Ventilation Control System - Electric Bargain Store
40 MIN. 60 MIN. Ventilation Control System. I n t r o d u c t i o n. The different wall controls offered by ... This allows every room to have a RTS3 if required.
Ve n t i l a t i o n C o n t r o l S y s t e m I n t r o d u c t i o n The different wall controls offered by Fantech are designed to meet your needs while being visually appealing. They will enable you to maximize the use and enjoyment of your ventilation system.
PLEASE NOTE This RTS3 timer is compatible with electrical board: Uni-Ctrl
RTS3 20/40/60 MINUTE TIMER
This switch can be placed in the kitchen, bathroom or any other central location.
20 MIN 40 MIN 60 MIN
PUSH
The Fantech RTS3 timer is compatible with all Fantech HRV/ERV models except the KHP and the HRV-XI Series.This control activates the system on continuous mode for either 20, 40 or 60 minutes depending on your selection, it then returns to the predetermined setting. To cancel this operation, simply press the button until the LED light turns off.
Operation By pressing the RTS3 button once, the LED light turns green and the ventilation system will operate on HIGH speed for 20 minutes. Pressing again, the LED will turn yellow and the timer will be set for 40 minutes. Pressing a third time, the LED is RED and the timer is set for 60 minutes. Press a fourth time to cancel the timer (LED turns off).
Tools needed pen-type screwdriver
Equipment 3 wires (min. 26 gage)
3 wire Insert the stripped end of the wires into the terminal connections,located on the outside of the HRV or ERV cabinet near the power cord, marked DEH -, DEH + and COM. Using a pen-type screwdriver, tighten the screws. Run the wires to the RTS3. Insert the stripped end of the the wires into the electrical connection marked DEH -, DEH + and COM. Using a pen-type screwdriver, tighten the screws. Multiple RTS3 can be connected in parallel. This allows every room to have a RTS3 if required.
RTS3
Item# 403259: RTS3 Rev Date: 122005
Système de contrôle de ventilation I n t r o d u c t i o n Les différents contrôles muraux offerts par Fantech ont été conçus afin de répondre à vos besoins tout en étant attrayants. Ils vous permettront de maximiser votre usage et jouissance de votre système de ventilation.
VEUILLEZ NOTEZ La minuterie RTS3 est compatible avec la carte uni-commande électronique. Elle peut être posée dans la cuisine, la salle de bains ou tout autre endroit centralisé.
Minuterie RTS3 20/40/60
20 MIN 40 MIN 60 MIN
PUSH
La minuterie RTS3 de Fantech est compatible avec tous les modèles VRC/VRE de Fantech sauf les séries KHP et HRV-XI. Elle fait fonctionner le système en mode continu pendant 20, 40 ou 60 minutes, puis retourne à son réglage prédéterminé. Pour annuler la minuterie, il suffit d’appuyer sur le bouton jusqu’à ce que le voyant DEL s’éteigne.
Fonctionnement Enfoncer le bouton de la minuterie RTS3 une fois et le voyant LED devient vert; le système de ventilation fonctionne à haute vitesse pendant 20 minutes. Enfoncer de nouveau le bouton, le voyant DEL passe au jaune; la minuterie est réglée pour faire fonctionner le système pendant 40 minutes. Enfoncer une troisième fois le bouton, le voyant DEL passe au ROUGE; la minuterie est alors réglée pour faire fonctionner le système pendant 60 minutes. Enfoncer le bouton une quatrième fois et la minuterie s’arrête (le voyant DEL s’éteint).
Outils tournevis mince
Équipement 3 fils (calibre 26 min.)
3 fils Insérer l’extrémité dénudée des fils dans les raccordements des bornes DEH -, DEH + et COM situées à l’extérieur de l’armoire du VRC ou du VRE, à proximité du cordon d’alimentation. Serrer les vis à l’aide d’un stylo-tournevis. Acheminer les fils jusqu’à la minuterie RTS3. Insérer l’extrémité dénudée des fils dans les raccordements des bornes DEH-, DEH+ et COM. Serrer les vis à l’aide d’un stylo-tournevis. Plusieurs minuteries RTS3 peuvent être montées en parallèle. De cette façon, il est possible de munir chaque pièce d’une minuterie RTS3.
bottom edge of the ceiling joist on models with 4" duct connection and. 15/32" up from ... There are no warranties which extend beyond the description on the.
Not Use To Exhaust Hazardous Or Explosive. Material and Vapors.â 4. .... Connect flex duct to the fan with plastic zip ties or duct tape. Connections should be ...
à HAUT DÃBIT LORSQU'UN OU. LES DEUX PORTES SONT OUVERTES. COMMUN. NORM. FERMÃ. INTERRUPTEURS. DE PORTE. OPTIONNELS. (ASDS). NORM. OUVERT. 4. CONDENSATEUR. 6 uF. 1. 2. UNITà MAÃTRE. AS 4006. AS 4009. AS 6008. AS 6012. CONTACTEUR DE. L'APPAREIL DE
21 mai 2012 - Siempre desconecte la energÃa durante la instalación o el mantenimiento. â·Abra el accesorio aflojando el tornillo de abajo (1) â (Vea la Figura ...
Nov 21, 2002 - Removing and installing Repair Manual, Body. Interior, Repair .... Loosen refrigerant line clamp and remove lines from evaporator. - Secure ...
Sprocket wheel drive ... S35/35 mm, S16/16 mm, Leica Slide, Vistavision and ... To date, capstan drive has proven the most common ..... White/black shading.
Podiatry chair with a very comfortable design. 3 motors control height, backrest and seat inclination. Horizon- tally wide-apart leg-rests movement (90°) with height regulation by gas lift. Reversible arms and adjustable headrest. A 5-motor model (2
If not, configuration which is set automatically by selecting vehicle model .... INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously. - It operates ...... AUTO LOCK SET. Auto door ... Buzzer: Sound Intelligent Key warning buzzer.
correctly to the wiring terminal block. Air is too dry. 1. ... NOTE: See Cleaning Steps on page 11 for the above maintenance items. ... 69-2481EF—01 M.S. 03-11.
the RangeLink has a micro-power mode built in, so you can do the pre-flight ... Power source for header tracker. .... (=R/C V+ )for headertracker power supply .... There is a switch-mode regulator built in the RangeLink Transmitter module, you ...
the fall, winter & early spring seasons. Drain hose is connected to the drain pan and serves as drainage for the accumulation of water. It is normal during summer ...
IP address can be configured manually on the device itself or with the OCS software under Ethernet Config. The IP address of the LD. DSP44K or DSP45K amplifier is set at the factory to 192.168.0.100. This means that a different IP address must be use
spinal reflexes, subroutines of motor impulses from the central nervous system, and .... on the various flexor muscles of the arm, xhich cause the elbow to bend.
delay calculation), to define minimum and maximum values in the Frequency Response window, to activate unwrapped phase range and to switch the phase .... Single – each channel is individually adjustable via CHANNEL EDIT and SPEAKER PRESET EDIT and ca
AbstractâMRI based nano- and microrobotics show good potential for new targeted .... an average particle size of 10nm in oil buffer, FerroTec. Corporation) was ...
If one wanted to do a climbing turn to the right he simply leads into this with the head and shoulders by turning his head and shoulders to the right - at the same ...
d'air efficace offre une protection optimale contre les vapeurs, gaz et ... d'air dans la zone de travail ou le niveau de saturation des .... e-mail: [email protected].
13. Complete Installation. 1. Plug the optional remote up/down switch into the front panel of the vent box. ..... user, operator or installation instructions. 2. In-home ...