Outdoor GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for wet locations.
1A
FINIAL
SMALL DECORATIVE CUP
WASHER
LARGE DECORATIVE CUP
5 FIXTURE COVER
4
THREADED PIPE
3 LAMP CANDLE TUBE
2
FIXTURE SOCKET
1
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Install the candle tubes by slipping them through the sockets.
3
Install the lamps by screwing them into the sockets. Refer to the label on the lamp socket for Max Wattage information.
4
Screw the threaded pipe to the fixture.
5
Place the fixture cover, large decorative cup, small decorative cup, and washer over the threaded pipe, then secure them in place by tightening the finial.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
FLEURON
PETIT COUPE DÉCORATIF
RONDELLE
GRAND COUPE DÉCORATIF
5 COUVERCLE DE LUMINAIRE
4
TUYAU FILETÉ
3 AMPOULE TUBE BOUGIE
2
LUMINAIRE DOUILLE
1
1
Suivez supplément ci-joint des instructions électriques et installation d'accessoires dans la boîte de prise de maison.
2
Installer les tubes de bougie en les glissant à travers les douilles.
3
Installer les ampoules en les vissant dans les douilles. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
4
Vissez la tuyau filetée pour le luminaire.
5
Placer le couvercle de le luminaire, grande coupe décoratif, petite coupe décoratif et la rondelle sur la tuyau filetée, puis fixez-les en place en serrant le fleuron.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
FINIAL
COPA DECORATIVA PEQUEÑA
ARANDELA
COPA DECORATIVA GRANDE
5 CUBIERTA DE LA LÁMPARA
4
TUBO ROSCADO
3 BOMBILLA TUBO DE VELA
2
LÁMPARA ENCHUFE
1
1
Siga las instrucciones de instalación incluido suplemento para eléctricos y instalación de la lámpara en caja de salida de la casa.
2
Instale los tubos de vela por les escapa de las enchufes.
3
Instale las bombillas atornillándolos en los enchufes. Consulte la etiqueta en el enchufe de la lámpara para obtener información de Max Wattage.
4
Enrosque el tubo roscado a la lámpara.
5
Coloque la cubierta de la lámpara, copa decorativa grande, copa decorativa pequeña y la arandela sobre el tubo roscado y fíjelos en su lugar apretando el finial.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 2. CAP N
Augmenter le logement jusqu'Ã le luminaire de sorte que le attache sort par le haut de le luminaire et les fixer ensemble en vissant le fleuron sur le attache.
This product is listed by one of the following. â ationally ecognized esting aboratoryâ. N. R. T. L ... SUIVEUR DE BOUGIE. PANNEAU. DE VERRE. LOGEMENT. 2.
Install the candle follower by placing it on top of the socket. Screw the lamp into the socket. Refer to the label on the socket for Max Wattage information. Repeat ...
Install all glass panels by carefully sliding them into the fixture and securing them using the clips. Place the shade and spacer over the socket and secure them in ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto house junction box. Raise the housing up to the fixture so that the ...
Fije la parte superior del brazo a la cubierta de la lámpara colocando una arandela ... coloque el capuchon decorativo empujándola en el brazo completamente.
Place the shade and spacer over the socket and secure them in place by screwing the collar nut onto the socket. Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. Install the cover to the fixture arm an
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Secure the mounting plate to the junction box with two mounting plate screws. Screw the ... Mount the fixture base onto the mounting plate and secure it with the fixture screws. .... Feiss reserves the right to ... A Generation Brands Company.
Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground in accordance to local ...
Do not block any ventilation openings. Install in accordance with the ... Contact your local government for disposal or recycling practices in your area.
Place the shade inside the decorative frame and install the brackets to the decorative frame using the bracket screws. Place the decorative frame over the threaded pipe and socket assembly and secure them together using the finial. Follow enclosed su
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Pediment 3 Light Outdoor Post. 1.1. OL11107. OL11107. Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white ...
Connect the black fixture wire to the hot power line wire with a wire nut. ... Refer to the label on the lamp socket for Max Wattage information. Install the glass ...
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut.