Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket; repeat for remaining sockets. Screw the ...
Vanity Strip GENERAL PRODUCT INFORMATION: This product is listed by one of the following “Nationally Recognized Testing Laboratory”
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is suitable for damp locations.
Use minimum 90°c supply conductors.
This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
1A LAMP
7
ELECTRICAL BOX NEUTRAL WIRE
COLLAR NUT SPACER
1
WHITE WIRE
1 SHADE
6
MOUNTING PLATE MOUNTING PLATE SCREW
SOCKET HOT WIRE BLACK WIRE FIXTURE SCREW
5 ALLEN WRENCH
1
Secure the mounting plate to the electrical box with the two mounting plate screws.
2
Connect the fixture ground wire to a suitable ground in accordance to local electrical codes.
3
Connect the white fixture wire to the neutral power line wire with a wire nut.
4
Connect the black fixture wire to the hot power line wire with a wire nut.
5
Mount the fixture base onto the mounting plate and secure it with the fixture screws using an Allen wrench.
6
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket; repeat for remaining sockets.
7
Screw the lamp(s) into the socket(s). Refer to the label on the lamp socket for Max Wattage information.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A 7
AMPOULE
BOÎTE DE JONCTION
FIL NEUTRE
ECROU DE COLLIER ESPACEUR
1
FIL BLANC
1 6
ABAT-JOUR
PLAQUE DE MONTAGE
VIS DE MONTAGE
DOUILLE FIL CHAUD FIL NOIR VIS DE LUMINAIRE
5 CLÉ ALLEN
1
Fixez la plaque de montage à la boîte de jonction avec les deux vis de montage.
2
Connectez le fil de terre du luminaire à un terrain approprié conformément aux codes électriques locaux.
3
Connectez le fil blanc du luminaire au fil de ligne à neutre avec un écrou de fil.
4
Connectez le fil noir du luminaire au fil ligne électrique chaud avec un serre-fils.
5
Montez la base de luminaire sur la plaque de montage et le fixer avec les vis de luminaire à l'aide d'une clé Allen.
6
Placez l'abat-jour et l'espaceur sur le douille, puis fixez-les en place en vissant l'écrou de collier sur la douille; répéter pour les douilles restantes.
7
Visser la/les ampoule (s) dans la/les douille (s). Reportez-vous à l'étiquette sur la douille de la lampe pour obtenir des informations Max Puissance.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A BOMBILLA
7
CAJA ELÉCTRICA
CABLE NEUTRO
TUERCA DE COLLAR ESPACIADOR
1 CABLE BLANCO
1 PANTALLA
6
PLACE DE MONTAJE TORNILLO DE MONTAJE
ENCHUFE CABLE CALIENTE CABLE NEGRO TORNILLO DE LA LÁMPARA
5 LLAVE DE ALLEN
1
Fije la placa de montaje a la caja de juntura con los dos tornillos de la placa de montaje.
2
Conecte el cable de tierra a una tierra artefacto adecuado de acuerdo a los códigos eléctricos locales.
3
Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con un tapón de alambre.
4
Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre.
5
Monte la base de la lámpara en la placa de montaje y fijarlo con los tornillos la lámpara con una llave Allen.
6
Coloque la pantalla y el espaciador sobre el enchufe, luego fijarlos en su lugar atornillando la tuerca de pantalla en el enchufe; repetir para enchufes restantes.
7
Atornille la(s) bombilla(s) en la(s) enchufe(s). Consulte la etiqueta del casquillo de la lámpara para obtener información Max Potencia.
Secure the mounting plate to the junction box. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. Connect the white ...
Sophie 1, 2, 3, and 4 Light Vanity Strip. 1.1. VS47002-VS47003-VS47004-WB1724. VS47002,VS47003,. VS47004,WB1724. Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground
Connectez le fil de terre du luminaire à un terrain approprié conformément ... Connectez le fil noir du luminaire au fil ligne électrique chaud avec un serre-fils.
Mount the fixture base onto the mounting plate and secure it with the fixture screws. Place the shade over ... without notification. A Generation Brands Company.
Max Potencia.ctamente sobre el enchufe y asegúrelo en su lugar montándolo en el gancho de la lámpara correspondiente. 1. 2. 3. 4. 5. 6. PRECAUCIÃN: RIESGO DE INCENDIO. Este producto debe instalarse de acuerdo con el código de instalación aplica
Mount the fixture base onto the mounting plate and secure it with the fixture ... Monte la base de la lámpara en la placa de montaje y fijarlo con el tornillo de la ...
Connect the fixture ground wire to a suitable ground in accordance to local ... Connect the white fixture wire to the neutral power line wire with a wire nut.
If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely ... If any part is missing or damaged, do not attempt to.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors.
Fije la parte superior del brazo a la cubierta de la lámpara colocando una arandela ... coloque el capuchon decorativo empujándola en el brazo completamente.
Connect the black fixture wire to the hot power line wire with a wire nut. Secure the fixture to the post with the post screws making sure to neatly tuck in all wiring.
Vintner 1 Light Mini-Pendant. Pendant. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction ...
Installation should be carried out in accordance with the latest edition of the National Wiring Regulations. If in doubt, consult a qualified electrician. â¢. The LED Strip operates at 12V DC. A 12V DC LED Driver is required (not included). â¢. Whe