPROM) IC502 (EEPROM) IC1407 (Flash memory) *1

4. D Page Table

4. D Page Table

*1: TRV11/TRV11E/TRV20E model only *2: TRV6/TRV6E/TRV20 model only

*1: TRV11/TRV11E/TRV20 model only

Board replacement

5-12

(COMPLETE) (COMPLETE) (COMPLETE) *1 (COMPLETE) *2 (COMPLETE) IC801 (EEPROM) IC502 (EEPROM) IC1406 (EEPROM) *1

Board replacement

5-3

VC-241 board JK-188 board PD-123 board PD-124 board LB-64 board VC-241 board VC-241 board VC-241 board

SECTION 5. ADJUSTMENT

*2: TRV6/TRV6E/TRV20E model only

5-14

4. Modification of B Page Data (DCR-TRV11/TRV11E)

4. Modification of B Page Data (DCR-TRV11/TRV11E)

Processing after Completing Modification of B Page data:

Processing after Completing Modification of B Page data:

3)

3)

Select page: 5, address: 00, set data: 01, and press the PAUSE button. (The changed data are written in the EEPROM.)

Select page: 5, address: 00, set data: 01, and press the PAUSE button. (The changed data are written in the flash memory.)

: Changed portion. Page

: Deleted portion. INCORRECT

CORRECT

5. B Page Table Address

5-15

5. B Page Table Remark

Address

55 to 6F Fixed data-1 (Initialized data) 70 Fixed data-2 71 to FF Fixed data-1 (Initialized data)

Remark

55 to 5D Fixed data-1 (Initialized data) 5E Fixed data-2 5F 60 to 6F Fixed data-1 (Initialized data) 70 Fixed data-2 71 to FF Fixed data-1 (Initialized data)

Table. 5-1-6.

Table. 5-1-6. 4. V-COM Level Adjustment (PD-123 board)

4. V-COM Level Adjustment (PD-123 board)

Note: Perform “Bright Adjustment” and “Contrast Adjustment” before this adjustment.

Note: Perform “RGB AMP Adjustment” and “Contrast Adjustment” before this adjustment.

5. V-COM Adjustment (PD-123 board)

5. V-COM Adjustment (PD-123 board)

Note: Perform “Bright Adjustment” and “Contrast Adjustment” before this adjustment.

Note: Perform “RGB AMP Adjustment”, “Contrast Adjustment” and “V-COM Level Adjustment” before this adjustment.

2. PLL f0 & LPF f0 Adjustment (VC-240/241 board)

2. PLL f0 & LPF f0 Adjustment (VC-240/241 board)

Adjusting method: 5) Select page: 0, address: 01, and set data: 00.

Adjusting method: 5) Select page: 0, address: 01, and set data: 00.

5-38

5-51

5-53

Bit value of page: 3, address: 03 data bit 4 = 1 bit 5 = 1 bit 6 = 1 bit 3 = 1 bit 2 = 1

Error contents PLL f0, even channel is defective PLL f0, odd channel is defective LPF f0 is defective PLL f0, final adjustment is defective PLL f0, final adjustment time-out

Bit value of page: 3, address: 03 data bit 6 = 1 bit 3 = 1 bit 2 = 1

Error contents LPF f0 is defective PLL f0, final adjustment is defective PLL f0, final adjustment time-out

5. PLL f0 & LPF f0 Final Adjustment (VC-240/241 board)

5. PLL f0 & LPF f0 Final Adjustment (VC-240/241 board)

Adjusting method: 5) Select page: 0, address: 01, and set data: 00.

Adjusting method: 5) Select page: 0, address: 01, and set data: 00.

Bit value of page: 3, address: 03 bit 4 = 1 bit 5 = 1 bit 6 = 1 bit 3 = 1 bit 2 = 1

Error contents PLL f0, even channel is defective PLL f0, odd channel is defective LPF f0 is defective PLL f0 final adjustment is defective PLL f0 final adjustment time-out

—2—

Bit value of page: 3, address: 03 bit 6 = 1 bit 3 = 1 bit 2 = 1

Error contents LPF f0 is defective PLL f0 final adjustment is defective PLL f0 final adjustment time-out

Page

INCORRECT 2-2. MSW Code

Mechanism Position ← UNLOAD SOFF

BL

DS

BL

LE

BL

STOP

BL

FF

BL

RP

BL

RVS

0 0 1 1 = 3

1 1 1 1 = F 1 0 1 1 = B

1 1 1 1 = F 0 1 1 1 = 7

1 1 1 1 = F 0 1 0 1 = 5

1 1 1 1 = F 1 0 0 1 = 9

1 1 1 1 = F

BL

1 1 1 1 = F 1 1 0 1 = D

1 0 1 0 = A

USE

1 1 1 1 = F 1 1 0 0 = C

BL

1 1 1 1 = F 1 1 1 0 = E

EJECT

LOAD →

LS chassis movement range Pinch roller is pressed

Tension regulator ON

Releasing lock of cassette compartment

5-67

Position

Code

EJECT

A

BL

F

USE

E

SOFF DS LE

C D 9

STOP

5

FF

7

RP

B

RVS

3

NULL

0

Contents Position at which the cassette compartment lock is released, and position at the farthest unload side mechanically at which the mechanism can move no further in the UNLOAD direction. BLANK code, at the boundary between codes. The mechanism will not stop at this code during operations. (Excluding LOAD/UNLOAD) EJECT completion position. When the cassette is ejected, the mechanism will stop at this position. Cassette IN standby. The guide will start protruding out as the mechanism moves towards the LOAD position. Code during loading. Code outputs while the LS chassis is moving. LS operations and guide loading are performed here. Current limiter is turned off. Stop position in the loading state. The pinch roller separates, the tension regulator returns, and the brake is imposed on both reels. FF position. The tension regulator is half on. This position is not used except for the FF mode. PB, REC, CUE, Pause, FX2, FWD-SLOW positions. When the pinch roller is pressed, and the tension regulator is ON, the mechanism is operating at this position in modes in which normal images are shown. Reverse running position. REW, REV, RX1, RX2, and RVS-SLOW are performed at this position. Code not existing in the MD. When errors occur when the loading motor is not driving, this code is memorized.

—3—

DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E

: Changed portion. Page

CORRECT 2-2. MSW Code

Mechanical Position ← UNLOAD BL

EJ

LOAD → BL

ULE

SR

BL

GL

BL

STOP

BL

R/P

1 1 0 = 6

1 1 1 = 7 0 1 0 = 2

1 1 1 = 7 0 1 1 = 3

1 1 1 = 7 0 0 1 = 1

1 1 1 = 7 1 0 1 = 5

1 1 1 = 7

1 0 0 = 4

← C (MSB) ←B ← A (LSB)

LS chassis movement section

5-67

Lock released Cassette compartment

Position

Code

EJ

4

BL

7

ULE

5

SR GL

1 3

STOP

2

R/P

6

NULL

0

Pinch roller pressing

Contents Position at which the cassette component lock is released, at the farthest unload side mechanically at which the mechanism can move no further in the UNLOAD direction. BLANK code, at the boundary between codes. EJECT completion position. when the cassette is ejected, the mechanism will stop at this position. Cassette IN standby. The guide will start protruding out as the mechanism moves towards the LOAD position. Position at which it is possible to release the S ratchet. Guide loading are performed here. Stop position in the loading state. The pinch roller separates, the tension regulator returns, and the brake is imposed on both reels. PB, REC, CUE, REVIEW, PAUSE positions. When pinch roller is pressed, and the tension regulator is ON, the mechanism is operating at this position in modes in which normal images are shown. Code not existing in the MD. Default value.

INCORRECT

CORRECT

SECTION 6. REPAIR PARTS LIST Ref. No. 210

6-5 210 210

6-21

9-929-818-91

Part No.

Description

SECTION 6. REPAIR PARTS LIST Remarks

Ref. No.

A-7074-995-A VC-241 (M) BOARD, COMPLETE (SERVICE) (TRV11/TRV11E:AUS,E,HK,JE,CN) A-7074-996-A VC-241 (L) BOARD, COMPLETE (SERVICE) (TRV6/TRV6E:AUS,E,HK,JE,CN) A-7074-997-A VC-241 (L-CE) BOARD, COMPLETE (SERVICE)(TRV6E:AEP,UK)

210 210 210

A-7074-995-A VC-241 (M) BOARD, COMPLETE (SERVICE) (TRV11/TRV11E:AUS,E,HK,JE,CN) *********************************** A-7074-996-A VC-241(L) BOARD, COMPLETE (SERVICE) (TRV6/TRV6E:AUS,E,HK,JE,CN) *********************************** A-7074-997-A VC-241 (L-CE) BOARD, COMPLETE (SERVICE)(TRV6E:AEP,UK) ***********************************

Sony EMCS Co.

—4—

Part No.

Description

Remarks

A-7094-995-A VC-241 (M) BOARD, COMPLETE (SERVICE) (TRV11/TRV11E:AUS,E,HK,JE,CN) A-7094-996-A VC-241 (L) BOARD, COMPLETE (SERVICE) (TRV6/TRV6E:AUS,E,HK,JE,CN) A-7094-997-A VC-241 (L-CE) BOARD, COMPLETE (SERVICE)(TRV6E:AEP,UK)

A-7094-995-A VC-241 (M) BOARD, COMPLETE (SERVICE) (TRV11/TRV11E:AUS,E,HK,JE,CN) *********************************** A-7094-996-A VC-241(L) BOARD, COMPLETE (SERVICE) (TRV6/TRV6E:AUS,E,HK,JE,CN) *********************************** A-7094-997-A VC-241 (L-CE) BOARD, COMPLETE (SERVICE)(TRV6E:AEP,UK) ***********************************

2001K1600-1 ©2001.11 Published by DI Customer Center

DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E

RMT-808/809/811/812 US Model Canadian Model Korea Model DCR-TRV6/TRV11/TRV20

SERVICE MANUAL

AEP Model UK Model Australian Model Chinese Model

Level 2

DCR-TRV6E/TRV11E/TRV20E

Ver 1.3 2003. 06

SUPPLEMENT-1

E Model Hong Kong Model Tourist Model

File this supplement with the Service Manual. (PV03-001)

DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E

• Change of IC (Version up)

SECTION 5 ADJUSTMENTS 1. Before starting adjustment : Supplied portion.

IC102 (REC/PB AMP) IC1901 (IR transmitter) IC802 (Camera controll) *3

Adjustment Section

VC-241 board VC-241 board

Adjustment Section

NEW

VC-241 board VC-241 board VC-241 board

5-2

IC102 (REC/PB AMP) IC1901 (IR transmitter)

1-1. Adjusting items when replacing main parts and boards. Page FORMER

Supplied contents *3: When IC802 of the VC-241 board is going to be exchanged, the data on page : E, address : 53 and the data 6F must be modified. Be sure to enter the following data without fail. 5-3

Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: E, address: 53, set data: 01, and press the PAUSE button. 3) Select page: E, address: 6F, set data: 82, and press the PAUSE button. 4) Select page: 0, address: 01, and set data: 00.

9-929-818-82

Sony EMCS Co.

2003F1600-1 ©2003.6 Published by DI CS Strategy Div.

Reverse

992981834.pdf

Revision History History

Contents

S.M. Rev. issued —

Ver.

Date

1.0

2000.03

Official Release

1.1

2000.06

Correction-1

Error correction S.M. correction: Page 5-3, 5-12, 5-14, 5-15, 5-38, 5-51, 5-53, 5-67, 6-5, 6-21

Yes

1.2

2001.11 2003.06

Correction of Self-diagnosis code S.M. correction: Page 10 Change of IC (Version up)

Yes

1.3

Correction-2 (PV01-037) Supplement-1

—

No